How big should the pinion nut be on a Dodge Ram?
How big should the pinion nut be on a Dodge Ram?
I did the same on my jeep with a d44 rear axle (also uses a crush sleeve), and torqued it back to about 150 ft lbs using the parking brake to hold the axles shafts from spinning. If I were you I would invest in a torque wrench to be sure it is right.
What should the torque be on a pinion nut?
Pinion nut torque should be above 200 ft/lbs with the stated torsional load from above. Good luck. Here is a pic i took from the piece of service manual i had when i did mine. with the torque specs.
Why is my pinion nut not tight enough?
Therefore, the amount of torque needed to set the new crush sleeve which sets the preload for the new bearings was EXTREMELY HIGH (we needed breaker bars and cheater pipes to get the slack out of the new bearings). We were way over the specs on the torque for the NEW crush sleeve.
What are the torque specs for a Dodge Ram?
Dodge Ram Pickup Torque Specs. Over 6,000 Automotive Torque Specs. Search Car Torque Specifications by Engine or Model Torque Spec Database Click on One of the Links Below Model Torque Specifications Torque Specifications for Dodge Ram Pickup Anti Roll/Stabilizer Bar To Axle Assembly
I did the same on my jeep with a d44 rear axle (also uses a crush sleeve), and torqued it back to about 150 ft lbs using the parking brake to hold the axles shafts from spinning. If I were you I would invest in a torque wrench to be sure it is right.
Pinion nut torque should be above 200 ft/lbs with the stated torsional load from above. Good luck. Here is a pic i took from the piece of service manual i had when i did mine. with the torque specs.
What’s the torque spec for a Dodge Ram?
The torque spec if I remember right is 25 used and 30 inch pounds new install. This is with the axles pulled. If the axles are still installed then add a little for them. I use a bicycle 0-60 inch pound beam wrench to measure the torsional load. But the key is no slop and a light torsional load that can be felt by hand.
Therefore, the amount of torque needed to set the new crush sleeve which sets the preload for the new bearings was EXTREMELY HIGH (we needed breaker bars and cheater pipes to get the slack out of the new bearings). We were way over the specs on the torque for the NEW crush sleeve.
When to replace the pinion seal on a Dodge Ram?
Discussion in ‘ General Discussions ‘ started by nigthrunner, Apr 9, 2014 . I was replacing broken spider gears and decided to replace the pinion seal while I was down there.
What’s the normal temperature of a motor bearing?
Normal motor bearing operating temperatures range from 140° to 160°F. As in all bearing applications, this measurement should be taken at the bearing outer ring. If the outer ring is inaccessible, take the measurement at the housing and add 15° to 20°F to estimate the correct bearing temperature.
How much torque do you need for pinion gear?
Then loctite the pinion nut and tighten to 15 inch-pounds rotating torque with used bearings or 25 inch-pounds with new bearings. 6.With the pinion gear installed, position ring gear and carrier into housing to check backlash.
Normal motor bearing operating temperatures range from 140° to 160°F. As in all bearing applications, this measurement should be taken at the bearing outer ring. If the outer ring is inaccessible, take the measurement at the housing and add 15° to 20°F to estimate the correct bearing temperature.
How much does it cost to replace wheel bearings on Dodge Ram?
Dodge Ram 2500 Wheel Bearings Replacement at your home or office. Dodge Ram 2500 Wheel Bearings Replacement costs $183 on average. Following is a breakdown of the labor and parts estimates. What are wheel bearings and how do they work?
What are the symptoms of bad wheel bearings?
The symptoms of bad wheel bearings include: Noise: A humming, rumbling or growling noise that increases with acceleration or as the vehicle turns. A loud constant whining or grinding noise when the vehicle is in motion. Clunking noises when driving over uneven road surfaces.
What is the spec on a pinion nut?
If you are talking about the pinion nut it is not hand tighten. The spec measures the torque required to turn the pinion gear by itself once the nut is tightened. The spec is NOT the torque applied to tighten the nut. That is whatever it takes to achieve the pinon bearing pre-load which is determined as described above.
