How do I read Trouble Codes on a 1993 Ford Ranger?

Look at the Ranger’s check engine light. It will blink multiple times and then stop. The light will flicker to give a warning that the test is beginning. A code will blink and then pause for two seconds, indicating that it is moving on to the next number in the code. After the code is finished, it will pause for four seconds.

Where are the plugs on a 1993 Ford Ranger?

Locate the two plugs required to perform the test on your Ranger. These are in the Ranger’s engine compartment on the driver’s side fender behind the air filter box. One is labeled the self test plug (STP) and is triangular-shaped with six pins. The other plug is labeled the self test input (STI).

When did the Ford Ranger get a V6?

The Ford Vulcan V6 is a 3.0L, 60° V6 engine, first introduced for the 1986 model year and originally designed to be the optional engine in the Ford Taurus and Mercury Sable. In 1991 it became available in the Ford Ranger where it replaced the Cologne 2.9 engine (which it is not related to) as the base V6 in the Ranger

What kind of fuel does a Ford Ranger use?

The engine was designed to use electronic fuel injection from the start (there was never a carburetor-equipped version), and was also sold in a “flexible fuel” configuration that could burn normal gasoline, E85 (a blend of 15% gasoline and 85% ethanol) or any mixture of these two fuels.

What does the Check Engine light mean on a Ranger?

What to do if your Ford Ranger wont start?

Put the vehicle in park and turn off the ignition. Raise the hood and locate the car battery. Place the adjustable wrench on the bolt securing the negative battery cable to the negative terminal on the car’s battery.

Where is the self test plug on a Ranger?

Are there any problems with the 2017 Ford Ranger?

M O T one month ago and service 3days ago… 2017 ford ranger 3.2 manual: Parking pilot isn’t working, ABS warning light is on, stability control malfunction light is on and also got ‘hill decent control malfunction’ warning, ‘hill start assist not available’ warning, ‘ESC Service Required’. All came on at the same time.

What is the Ford Ranger Anti theft system reset procedure?

Once it blinks start the engine and the vehicle will now be reset. If the engine does not start then You did not turn the key on and off quickly enough. The car is not starting. Flashing red light key shows that it is locked. How can we solve this? How to disconnect the slarm system.?

Is there a relock button on Ford Ranger?

You do not need to use the AS-BUILT data (nor modify it) if you use the GUI settings instead. They all exist unless otherwise noted. Enables 30 or 45 second auto relock if doors unlocked with keyfob but are not opened. Works with double-honk disabled NOTE: The button and dash indicators still function but do not do anything.

How to turn off stealth mode on Ford Ranger?

When you open the door the dome lights and stuff stays off instead of lighting up like the surface of the sun. When you open the door the dome lights and stuff stays off instead of lighting up like the surface of the sun. Click to expand… Also disables brake lights. Can’t have those coming on in stealth mode……

When does the theft light go out on a Ford Ranger?

Btw, the theft light is supposed to blink every 2 seconds when key is out (as deterrent to thieves) , and should go out after it starts or in the start position longer than 2 seconds. My light would blink with the key out, but when I was in the start position it would stay on solid. I could crank my engine (ree-ree-ree-ree) but it would not start.

What are the trouble codes on a Chevy truck?

Watch the “check engine” light. It will start flashing. Chevy trouble codes are two digits. The first digit will be represented by a long flash. Secondary digits will be relayed through quicker flashes. For example, trouble code 16 will be relayed with one long flash and six short ones. Write the codes down as the “check engine” light sends them.

How to run a diagnostic test on a 1993 Chevy truck?

They will be on the end of the row to the far right, and the will be side by side. Place your key into the Chevy’s ignition and turn it, but don’t crank the engine. Watch the “check engine” light. It will start flashing. Chevy trouble codes are two digits. The first digit will be represented by a long flash.

How to read codes from your check engine light?

That’s two clicks for Honda users. Wait a second and keep your eye on the check engine light. You should see it start to light up in a series of flashes. The light is blinking in a simple code of long and short. Long blinks mean “10” and short blinks mean “1”.

Why is my Check Engine light not working?

If the seller was worried that the car wouldn’t pass an emissions test, thus causing you to not want to buy it from them, they may have disable the ECM and prevented the vehicle from storing Check Engine Light Codes. Situations like this are rare – but it has happened.

How to read GM OBD diagnostic codes for free?

How to read the codes 1 Ground terminals A and B (see diagram below) with the ignition “ON” and engine not running. The system will enter the… 2 After Code 12 is displayed, any stored trouble codes will be displayed by flashing the “CHECK ENGINE”, “SERVICE… More

What is the code for service engine soon?

In this mode, the computer will display a Code 12, three consecutive times, by flashing the “CHECK ENGINE”, “SERVICE ENGINE SOON” or “MALFUNCTION INDICATOR LAMP” or light. A Code 12 consists of one flash, a short pause, then two flashes in rapid succession. 2.

What was the problem with my Ford Ranger?

My 2008 turbo Ranger just got wrtten off by insurance co after months of exhaustive independent engineer inspections after filling it with contaminated fuel at Woolworths /Caltex discount fuel. Just salvaged it as economic write-off from Pickles Auctions and would love to see link to the video you mention.

How long can a Ford Ranger go without a battery?

Sometimes the truck can go for a week without a problem and then you try to start it and it clicks twice like a dead battery and other times it keeps cranking and I let go of the key and cranks until I turn the switch back to the off position. I wait about 3-5 minutes and it starts right up.

What kind of problem does a 1985 Ford Ranger have?

1985 Ranger V6, 2brl carb, manual trans. has a chronic problem of stalling during slow down at turns and intersections. It will start right back up. It runs great except for the stalling and it burns a little oil.

What was the color of the 1993 Ford Ranger?

1993 Ford Ranger Splash in Torch Red with a Flint Gray interior. A carfax certified clean title vehicle with no accidents and no damage. All original and was the first year ford offered the splash edition with the stepside bed and splash decal.

Why is my Ford Ranger stalling and dying?

FOR THOSE WHO CARE CTC IS PROBABLY IN COMPARISON TO AUTOZONE BUT IS IN CANADA – NATION WIDE AND READY TO RIP YOU OFF!! The fact that it runs as long as you spray the Quick-Start shows the engine is not getting fuel. Either the computer is not firing the injectors or something is keeping the pressure in the rail way too low.

What kind of engine does a Ford Ranger have?

A Ranger that is driven roughly and used for a lot of hauling and towing may not last as long. Trucks that are cared for with routine maintenance should keep going for years. How many different engines has Ford used for Rangers? Ford has used a variety of I4, V6, and V8 motors for these vehicles over the years.

What are the firing orders on a Ford Ranger?

1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6 1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6

How to diagnose a 2.3L Ford Ranger misfire?

P0304 Cylinder #4 Misfire. The engine is suffering a bona-fide misfire condition, but no misfire codes are registered in the computer’s memory (if OBD II equipped). Lack of power upon acceleration. Smell of unburned gas exiting the tail pipe. Rough idle and may stall. Cranks but does not start. Will not pass the emissions tests. Bad gas mileage.

What’s the ignition system on a Ford Ranger?

Ignition System: In a nutshell, the ignition system on the 2.3L Ford Mustang or Ranger consists of 2 ignition coil packs, an externally mounted ignition control module (certain years), spark plugs, and spark plug wires. The majority of misfire conditions have their root cause here.

Why does my 2.3L Ford Ranger have one dead cylinder?

In other words: If the engine is misfiring, the engine is simply not firing on all cylinders. Now, since the 2.3L Ford engine is a four cylinder, having just one ‘dead’ cylinder will cause an impact on engine performance and you’re gonna’ definitely feel it as you’re driving down the road or stopped at a traffic signal.

Are there any problems with the Ford Ranger?

Ford Ranger owners have reported 26 problems related to check engine light on (under the engine and engine cooling category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Ford Ranger based on all problems reported for the Ranger.

What causes a flashing check engine light on a Ford Ranger?

While a majority of the time, the flashing check engine light is going to be caused by a misfire related to your Ranger’s ignition system or fuel system (as stated above), there are other issues that can cause it. Your timing chain could have jumped .

What causes a Ford Ranger engine to misfire?

Fuel Mixture: If the engine is running rich or lean, the engine will misfire and throw the fuel mixture related codes, such as P0171, P0172, etc.. Injector Issues: A bad fuel injector (s) can cause a misfire.

What causes a trouble code on a Ford Ranger?

Clearing trouble codes on a Ford Ranger is a simple and easy task that anyone can do. Trouble codes are set off by the truck’s computer when it detects a problem, which can be as simple as a loose gas cap, or as severe as an engine misfire.

Where is the self test plug on a 1993 Ford Ranger?

This plug is connected to an automotive code reader which informs the user of any problems with the vehicle. On older vehicles, such as the 1993 Ford Ranger, this procedure must be done manually. The user must locate the self test plugs and set the vehicle in test mode.

What is the code for Ford diagnostic trouble?

Refer to our Generic OBD II code list for definitions on all other Ford diagnostic trouble codes. P1000 OBD System Readiness Test Not Complete P1001 KOER Test Cannot Be Completed P1039 Vehicle Speed Signal Missing or Improper P1051 Brake Switch Signal Missing or Improper P1100 Mass Air Flow Sensor Intermittent

What causes a cylinder in a Ford Ranger to go dead?

Every cylinder, needs to have air, fuel, and spark to work. If any one of these components is missing from the equation, that cylinder will go dead. This means that so many different things can cause a misfire condition (or a rough idle condition). The cause of the misfire can be in any one of the following Systems:

Why does my Ford Ranger not turn on?

No lights on the dashboard when you turn the key is another dead giveaway that the battery is dead. In the instance where you have the engine swinging strongly at first, but slowly gets weaker and weaker with every swing until it just clicks, means any of the following components could be bad.

What are the trim levels of a 1993 Ford Ranger?

STX 4×2 Regular Cab 108 in. WB STX 4×2 Regular Cab 114 in. WB STX 4×2 Super Cab 125 in. WB STX 4×4 Regular Cab 108 in. WB STX 4×4 Regular Cab 114 in. WB

Why does my Ford Ranger not start up?

The fact that it runs as long as you spray the Quick-Start shows the engine is not getting fuel. Either the computer is not firing the injectors or something is keeping the pressure in the rail way too low. I would go back to the low or no fuel pressure as the first thing to check.

When did the Ford Ranger get a 4.0L engine?

Ranger Buyers Guide. The 4.0L OHV (Over Head Valve) V-6 engine found its way in to the Ford Ranger in 1990 and ultimately replaced the 2.9L V-6.

https://www.youtube.com/watch?v=RVbDHOiuKpQ

How to read service code on Ford OBD?

If using 12Vdc circuit test light, pay careful attention to length of pauses in order to read codes correctly. If using MIL/CHECK ENGINE light, service codes are displayed as flashes. Connections are displayed in image. A 1/2-second pause occurs between number of flashes in a digit. A 2-second pause occurs between digits in a code.

What are the codes for Ford check engine light codes?

81 Secondary -Air Injection Diverter (AIRD) solenoid circuit failure. 82 Secondary Air Injection Bypass (AIRS) solenoid circuit failure. 84 EGR Vacuum Regulator (EVR) circuit failure.

Where are Ford code 11 and 12 located?

Record all codes received. Turn ignition “OFF”. Ford DTC’s (Diagnostic Trouble Codes) Data Link Connector (DLC)(Located Under hood) Analog Voltmeter Connection Ford Codes 11 System PASS. 12 Cannot control rpm during KOER Sell-Test high rpm check.

What is the diagnostic code for Ford check engine light?

Refer to our Generic OBD II code list for definitions on all other Ford diagnostic trouble codes. P1000 OBD System Readiness Test Not Complete P1001 KOER Test Cannot Be Completed

What does Ford OBD I diagnostic code mean?

Ford OBD I Diagnostic Codes Trouble Codes› Ford OBD Trouble Codes Full list of OBD I Diagnostic Trouble Codes for your Ford Vehicle. If your Check engine lightis on you may have a serious problem. Scan your codes and follow the chart to determine what the code means. Some shops will scan your codes for free.

How to test Acura check engine light codes?

Next, read our article Automotive Circuit Testing 101, and if there is an article related to the system you are testing, such as Oxygen Sensors or EGR concerns, read these as well. They will provide valuable info! If there is a link to a specific diagnosis strategy for the code then follow that and start testing.

Where can I get free check engine light codes?

Scan your codes and follow the chart to determine what the code means. Some shops will scan your codes for free. Autozone is one place that will give you the code number. Or do it yourself with the procedure posted below.

What was the problem with the 91 Ford Ranger?

EGR Valve Position/EGR Pressure Feedback EGR Circuit Above Maximum Voltage (Others) — Check for clogged converter DC Motor Idle Speed Control/Idle Tracking Throttle Position Sensor Open Circuit (2.3L CFI & 2.5L HSC) Coil 2 Primary Circuit Failure (1990–91 1.9L MFI/SFI) Loss Of Ignition Diagnostic Monitor LH Side (2.3L)

Where does the fuel injection code go on a Ranger?

SERIES FUEL/AIR INJECTION CODES ON VEHICLES WITH DUAL OXYGEN SENSORS REFER TO THE LEFT OR FRONT SENSOR. EXCEPT: 1984-1988 3.8L ENGINE S: RIGHT SENSOR

What’s the BDTC code on a Ford Ranger?

Measured Air Flow High At Base Idle (1986–90 1.9L EFI) Spark Output (SPOUT) Signal Default To 10°. BDTC (3.0L SHO & 3.8L SC) Engine Coolant Temperature Circuit Open — This code is usually because the test was run with a cold engine, and the computer is expecting to see the sensor reading an already warmed engine.

What’s the misfire code for a leaking cylinder?

One or two cylinders have low or no compression. Worn cylinder head valves. Worn piston rings. Blown head gasket. Leaking intake gaskets will not set a specific misfire code, if OBD II equipped, but will set a P0300 Random misfire code and a P0174 Lean condition trouble code.

What kind of problem does a Ford Ranger have?

Thanks! Having same problem with 98 mazda b4000 v6, have had it towed to dealer twice and after bringing it off flatbed truck it starts right up. having the same problem 4Dec06. My 99, 4.0 ranger has a hard time starting when its cold out and it has sit over night.

What does no load test on Ford Ranger mean?

Its a no load test. Meaning if you are having problems with bad bearings in your starter it wont show up there. I would pull the starter again, and hold the gear in the nose, and shake it. If you hear a clunking sound, its not a good sound.

Is there a problem with my Ford Ranger?

I have a ranger with the 2.3L 8 plug, I have seen that many people with the same engine is having a stalling problem and so am I. I have change all the sensors except the pcm or the computer. Been having some problems with rough idle and stalling while sitting still.

Why is my Ranger not shifting into 1st?

After time, the slave cylinder fails to release the clutch completely. If you are having trouble shifting into 1st and reverse while stationary or if your truck creeps forward with the clutch pedal depressed the slave cylinder/throwout bearing is probably at fault.

How long does it take to clean a Ford Ranger?

It takes about 10 minuets total time and it’s worth the effort. On the can of cleaner they claim 4-10 more horsepower at the wheels with a clean MAFsensor compared to a dirty one. Expect a smoother cleaner running engine also. 4-10 more horses also translates into fuel savings.

Is there more horsepower in a Ford Ranger?

On the can of cleaner they claim 4-10 more horsepower at the wheels with a clean MAFsensor compared to a dirty one. Expect a smoother cleaner running engine also. 4-10 more horses also translates into fuel savings. This is a little job worth doing on any fuel injected vehicle not just the Rangers.

How do you get the Flash code on a 1994 Ford?

Connect the self-test outlet and input with jumper wire. Return to the driver’s seat and turn the key in the ignition. Do not start the engine, but get the electrical system running. Count how many times the check engine light flashes at you. There is a pattern to the flashes you will need to know in order to interpret the code.

Where to find EEC code on Ford 3?

(M) System shows voltage at pin 10 (is A/C on ?) or pin 30 (PNP, CPP switch) – PNP Service any EEC codes, erase memory and retest. If code is still present refer to instrument cluster diagnosis manual.

What does base readout on Ford 87-90 mean?

On 87–90 models, a base readout of 4255 indicates that KOEO self test has been entered. On 87–90 models, a base readout of 4030 indicates engine running self test has been entered. On 87–90 models, DTC output will be the RH three digits displayed.

Why does my Ford 4.0L explorer not start?

So, when your Ford 4.0L Explorer (Aerostar, Ranger or Mountaineer) Cranks but Does Not Start, it’s because one of these components is missing from the mix.

How to read FORD OBD diagnostic trouble codes?

No Heated Oxygen Sensor (HO2S) switching detected (front – HO2S) If using 12Vdc circuit test light, pay careful attention to length of pauses in order to read codes correctly. If using MIL/CHECK ENGINE light, service codes are displayed as flashes. Connections are displayed in image.

How do I read Trouble Codes on a 1993 Ford Ranger?