Can a CV axle be removed from a stub shaft?

Assuming that you can remove the CV axle, and the stub shaft stays attached to the axle (it has the two times I’ve done it on my car), then you shouldn’t need any special tools to remove and replace the large main seal that is pressed into the case.

What is a CV axle in a car?

What is a CV axle? It’s a shaft with constant-velocity (CV) joints that transfers the rotating torque to one of the drive wheels in a car. It might also be called a half shaft or drive shaft. A typical front-wheel drive car has two CV axles (CV shafts), one at each front wheel.

How to replace an automotive CV axle-2carpros?

Reinstall the CV Axle Nut Reinstall the CV joint axle nut by hand to avoid cross threading and then tighten to manufactures specification with is usually between 120 and 140 foot pounds for torque. Install a new cotter pin and then bend one end if it over the axle threads to hold it in place while cutting off any excess and you are all set.

How do you remove axle nut from CV?

Remove the Axle Nut Cotter Pin On most car’s there will be a cotter pin that secures the outer axle nut from coming off of the CV joint. Use a pair of side cutters (dikes) to remove the cotter pin from the axle snout. There might also be a star wheel which can be removed after the cotter pin. 2. Remove the Axle Nut

What is the ring at the end of the CV axle called?

Answer: It’s commonly referred to as a retaining ring; not a snap ring. The ring at the end of the inner CV axle joint, is compressed by applying pressure on the joint shaft when the shaft is being pushed into the transmission.

How long does it take to replace a cv shaft?

Removal of the hose should not take more than 5 minutes. *Note: Before putting the hose back on, clean the throttle body plate with some carburetor cleaner solvent. Rotate the axle shaft until one of the lips or ears on the CV bearing cup is pointing up. The transmission must be in neutral to rotate the shaft.

What to do if your CX axle shaft is stuck?

CX AXLE SHAFT STUCK – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

How to replace intermediate stub shaft on Dodge Ram 1500?

To avoid this, cancel and sign in to YouTube on your computer. I’m an Automotive and Heavy Duty Mechanic/ “Jack of All Trades” that likes to make videos about anything and everything of interest.

How big is the inner stub shaft on a Malibu?

I am replacing the passenger side drive shaft on a 2002 Malibu. The new axle came with the inner/outer cv joints, as expected. But, when i removed the old axle there is a short 6-8″ section on the transaxle end of the axle that DID NOT come with the new part.

How do you remove seal from Chevy Malibu stub shaft?

There is a second tool that is used to remove the seal from the stub shaft (or from the fixed shaft on the drivers side). The tool works like a standard puller. The tool grabs the back of the seal, and the puller pushes against the end of the shaft, pulling the seal off of the shaft.

How to successfully remove a stuck inner CV joint?

How to successfully remove a stuck inner CV joint. – YouTube How to successfully remove a stuck inner CV joint. If playback doesn’t begin shortly, try restarting your device.

Can a CV joint be replaced at a parts store?

You’d then replace it and the boot, lubricate the new and old joint with fresh grease, reinstall and go. Nowadays it’s difficult to find a CV joint for sale at a parts store. The industry has made it standard procedure to swap in a complete new or remanufactured axle, with the boots installed and prelubricated.

What to do if your CV axle is not catching?

Jack up your vehicle and put on the parking brake. Rotate your front tires forwards or backwards and if you hearing grinding and/or clicking, and the CV joint is not catching, most likely the one that needs replacement will be there.

Where is the outer tie rod on a CV axle?

Unbolt the outer tie rod from steering knuckle. The outer tie rod is literally a rod bolted to the steering knuckle, which is just behind the rotor. This piece will likely be bolted with another 17mm bolt. Like the axle nut, this bolt may be held in place with a cotter pin. Penetrating lubricant may help you more easily remove the pin and bolt.

What to look for in an inner CV joint?

Look for cracking and splitting around the rubber CV joint boot, and look for evidence of fresh, excess grease on the transmission, cross-member or suspension components around the joint. Grasp the axle shaft as close to the inner CV joint as possible and try to push it back and forth.

How to pay for CV axles and parts?

CV Axles & Parts: Advance Auto Parts has the parts you need at great prices. Felpro High Perf. (1) No Interest if paid in full in 6 months on purchases of $99+ Check out with PayPal Credit Subject to credit approval. See terms. Not finding what you need?

Can a wheel angle affect a CV joint?

If the wheel angle doesn’t noticeably affect the CV joint sound, then it’s the inner joint. Confirm your diagnosis by crawling under the car and manually checking the CV joint.

How do you get a stub shaft out of a Chevy Malibu?

A simple tug on the slide hammer, and the stub shaft should pop right out of the end of the axle. I’ll follow with other posts to attach the picture of the seal installer tool.

How to remove right side half shaft on a Honda Pilot?

When one of these boots tears or the CV joint needs service, then the entire half shaft assembly has to be removed. If the right side half shaft on your Honda Pilot needs to be removed, then you can do so in about an hour. Lift the front of the Honda Pilot using a floor jack.

Can a CV axle be removed from a stub shaft?