Can you replace a power steering pump on a Dodge Stratus?

If you are installing a new or rebuilt power steering pump on your Dodge Stratus, you might need to transfer the pump pulley from the old unit onto the new one. You can replace it using a pulley puller, which you can rent at an auto parts store. Check at your local auto parts outlet before removing the pump.

How to adjust and replace a power steering drive belt?

Ease the belt onto the pulley. Never try to lever off the old belt, you may damage the pulley. Slacken the adjuster and pivot bolts, and push the pump inwards by the cast front plate until the belt is slack enough to ease off. Do not push against any other part of the pump or pipework, or you may damage it. Remove the old belt.

How do you replace a power steering pump?

You can replace it using a pulley puller, which you can rent at an auto parts store. Check at your local auto parts outlet before removing the pump. Remove as much power steering fluid as you can the steering pump reservoir using a hand siphon pump, then disconnect the black negative battery cable from the left strut tower-driver side.

How do you replace a power steering pulley?

Use a ratchet and socket with an extension to remove the bolt through the hole for the speed sensor wiring. Remove the drive belt from the power steering pulley and lift the steering pump and bracket from the engine compartment. Install the pump bracket on the new unit if necessary and set the new steering pump in place.

How do you replace a power steering bracket?

Remove the drive belt from the power steering pulley and lift the steering pump and bracket from the engine compartment. Install the pump bracket on the new unit if necessary and set the new steering pump in place. Install the power steering adjusting bolt, pump top bolt and the bolt attaching the pump bracket to its mounting bracket on the engine.

How to install a new steering pump pulley?

Install the inlet hose and outlet pressure hose using a new O-ring on the hose connector of the pressure hose. Install the drive belt on the steering pump pulley. Adjust the belt tension by swiveling the pump and tightening the adjusting and mounting bolts. Tighten the bolts to 40-foot lbs (54Nm.)

How do you remove a steering pump from a car?

Remove the front bracket bolt that secures the pump to the mounting bracket. Use a ratchet and socket with an extension to remove the bolt through the hole for the speed sensor wiring. Remove the drive belt from the power steering pulley and lift the steering pump and bracket from the engine compartment.

How do you replace a tire on a Stratus?

Replace the insulator grommet from the ground cable on the strut tower to prevent an accidental ground. Loosen the wheel lugs from the tire on the passenger side of your Stratus. Raise the right side of the vehicle using a floor jack; safely support it on a jack stand and remove the tire.

How do you remove splash shield from Stratus?

Loosen the wheel lugs from the tire on the passenger side of your Stratus. Raise the right side of the vehicle using a floor jack; safely support it on a jack stand and remove the tire. Remove the splash shield by pulling on the plastic clips or unscrewing the bolts with a wrench or ratchet and socket.

How do you add steering fluid to the reservoir?

Turn on the engine and fully turn the steering wheel to the left and right. Add steering fluid to the reservoir as needed and a little at a time, until the reservoir maintains the fluid level. Since 2003 Dan Ferrell has contributed general and consumer-oriented news to television and the Web.

How to remove the steering column from a Dodge Ram?

Dodge ram steering column removal and dollar saving tips!!! Step-by-step DIY repair for $50!!!!! – YouTube If playback doesn’t begin shortly, try restarting your device.

How do you get a steering column in a front wheel drive car?

You may have to move the steering wheel to access the bolt. Sometimes this is outside, or inside the vehicle. On many front wheel drive cars with rack and pinion steering, this means dropping the engine cradle 4 inches (10.2 cm) to access it. You may have to peel back a rubber boot to access this as well.

What should I do if my steering column locks?

Remove the steel backing behind the knee bolster. These are usually held on by several bolts. Make sure the front wheels are pointed straight ahead, but do not lock the ignition if it locks the steering column. Loop the seatbelt through the steering wheel instead.

What do I need to install power steering?

Install the power steering adjusting bolt, pump top bolt and the bolt attaching the pump bracket to its mounting bracket on the engine. Do not tighten the bolts yet. Install the inlet hose and outlet pressure hose using a new O-ring on the hose connector of the pressure hose. Install the drive belt on the steering pump pulley.

What to do if your steering pump goes bad?

Remove as much power steering fluid as you can the steering pump reservoir using a hand siphon pump, then disconnect the black negative battery cable from the left strut tower-driver side. Replace the insulator grommet from the ground cable on the strut tower to prevent an accidental ground.

How do you install a new steering pump?

Install the pump bracket on the new unit if necessary and set the new steering pump in place. Install the power steering adjusting bolt, pump top bolt and the bolt attaching the pump bracket to its mounting bracket on the engine. Do not tighten the bolts yet.

What’s the best way to Prime an oil pump?

The first method is to pack the oil pump full of Vaseline. Vaseline will create the seal needed for vacuum to draw in oil. The Vaseline will then be quickly dissolved into the oil.

How do you seal a new oil pump?

There are two easy methods of insuring the oil pump will create the seal needed to pull oil in on initial start up. The first method is to pack the oil pump full of Vaseline. Vaseline will create the seal needed for vacuum to draw in oil. The Vaseline will then be quickly dissolved into the oil.

How do you remove pressure hose from steering pump?

Place a drain pan underneath the vehicle in the direction of the steering pump. Disconnect the pressure hose at the steering pump and remove the hose connection using a wrench or tube wrench to avoid damage to the line and nut. Discard the O-ring from the connector and then disconnect the inlet hose by removing the hose clamp.

How to change a leaking power steering hose high?

After you have found the leak and know you need to change your power steering pressure hose here are the steps. 7) Check how hose is attached, so the new one goes on the same. 12) Top off power steering fluid to cold line. 13) Next time you drive check the fluid level again. Virtually the same steps for any make of vehicle.

How do you remove a power steering pump?

The pulley is flush with the end of the pulley shaft. Grab your power steering pump removal tool, and position the fingers onto the edge of the pulley with the correctly sized rod (if needed) installed to remove the pulley. Keep turning the bolt until the pulley slides off the shaft. Figure 5. Removing the pulley from the pump.

How do you change power steering pump on Dodge Caravan?

Take the pump and pulley assembly over the aluminum bracket and out of the engine. Install the new pump on its bracket and torque the front mounting bolts to 40 foot-pounds. Install and torque the rear mounting bolt and spacer to 40 foot-pounds. Reinstall the pressure and supply hoses.

How do you change the power steering pump?

Insert the feed and return lines into the new pump and tighten down the compression fittings with the appropriate wrench. Fill the pump with new power steering fluid. The pump will fill the feed and return lines with fresh fluid once the engine is turned on, so start the vehicle and move the steering wheel one full turn in each direction.

What happens when a power steering pump fails?

Power steering pumps continuously turn as the engine is operating to keep a pressurized supply of fluid available at the steering rack. Power steering pump failures happen, and when they do, your stuck cranking the wheel with two hands until a new pump is installed. This article applies to the Dodge Ram 2nd Generation (1994-2001).

How does a power steering pump work on a Dodge Ram?

There are two lines connected to the power steering pump. The upper line is the return, and a squeeze clamp secures the rubber portion of the line to the hard portion. While squeezing the clamp, pull the line and twist the rubber line off the hard line.

How does the power steering work on a Dodge Caravan?

The engine on your Dodge Caravan drives the pump on the power steering system to assist you every time you want to steer the vehicle left or right. When power pump components wear out or develop leaks, you might experience hard steering.

How do you adjust power steering belt tension?

Adjust the power steering belt tension by inserting the ½ inch drive adapter in the square opening on the bracket and pushing down. Tighten all of the pivot and tensioner bolts to 40 foot-pounds by turning them clockwise with the ratchet and the socket. Lower the jack and pull it out from under the car.

Can you replace a power steering pump on a Dodge Stratus?