Why is my gauge cluster not working on my Dodge Ram?

Without going into detail, which is somewhat extensive, the problem is a short in the signal between the ECU and the gauge cluster along the BUS line. It could be anything from a faulty module (wiper timer, air bag, radio) to a blown fuse, a bad wire or even a fault within the cluster or ECU itself. Honestly, all I can say is good luck.

Why does my Ram 1500 not start up?

Turn the key, gauges radio everything but the starter comes on. The trick I found I’d if I hold the ignition switch to the starting position, 15, 30, a minute, sometimes longer, it’ll finally crank over and start. Not sure what’s causing this.

Is there a problem with the ignition switch on a Dodge Ram?

Seems to be an ongoing issue with the same defective ignition switch in these vehicles as the Ford, Honda, Acura, Lexus, Toyota, and Infinity that all use the same bad parts. Change the ignition switch and consider yourself lucky you didn’t get cheated by crooked dealerships and dishonest manufacturers. 58 people found this helpful.

Are there any problems with the Dodge Ram 1500?

Definitely not the starter.. Known to be problems with these Ram 1500 are faulty ignition switches that burn out but not completely so they work intermediately. if you have enough juice in your battery to run all your lights and accessories then the starter would make at least a half-assed attempt..

Why are all of the gauges in my car not working?

There are a lot of different types of instrument cluster designs and configurations, but when all of the gauges in a car stop working at once, the problem is usually either a fuse or wiring problem. The first step in diagnosing this type of issue is to identify the fuse associated with the instrument cluster or gauges.

Why does the light go out on my Turn signal?

Some bulbs may go out when the brake pedal is depressed, or some may get brighter that should not. Also, a defective turn signal switch and/or an ungrounded steering column may be the cause of these conditions. A thickly-applied interior paint job may cause a poor ground, not just no ground.

Why does my car gauge read cold when I Turn on the ignition?

With the ignition on, the gauge should register cold. If you connect the sending unit wire to ground, the gauge should switch to read hot. If the gauge moves as expected, then you can suspect a bad sending unit. If the gauge doesn’t move when you ground out the sensor wire, then you can suspect a bad gauge.

Why is my front Wiper not working on my Dodge?

If the SCM detects no inputs from the right multi-function switch, it transmits an electronic Signal Not Available status message over the LIN data bus. The SNA status signals the Instrument Cluster to request other electronic modules to implement a fail-safe mode of operation for the front and rear wiper systems.

Why are my turn signals not working on my Dodge Ram?

Awesome – thanks, this worked on my 2010 Ram. So strange I was driving back from Flagstaff, AZ and just went to turn High Beams on and they didn’t work and wipers went on. Tried to get over, no turn signals. Someone else mentioned a bad harness, didn’t want to take apart dash.

Why are my lights and wipers not turning off?

Your lights and wipers on and you can not turn on/off is a failsafe feature. This indicates a problem with the control stalk and/or computer communications. Here are a couple compiled excerpts from the SM.

Why is my speed ODM gauge not working?

The cause of problem: bad connection under fuse box going to hazard circuit. The connection plug pins had some corrosion on them. This allowed voltage to travel through that circuit but not enough current.

What should I do if my gauges go out?

I’ve had my gauges go out with the “no bus’ message in the odometer window three times now! Checked all the fused, disconnected the battery, to no avail…..Sound firmilliar?

Why are the fuel gages on my Dodge truck not working?

Next I pulled up the 1/16 inch on the connector and while I didn’t loose all the gages this time the oil temp and fuel gages dropped to zero! I found that the PCM wire bundle is putting pressure on this connecton against a poorly designed draw down bolt that caused the contacts to become disconnected.

What to do if your instrument cluster is not working?

Try the following, just to rule out a failure on either module… Testing the instrument cluster: (Start with the key in the OFF position.) -Push and hold the trip/reset button on the instrument cluster. -Turn the key to RUN (Do not start the engine.) while you are still holding the button.

Why does my Dodge Ram engine not crank?

Okay, so if your Dodge Ram engine will not crank, check for one OR MORE of the following possible malfunctions. 1. Weak or dead battery – Charge or replace the battery if necessary. If the battery is good but it keeps going dead then you need to check or test the charging system.

What to do if your dash light does not work?

#Test the dashboard light bulbs. If the fuses are working properly, check for a blown bulb in the dashboard. Following the manufacturer’s instructions, disconnect the battery while working on the dash, remove the faceplate covering your vehicle’s dashboard gauge panel. Remove the screws holding the plate on. Carefully remove the faceplate.

Where is the control switch for the dashboard lights?

Most vehicles have a dashboard lights control switch that will dim the dashboard lights, as well as turn them off. Check the control switch, which should be located on the console near the steering column or part of the headlight switch. [ [Image:Fix Dashboard Lights That Won’t Light Step 1 Version 3.jpg|center]]

How can i dim the lights on my dashboard?

Begin the process by trying the simplest of solutions first. Most vehicles have a dashboard lights control switch that will dim the dashboard lights, as well as turn them off. Check the control switch, which should be located on the console near the steering column or part of the headlight switch.

Where is the fuse on the dash light?

The fuse box may be under the hood, or near the floor, near the brake pedal, or there may be two fuse boxes in both places. Refer to the diagram on the fuse box cover to locate the correct fuse. Replace the dashboard light fuse if necessary. Note: also check if the tail lights are working.

What is the problem with my Dodge Ram?

Not open for further replies. I have a 2004 dodge ram with a problem. While driving the oil pressure gauge drops suddenly and the check gauges light illuminates. If I pull over and turn the the truck off then back on, it’s fine. Sometimes it will keep doing it, sometimes it wont.

What did the check gauge light come on on my Dodge Ram?

My 2004 5.7 Hemi Today the check gage light came on and the oil PSI fell down to zero when I turned a cornner. It was one quart low so I added one quart of oil and it seems fine now. Just sharing.

When do the gauges go off on a Dodge Ram?

Gauges go off & on when 2003 Dodoge 2500 truck hits a bump. Also NOBUS light comes on. Headlights come on also.

Why is the Check Engine light on on my Ram 1500?

One simple reason is that your gas cap isn’t secured tightly in place, or your RAM 1500 has a dysfunctional solenoid (the component connecting the car battery to the ignition switch). In any case, if your RAM 1500’s check engine light is on, you don’t want to just reset it. You’ll want to first determine what’s going on.

What kind of truck has no bus gauges?

I have a 2000 ram 1500 2X with the 5.9 automatic, however I believe that this is applies to all gen2 trucks regardless of drivetrain or engine type. My Story… See the end to get straight to my find. I’ve had my gauges go out with the “no bus’ message in the odometer window three times now!

Where is the negative wire on a Dodge Ram?

If it reads full all the time, and again both of the others are good, check the negative wire. Both run in the harness under the truck on the drivers side, going through the plug that is directly behind the inner fender well on the drivers front.

Why is my dad’s fuel gauge not working?

Discussion in ‘ Audio & Electronics ‘ started by BlackMagnum2000, Sep 9, 2015 . Hey guys, hoping you can help me out here. Trying to figure out why my dads fuel gauge isn’t working. 2006 2500 Cummins. Got a Fass pump on it. Just put a brand new sending unit it in. When we got the truck, it was intermittent.

Why is my gauge cluster not working on my Dodge Ram?