How do you Bleed the brakes on a Chevy Silverado?

Close the screw, then bleed both front brakes starting with the right one first. After checking for a firm pedal, drive the vehicle above three miles per hour. The controller will automatically reset the system by commanding the rear motor to run to the home position.

What kind of brakes does a Chevy Silverado have?

The modulator assembly has fluid chambers for all four brakes, two isolation solenoid valves, four check balls, a motor pack containing three bidirectional direct current motors with electromagnetic brakes (EMBs) and/or expansion spring brakes (ESBs), three ball screw assemblies, four pistons, a gear drive set and gear cover.

How do you turn off the brake light on a Chevy Silverado?

The only way to turn the brake light off is to restore proper line pressure to both brake circuits when the pedal is pushed. If your Silverado is having trouble stopping, or noticeably leaking fluid, don’t drive it. Just have it towed to a mechanic.

Why are the brakes soft on my Chevy Silverado?

Air trapped in the lines, calipers or wheel cylinders will make the pedal feel soft and spongy. Air is compressible, so when the brakes are applied any air bubbles in the system must first be compressed before the hydraulic fluid will transmit pressure to apply the brakes.

Is it possible to bleed the brake system?

Bleeding the brake system after changing the brakes can be hard on some anti-lock braking systems. The good news is that on some GM vehicles, a scan tool isn’t needed to bleed ABS brakes.

What’s the best way to bleed brake fluid?

There are only two methods left: The first is to use one of the pricey brake bleeding tools that literally pumps brake fluid backwards through the system to force the air bubble into the brake fluid reservoir. Get that special bleeder kit on ebay (below).

How to bleed GM ABS brakes with scan tool?

Scan Tool. 1 Step 1. Attach a pressure bleeder to the master cylinder reservoir and turn the ignition key to the On position. Pressurize the system to 35 pounds 2 Step 2. 3 Step 3.

Can You Bleed the brakes on a GM car?

Bleeding the brake system after changing the brakes can be hard on some anti-lock braking systems. The good news is that on some GM vehicles, a scan tool isn’t needed to bleed ABS brakes. A scan tool is only needed with a DBC-7 anti-lock braking system, and then only if air entered the ABS modulator during brake

How does the Brake bleeding sequence really matter?

If you start with the wheel closest to the master cylinder and bleed it until there is no air, and then move on to the wheel furthest from the master cylinder (just as an example), as you’re pumping the air out of that longest branch you could realistically get more air bubbles in the shortest branch.

What do you need to know about bleeding ABS brakes?

Here’s what you need to know about Bleeding ABS brakes. ABS systems are VERY sensitive to air bubbles. You know that air rises in the system. Once a bubble gets into the ABS valves, it’s almost impossible to suck it back down even with a hand-held vacuum pump. It’s definitely impossible to do it just by pumping the brake pedal.

What happens when you bleed the brake pedal?

Bleed the brake on the opposite end next (the left front if you started with the right front). Test the brake pedal after all the brakes are bled. Once you are certain of a firm pedal, drive the vehicle at more than three miles per hour so the controller can automatically reset the system.

How do you Bleed the brakes on a Delco VI?

The sequence on most of the FWD models using the Delco VI is RR,LR,RF,LF. Bleed the system using the appropriate sequence. Once the wheels are bled bleed the modulator. Start with the rear bleeder valve. Once the air has been removed, repeat the process with the front bleeder on the modulator.

When to bleed the rwal system on a Chevy 1500?

The RWAL system should be bled any time a line is removed or after replacing any brake line components. Park the Chevrolet on a completely level driveway or surface. Open the hood of the 1500. Check the level in the brake fluid reservoir and fill it to the “Full” mark on the side, if needed.

What kind of brakes did a 1989 Chevy Silverado have?

The 1989 Chevrolet C/K 1500 was equipped with rear wheel antilock brakes, commonly known as RWAL. The antilock brake system or ABS require a primary and secondary bleeding to remove all air from the system.

How do you Bleed the brakes on a Silverado?

Place your drip pan beneath the passenger front caliper. Open the bleeder screw on the caliper with an open-end wrench and allow the combination of brake fluid and air to escape. Close the bleeder screw and instruct your assistant to release the brake pedal.

How to bleed the rear brakes on a C / K 1500?

Once you are certain of a firm pedal, drive the vehicle at more than three miles per hour so the controller can automatically reset the system. Stop the vehicle afterward and bleed the rear brakes. Scan Tool Attach a pressure bleeder to the master cylinder reservoir and turn the ignition key to the On position.

Where is The Bleeder on a 1989 Silverado?

Place a drip pan beneath the passenger rear brake assembly. Open the bleeder screw on the passenger rear brake assembly with an open-end wrench. Allow the combination of brake fluid and air to leave the system and enter the drip pan. Close the bleeder screw and instruct your assistant to release the brake pedal.

What to do if your Chevy Silverado has 4 wheel drive?

If you have a 2008 Chevy Silverado with 4-wheel drive problems, or a similar GMC or Chevy truck from another model year, replacing the switch will solve the issue. You can purchase a new switch for around $30 and install it fairly easily.

What are the RPMs of a Silverado truck?

alkaspeltzar wrote: Hey guys, my 2010 5.3 AFM Silverado w/66,000miles has been RPM surging while driving over the past couple weeks. It seems to happen primarily when traveling between 45-55mph. When driving, slightly accerating, the truck is doing about 1100 rpm in its 6th gear. The engines RPMs seem to bounce back and forth 50-100 rpm.

What happens when one brake is stuck on a Chevy Silverado?

Pulling to one side – When one brake is stuck (particularly a front brake) the whole vehicle will pull in the direction of the bad brake. So if it is on the passenger side, your Silverado will feel like it is steering in that direction.

Can a brake caliper stick on a Chevy Silverado?

Your Chevy Silverado’s braking system is the most important safety feature on the vehicle. If it does not work properly, it can put you in a situation where you can be injured or killed. There are quite a few different situations that can cause a caliper to stick.

What causes brake fluid to go down in a Chevy?

Even with proper maintenance, you may find yourself with an unexpected brake problem — here are some of the most common examples. Low Brake Fluid: Your Chevy may develop a leak in the system that will result in the fluid level going down.

Why does my Chevy Silverado shake all the time?

Other theories focus on U-bolts, adding engine mount shims, checking the exhaust back-pressure valve and replacing the rear axle. On March 30, 2016, a dealer reported a 2016 Chevy Silverado 1500 with a similar vibration issue (NHTSA No. 10852511), saying the truck “has the Chevy shakes between 38 and 70 miles per hour.

Is there a bleeder valve for ABS brakes?

The modulator assembly uses solenoids for each brake circuit, but there are no special bleeder valves or special scan tool bleed procedure. So the brakes can be bled conventionally. The sequence if right rear, left rear, right front and left front.

How do you Bleed the brakes on a 2006 Chevy Fixya?

Bleed the wheels in the order of the longest brake line first and then working towards the shortest brake line. Refill the master cylinder reservoir before beginning each new wheel. Once the rear brakes are finished, lower the car and jack up the front of the car.

Where is the bleed screw in the brake caliper?

The bleed screw is located in brake caliper behind the wheel. It, therefore, resides in a challenging environment. It is disposed to heat from the braking process as well as dust and mud from the wheels. This harsh environment might cause the bleed screws to rust or corrode, making it difficult to remove them.

What causes no brake fluid to come out when bleeding?

Flex hoses deliver brake fluid from reservoir and brake master/cylinder to the brake caliper. In case the hoses happen to have any cut, or it’s torn out, there will be no pressure in the brakes; thus, brake bleeding will fail. It also causes the brake fluid to leak.

How do you Bleed the brakes on a Chevy Silverado?