How to reset the service engine light on Dodge Grand Caravan?
How to reset the service engine light on Dodge Grand Caravan?
How to Reset the “Service Engine Soon” Light on a Dodge Grand Caravan Release and raise the hood. Identify the battery, which is located on your right side when facing the Caravan. Locate the two cables on top of the battery. The negative cable will be black and has a minus symbol to indicate its polarity.
What causes the service engine light on a Dodge Ram?
The Dodge Ram has a sensor that measures fuel emissions. If the computer misreads the emissions from the gas cap, it generates a code. After you remove and reattach the gas cap, remove the negative battery cable and repeat Step 1.
How do you reset the ECU on a caravan?
Wait at least 15 minutes, then replace the negative terminal, tightening the nut firmly. Close the hood, and start the Caravan. The ECU, along with the Service Engine Soon light, have both been reset.
What to do when service engine light does not come back on?
If the code does not come back on, the issue was intermittent. If the code returns, move to the next step. Remove the gas cap and put it back on, making sure that it’s tight. The Dodge Ram has a sensor that measures fuel emissions. If the computer misreads the emissions from the gas cap, it generates a code.
Why is my computer not working on my Dodge Grand Caravan?
Sometimes the cause of the error can be as simple as tightening a loose gas cap. In order to verify that the cause of the problem has been fixed, the computer on your Grand Caravan will need to be reset. This process is simple and takes less than 10 minutes.
How to disconnect the battery on a Dodge Grand Caravan?
Disconnecting the battery can be done even if the driver is a complete and utter novice at car maintenance as all that’s needed is a little knowhow and an adjustable wrench to deal with any troublesome bolts. Start by opening up the hood of the vehicle and making sure that it’s secured.
How can I Reset my Dodge Grand Caravan?
Fully depress the GAS PEDAL slowly three times within 10 seconds Make sure to depress the pedal all the way down. Turn the ignition off and start the engine to verify the indicator has been reset. Repeat this procedure, if the message still illuminates when you start the engine.
Why is the Check Engine light on on my Dodge Grand Caravan?
If you’re having trouble turning off the check engine light on your Dodge Grand Caravan, there’s no need to worry. Sometimes this light can stay illuminated even if there’s nothing wrong with the engine, but either way, learning how to turn it off is important.
What does the computer do on a Dodge Grand Caravan?
The Dodge Grand Caravan PCM, or powertrain control module,is the computer that controls everything from the fuel mixture to the emissions regulation system.
Where is the negative battery on a Dodge Grand Caravan?
The driver’s side compartment just above the front wheel is where it can be found on a Dodge Grand Caravan. There should be a bolt on the negative battery cable. This has to be loosened with the adjustable wrench. Don’t remove it. The negative battery cable itself should be detached from the terminal post.
How to Reset the “Service Engine Soon” Light on a Dodge Grand Caravan Release and raise the hood. Identify the battery, which is located on your right side when facing the Caravan. Locate the two cables on top of the battery. The negative cable will be black and has a minus symbol to indicate its polarity.
Wait at least 15 minutes, then replace the negative terminal, tightening the nut firmly. Close the hood, and start the Caravan. The ECU, along with the Service Engine Soon light, have both been reset.
If the code does not come back on, the issue was intermittent. If the code returns, move to the next step. Remove the gas cap and put it back on, making sure that it’s tight. The Dodge Ram has a sensor that measures fuel emissions. If the computer misreads the emissions from the gas cap, it generates a code.
The Dodge Ram has a sensor that measures fuel emissions. If the computer misreads the emissions from the gas cap, it generates a code. After you remove and reattach the gas cap, remove the negative battery cable and repeat Step 1.
