How do you replace the brake on a Dodge Ram?
How do you replace the brake on a Dodge Ram?
Rear brake assembly. 1. Disengage the secondary shoe return spring from the anchor pin. Figure 5. Secondary spring. 2. Disengage the primary shoe return spring from the anchor pin. Figure 6. Primary spring. 3. Push in on the hold-down retainer and turn it 90 degrees and remove the retainer, spring, and pin.
How to remove a brake drum that is stuck on?
Watch how to remove a brake drum that is stuck on. I go through the steps so anyone can remove their drum brake. In this case the drum adjuster was stuck so first try to get it off by wiggling back and forth. Then spray penetrating oil to remove rust between the drum and the seat. Then hit it with a hammer hard.
Why are my brake shoes not moving on my Dodge Ram?
If for some reason after tapping it with a mallet it still refuses to move, it is possible that the brake shoes might have dug into the brake drum. To free them up, you might need to loosen the adjuster that is located on the back inside the brake drum and can be accessed by an opening in the backing plate.
How do you remove rear wheel lug nuts?
Figure 2. Remove rear wheel lug nuts. The rear brake drum should be able to be slid off but might require a few taps with a mallet to free it up. If for some reason after tapping it with a mallet it still refuses to move, it is possible that the brake shoes might have dug into the brake drum.
Rear brake assembly. 1. Disengage the secondary shoe return spring from the anchor pin. Figure 5. Secondary spring. 2. Disengage the primary shoe return spring from the anchor pin. Figure 6. Primary spring. 3. Push in on the hold-down retainer and turn it 90 degrees and remove the retainer, spring, and pin.
If for some reason after tapping it with a mallet it still refuses to move, it is possible that the brake shoes might have dug into the brake drum. To free them up, you might need to loosen the adjuster that is located on the back inside the brake drum and can be accessed by an opening in the backing plate.
Do you need emergency brake serviced on Dodge Ram?
Have your emergency brake serviced, just like the rest of your brakes, to make sure it’s working correctly when called upon to do its job. This article applies to the Dodge Ram (1994-2001).
Figure 2. Remove rear wheel lug nuts. The rear brake drum should be able to be slid off but might require a few taps with a mallet to free it up. If for some reason after tapping it with a mallet it still refuses to move, it is possible that the brake shoes might have dug into the brake drum.
What is the purpose of the emergency brake on a Dodge Ram?
The emergency brake has two major functions. As the name suggests, it is a back up brake just in case your other brakes fail for some reason. It is also used as a parking brake to keep your vehicle rolling away while you’re not in it.
How do you jack up a Dodge Ram?
(Related Article: How to Jack Up Your Dodge Ram – Dodgeforum.com) Figure 1. Elevate rear wheels off ground. Using a breaker bar or an air impact wrench and the proper size socket, remove the wheel lug nuts that secure the rear wheel in place. Once you have removed the lug nuts, remove the rear wheel and place it out of the way. Figure 2.
How do you install a drum brake assembly?
put guide on anchor. place SA arm with pivot on rear shoe with nail, tube washer & straight spring Add actuator link, follow with overide spring from arm to pivot (next pic) Place return spring under SA arm. note placement of pivot and link Press shoes against anchor. Install front shoe return spring to anchor.
What is the assembly sequence for a GM drum brake?
Drum brake assembly Assembly sequence for a “typical” GM drum brake 1966 GM half-ton pickup (Delco Shown, Bendix similar) The parts pile, excl. park lever and pushrods. NOTE: colors are random paints I had on hand. Not “color-coded”. Self adjuster (SA arm) group Adjuster wheel group Where it all goes Park brake lever on the cable
What’s the best way to replace a drum brake?
Remove the spring and immediately hook it onto the new shoes exactly as you removed it. Inspect the brake wheel cylinder for any signs of leakage and replace if needed. Rebuild the new brake. The brake backing plates should be cleaned and lubed with a small amount of anti-seize on the slide points and anchor points.
Is there a self adjusting drum brake system?
Some drum brake systems don’t have a self-adjusting mechanism. Manually adjusted systems usually have a square adjuster at the back of the assembly. Winding this out as far as possible may help to get a badly worn or scored drum over the brake shoes.
How do you remove the drum from a car?
Grab the brake drum by the edges and pull it off. It may help to wiggle it a bit as you pull. It may be necessary to back off the brake adjuster to remove the drum. This is done through the brake adjustment hole in the drum or on the backing plate using a brake adjuster tool to turn the adjuster to loosen the brakes enough to remove the drum.
How do you replace the parking brake on a car?
Detach the parking brake lever. Hold the shoe retaining pin from the back and remove the retainer springs. Spread the shoes apart from the top and disengage the shoes from the wheel cylinder pins. Remove both shoes and the self-adjuster as one unit. Lay the old shoes on the ground next to the new ones.
