How to test ignition a on a 2004 Silverado?
How to test ignition a on a 2004 Silverado?
See if you have 12 volts to the crank fuse when they turn the switch top the start position, make sure to have them turn the switch to start at leat 5 times with the samr test results. yes, i have 12v on both sides when key is in crank position. And you had 12 volts to fusese ign a and ign E correct? ignition e, yes. how do i test ignition a?
Why does my Chevy Trailblazer have a bad ignition switch?
Intermittent Bad Ignition Switch Causes Low Power and No Blower Motor. This 2004 Chevy Trailblazer came in with multiple concerns. The main issue was intermittent low power. When this happened, the customer said that the Electronic Throttle Control, ABS, Traction Control, and sometimes the 4WD lights would come on.
Where does the power from the ignition switch come from?
From the ignition switch, power feeds from the run position on circuit 300 which feeds the HVAC, 4WD, HVAC 1, Brake, and TBC Run fuses. Do you see the connection? With the ignition switch feed fuse IGN A good, the biggest common failure point would be the ignition switch.
Is there a 2004 Silverado that won’t start?
I have a 2004 silverado that won’t start. Have bench tested starter and battery and replaced relay and ignition switch. I have a 2004 silverado… I have a 2004 silverado that won’t start.
What is the ignition switch on a Chevy Silverado?
An ignition switch for Chevy Silverado 1500 is the part that sends the key signal to your vehicle’s starter relay. Dirty or failed contacts in this component mean your truck won’t be going far, so make moves when your truck’s on the ropes.
Where is the ignition switch on a 2003 Avalanche?
IGN A 40A Ignition Switch RUN. START. RUN/START/ACCY LBEC 1 50A FLASH Fuse, TBC 2A Fuse. TBC 2B Fuse. TBC 2C Fuse. LT DOORS Fuse LR PARK 10A Exterior Lamps-Left Rear. Clearance Lamps-Left TBC BATT 10A Body Control Module (BCM). PASS-Key Module AUX PWR 20A Accessory Power Outlets. Auxiliary Power Outlets PCM 1 15A Powertrain Control Module (PCM).
What are the fuses on a 2004 Chevy Silverado?
Repair Topics > Fuses > Chevrolet > 2004 Chevrolet Silverado… MBEC 1 50A SEAT CB. RT DOOR CB LBEC 2 50A LOCKS Fuse. DDM Fuse, PDM Fuse, ECC Fuse, AUX PWR 2 Fuse IGN A 40A Ignition Switch RUN. START. RUN/START/ACCY LBEC 1 50A FLASH Fuse, TBC 2A Fuse. TBC 2B Fuse.
How is the ignition switch connected to the car?
The ignition switch itself is connected to the ignition cylinder by a shaft or lever. Inside the ignition switch, several contacts connect vital electrical systems needed to start and run the car.
What happens when you turn off the ignition key?
When you switch off the ignition key, the ignition relay should also shut off power to all engine components; otherwise, it will drain the car battery when you let the car stands over the night. When the ignition relay fails, it can cause the ignition system to be activated constantly, even when you have removed the keys from the ignition.
What to do if your ignition cylinder is worn out?
How To Fix It: Fortunately, this is an easy fix. Just turn the wheel back and forth until the ignition cylinder is freed. It’s a fact of life that mechanical things tend to wear out, and the same goes for mechanical keys and key cylinders used in your car’s ignition system.
See if you have 12 volts to the crank fuse when they turn the switch top the start position, make sure to have them turn the switch to start at leat 5 times with the samr test results. yes, i have 12v on both sides when key is in crank position. And you had 12 volts to fusese ign a and ign E correct? ignition e, yes. how do i test ignition a?
Why does my Silverado ignition lock not turn?
There are two spring loaded pins, 180 degrees apart, that push in between tabs on the back of the key insert. Those pins appear to prevent the turn of the key because the tabs catch on them. Not sure what the problem is. My first guess is the tumbler, but I cannot turn the key to the run position to remove it. Any ideas?
I have a 2004 silverado that won’t start. Have bench tested starter and battery and replaced relay and ignition switch. I have a 2004 silverado… I have a 2004 silverado that won’t start.
How to remove the ignition switch without a key?
How to Remove the Ignition Switch Without a Key. 1 Step 1. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder. Be sure to make the hole large enough 2 Step 2. 3 Step 3.
