Is there a problem with the p0748 OBD-II trouble code?

Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration. When the P0748 OBD-II trouble code is set, the Powertrain Control Module (PCM) has detected a problem with the Transmission Pressure Control Solenoid “A”.

What does p0748 stand for on a PCM?

When the Powertrain Control Module (PCM) detects a continuous open or short in the Pressure Control (PC) solenoid valve circuit the P0748 code is set. The Pressure Control (PC) solenoid valve is an electronic device that regulates transmission line pressure based on the current flow through its coil winding.

How much does it cost to repair a p0748 Chevy?

The cost to diagnose the P0748 CHEVROLET code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

Where are the trouble codes on a 1998 Dakota?

Same as for a pre-1997 Dakota (see below) except the trouble codes will display in the odometer area instead of flashing the check engine light. How to get the codes on a 1998-1999 Dakota: Depress the trip reset and trip/odometer switches, and, while holding them, turn the ignition to ON/RUN, and wait about 5 seconds.

How to find trouble codes for North Dakota?

Dakota Trouble Codes Enter the code(s) you would like to look up in the box below (or leave it blank to see a list of all codes) You can enter codes in either MIL (i.e. 12, 55, etc.) or Scan Tool (i.e. P0300, P0171, etc.) format. If all else fails:

How to find Dakota trouble codes in Excel?

For example, to look up codes 12, 17, and 55, you’d enter 12 17 55 in the box and then hit the “submit” button. If you would like to view all of the codes in the “database”, then just hit the submit button without entering anything in the box.

How much does it cost to repair a Dodge p0740?

The cost of diagnosing the P0740 DODGE code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

Is there a fault in the Dodge Dakota p0440?

P0440 is a fault found in the EVAP or also known as the Evaporative Emission Control System. Next P0456 is also an EVAP issue, but directed towards having a system leak. Both of these faults effects the emissions of your vehicle. This repair may also apply to other engines and models as well.

How to get the trouble code on a 1997 Dakota?

How to get the codes on a 1997 Dakota: Put the key in your ignition and turn it to the “on” position three times. (Insert key, on, off, on, off, on). Leave it in the on position. The first trouble code will be displayed on your digital LED odometer.

How much does it cost to repair a p0743 Dodge?

The cost of diagnosing the P0743 DODGE code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

What are the trouble codes on a Dodge?

1 Dodge Codes 2 Trouble Code 3 P0171 4 P0300 5 P0301 6 P0340 7 P0420 8 P1000 – P1099 (Fuel and air metering and auxiliary emission control) 9 P1200 – P1299 (Fuel and air metering – injector circuit) 10 P1300 – P1399 (Ignition system or misfire)

When to use lock up on Nissan p0744?

Lock-up operation, however, is prohibited when A/T fluid temperature is too low. When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

Is there a problem with the p0748 OBD-II trouble code?