How often should I replace my timing belt?
How often should I replace my timing belt?
A broken timing belt can indeed lead to the complete destruction of the engine. To avoid this fate, replace the timing belt every 60,000 miles or every four years. If you live in a dry climate (like Arizona), or if you don’t drive your car often, then I recommend replacing the belt more often.
When to replace timing belt on E30 engine?
Replacing the rubber timing belt is one of the most important maintenance tasks for the six-cylinder E30 engine. As the engine ages and mileage climbs, an old, worn-out timing belt may break, causing catastrophic engine damage.
Where is the O / T mark on the timing belt?
At TDC for cylinder number 1, the O/T mark on the crankshaft pulley timing wheel or vibration damper (green arrow) will line up with the line on the lower timing belt cover (yellow arrow). In addition, the mark on the camshaft sprocket should line up with the mark on the cylinder head.
Where to put the timing belt on a BMW 3 series?
When you install the new timing belt, place it on the engine, working counterclockwise, starting from the crankshaft sprocket. Slip the belt over the intermediate shaft sprocket, around the tensioner, and over the camshaft sprocket. Now, loosen both bolts on the tensioner to apply tension to the timing belt.
You can do a visual check – see if there’s any cracking, glazing, missing teeth or oil contamination. Or you can have a mechanic check the belt for you. Most vehicle manufacturers also recommend that you make timing belt replacement a part of your routine maintenance, replacing it every 60,000 miles. Some belts are good for up to 100,000 miles.
What happens if you snap your timing belt?
Timing belts don’t often snap, but when they do, it can cause piston damage, ruined cylinder heads, and engine valve damage. Probably, when you think of your engine, you picture the valves and pistons, but you don’t think much about what keeps them in good working order. Let’s state it plainly – nothing is more important than the timing belt.
Can a broken timing belt cause bent valves?
Interference vs. non-interference engines. The level of damage caused by a broken timing belt can depend on the type of engine you have in your car. A non-interference engine provides clearance between the valves and pistons, so if the timing belt breaks, you might end up with bent valves, and you might have to have your cylinder heads rebuilt,…
What happens to Honda Accord after timing belt change?
ALSO your honda 4cyliner in the Accord has a BALANCE SHAFT belt as well. This is also a very precise allignment procedure while doing the T-belt service. This will make your cars engine vibrate in an unusual manner after a T-belt job.
Why does it cost so much to replace timing belt?
The main reason timing belt replacement repairs can cost so much though is that you’re often not just replacing the belt. The timing belt system also consists of a series of tensioner and idler bearings, which help guide and drive the belt. It’s often recommended that these are replaced at the same time as part of routine maintenance.
Where is the timing belt on a car?
The general rule of thumb is that if you can see a belt when you open up the hood, it’s a serpentine or drive belt. Timing belts are a much more intricate and sensitive mechanism, and are hidden behind the cam cover on the side or front of the engine.
What happens if I snap my timing belt?
If the timing belt snaps however, you could cause serious, irreparable damage to the engine. That’s not the only risk that timing belts pose though. Whilst they can snap, they are also known to slip if the teeth of the belt wear out.
How much does it cost to replace a cam belt?
You’ve probably heard of fan belts, cam belts, air con belts, alternator belts, power steering belts, drive belts, and serpentine belts. That’s a lot of belts. It also leads to a lot of confusion, when your last belt replacement cost you $80 and now you’re staring down the barrel of $1000 plus for the next one…
How do you replace timing belt on BMW E30?
To reinstall the tensioner, compress the spring as far as you can, and then temporarily tighten the adjustable tensioner bolt (green arrow, Photo 12). When you install the new timing belt, place it on the engine, working counterclockwise, starting from the crankshaft sprocket.
Where is cylinder number 1 on the timing belt?
Look through the cover access hole. If you see another timing mark on the camshaft sprocket aligned with the mark on the inner belt cover, cylinder number 1 is at Top Dead Center (TDC). If not, rotate the crankshaft one complete turn again and check for the alignment marks.
How often do timing belts need to be replaced?
Timing belts last 60,000 to 100,000 miles. check your owner’s manual for the manufacturer’s replacement interval. Your six-year-old econobox is starting to show a bit of wear and tear, but everything mechanical still works fine.
How to watch before doing the timing belt?
Ford 2.3/2.5 Common timing belt mistake! Watch before doing timing belt! – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.
Look through the cover access hole. If you see another timing mark on the camshaft sprocket aligned with the mark on the inner belt cover, cylinder number 1 is at Top Dead Center (TDC). If not, rotate the crankshaft one complete turn again and check for the alignment marks.
How do you change the timing belt on a Ford Ranger?
As you hold the timing belt loose, tighten the assembly adjuster bolt to lock the tensioner using the ratchet, ratchet extension and socket. Now remove the tensioner wrench. Remove the timing belt. Install the new timing belt starting at the crankshaft sprocket.
