How do you change the brake pads on a Chevy Silverado?

After all of the brake pads, caliper, and rotors have been replaced, you will need to bleed the braking system. Additionally, before driving the truck, pump the brake pedal a few times. Since you retracted the piston, it is not in direct contact with the brake pads, so pumping the brakes will ensure that the piston extends to the pads.

Where are the brake caliper mounts on a Chevy Silverado?

(Related Article: How to Jack Up Your Truck – ChevroletForum.com) Remove the two 19mm brake caliper mounting bolts holding the brake caliper to the bracket. These bolts can be found behind the bracket through the little rubber boots. Pull the caliper away from the rotor. Use a bungee cord to hang the caliper, so the brake lines do not get torn.

How do you remove a 19mm brake caliper?

Remove the two 19mm brake caliper mounting bolts holding the brake caliper to the bracket. These bolts can be found behind the bracket through the little rubber boots. Pull the caliper away from the rotor. Use a bungee cord to hang the caliper, so the brake lines do not get torn.

How can I tell if my Chevy Silverado brakes are due for change?

Installed brake pads, calipers and rotors on Chevy Silverado. You can verify whether your brakes are due for a change by first checking the brake pad thickness. Start by removing the wheel and looking at the brake pads from the top. There should be a piece of metal that extends from the pad and points towards the rotor.

What do I need to change my front brake pads?

To compress the front caliper piston, you will need a brake caliper compression tool, old brake pad, 10mm socket wrench, brake bleed kit, and drain pan. After compressing the front caliper piston, in this step, all you have to do is to remove old pads and hardware from the vehicle.

How do you replace the brake pads on a Chevy Silverado?

To reset your caliper pistons, you want to put a brake pad in front of the pistons and twist the large C-clamp until it pushes the pistons in. Push your brake pads back into place and put your caliper back down into place and replace those two 12mm bolts. We’ll fast forward as Don does this and tightens them up.

How can I tell if my brake pads are due to be replaced?

What’s the best way to remove a brake rotor?

Use a rubber mallet to hit the back and front face of the rotor. Spin the rotor as you do in order to evenly knock the rotor loose. Then simply slide the rotor off of the wheel studs. Figure 7. Hit the brake rotor with a rubber mallet.

How to remove rear rotors on Silverado 3500HD?

We tried to find a service manual for the truck (2008 Chevrolet Silverado 3500HD 6.6L duramax diesel dually) with no luck. ANY help on removing the rotors to be replaced OR finding a service manual for the truck would help so much!

Why are the brake pads on my Silverado not working?

I just replaced all of the brake pads on my 2003 Silverado extended cab 5.3L V8 4WD, and afterward I noticed that I could smell the right rear brakes cooking. Upon further inspection I found that the calipers are not releasing the rotor, the problem is present on both sides of the rear brakes, but more prevalent on the passenger side.

Why are my rear brake rotors not releasing?

Upon further inspection I found that the calipers are not releasing the rotor, the problem is present on both sides of the rear brakes, but more prevalent on the passenger side. When the caliper is squeezed using a c-clamp, and the bleed screw is opened I am able to rotate the rotor/wheel hub w/o any problem so it is not a wheel bearing.

Do you have to remove rear axle on Silverado?

You might be able to back off the shoes if there is a adjustment hole with a plug in the backing plate. There is NO need to remove the axle unless the seal is leaking.

How much does it cost to change brake pads on a GMC Sierra?

I recently changed my rear brake Pads on my 2001 GMC Sierra. The mechanic at the oil change station suggested that I install new 2 Rotor’s, and 2 new Calipers, along with the Pads. He said 90% of the time, the calipers stick on these trucks after the pads are changed. He wanted to charge me $532.00.

How are brake pads installed on a car?

The calipers use hydraulic pressure from the brake fluid to squeeze the brake pads against the rotors. Rotors are installed on the wheel hub and rotate as the wheel spins while providing a contact surface for the brake pads. As with any moving part, the rotors or calipers can wear out over time and need to be replaced.

What do I need to replace my Silverado caliper?

1. With the caliper came a few replacement parts. Inside were two bolts or slide pins as I believe they are called, a washer for the brake line, two rubber boots for the mounting bracket and two black rubber tubes that are about 2 inches long or slightly smaller. My uncle performed this work, I watched, helped and learned.

How do you change the front rotors on a Chevy Silverado?

Push the new rotor on the hub and clean it with brake cleaner or a solvent to remove the protective coating. Install all parts in reverse order of removal. Start the truck and pump the brakes slowly until the front brakes adjust and the pedal comes up to normal height.

Where can I buy brake rotors for a Chevy Silverado?

Buy Online. Pick Up In-Store. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only You depend on your Chevrolet Silverado to get the toughest jobs done, even in the most challenging conditions. Maintain the superior functioning of your braking system by swapping out your old Chevrolet Silverado brake rotors for new ones with AutoZone.

How do you change the brake pads on a Chevy Silverado?