How do you fix a blower motor on a Dodge Dakota?
How do you fix a blower motor on a Dodge Dakota?
It requires two actions to release it from the blower motor resistor. On the Dodge Dakota I worked on, I found a red lock tab that required removal. Then you depress a black locking tang and hold it in while you wiggle the connector free.
Where is the blower motor on a Honda Accord?
The blower motor is located on the front passenger side below the glove compartment. You need to remove the glove compartment from the vehicle for easier access. Once removed, you will see the blower right in front of you. There should only be 3 screws holding it in place. From there, just remove it and number and wires you disconnect.
How to replace blower motor, harness, and resistor?
Replacing the Blower Motor, Burned-out Harness, and Resistor: 2001 Dodge Dakota. DIY. How To. – YouTube If playback doesn’t begin shortly, try restarting your device.
What does the blower motor switch do on a Dodge Ram?
The blower motor switch controls the speed at which the blower motor spins, and thus pushing air into the cabin of your Dodge Ram. At times, this switch can undergo an electrical malfunction or break down from normal wear. It also has brass contacts that can stop relaying signals due to the accumulation of dirt and grime.
It requires two actions to release it from the blower motor resistor. On the Dodge Dakota I worked on, I found a red lock tab that required removal. Then you depress a black locking tang and hold it in while you wiggle the connector free.
Are there any problems with the Dodge blower motor?
And after doing a little research I discovered that a lot of other people are going through the same thing. Here we’ll discuss the common issue of Dodge blower motor problems and the recommended steps to help prevent melted connectors, damaged wire harnesses and repeat failures of the blower resistor.
Replacing the Blower Motor, Burned-out Harness, and Resistor: 2001 Dodge Dakota. DIY. How To. – YouTube If playback doesn’t begin shortly, try restarting your device.
Do you need to splice a Dodge blower motor?
You need one to help remove the metal connector from the plastic holder. Another issue, all the wires in the kit are the same color. For this reason it’s recommended to perform splice repairs one at a time. This way they end up in the same place as the factory connector.
And after doing a little research I discovered that a lot of other people are going through the same thing. Here we’ll discuss the common issue of Dodge blower motor problems and the recommended steps to help prevent melted connectors, damaged wire harnesses and repeat failures of the blower resistor.
Why is my Dakota heater / AC fan not working?
I don’t believe the issue to be the blower motor itself, because it has been running flawlessly and very quietly…no rattling, squeaking or anything that would lead me to believe the motor has failed. My truck is a 1997 Dakota 3.9L automatic….with 186,000 miles on it.
Is there a problem with my Dodge Dakota?
My neighbors 01 Dodge Dakota pickup truck was having an HVAC blower motor issue. It worked on high only and sometimes not at all. When I typed a description of the problem in my favorite search engine, the number one result said.
Why is my Dodge Dakota air not working?
2004 dodge Dakota air or heat not blowing?My air just stopped blowing it truck. It will not blow when I switch it to heat either. I noticed I was low on coolant so I added some, it started working just fine and worked for about an hour then stopped again.
What to do if your Dakota heater is not working?
Thanks for the good information, I have a 2004 Dakota with your problem ( only the high speed worked ) Took to the dealer and asked them to replace the resistor and harness, works great now! Bye the way, parts and labor were total 160 bucks, not bad ! Did you find the recommended reading relevant to this discussion?
Where is the blower resistor on my 96?
Works great now. Anita, on my 96, the blower resistor is accessible from under the hood, right on the firewall, just ahead of the passenger side, about 6 inches below the windshield. You’ll notice a connector with about 6 wires going in one connector.
Are there any problems with the Dodge Durango blower?
Note that Chrysler evaporator core problems continue to grow and that AC part is close to the fan motor. Although it was the Dakota that tipped me off to this problem, I can see the Dodge Durango from 2001 through 2006 uses the same part number and wiring harness repair kit.
Why is the motor on my Dodge blower not working?
However, lets still call it a bit of a struggle, because the plastic from the connector had melted and fused to the plastic of the resistor bridge. In addition, when you attempt to pull the wires in an out of the plastic connector you’ll find them retained with a locking mechanism.
Do you have a 2001 Dodge Dakota AC blower motor?
Do you have a 2001-2004 Dodge Dakota, or 2001-2006 Dodge Durango AC blower motor fan speed locked in one position? I said to myself, yes I do. And after doing a little research I discovered that a lot of other people are going through the same thing.
I don’t believe the issue to be the blower motor itself, because it has been running flawlessly and very quietly…no rattling, squeaking or anything that would lead me to believe the motor has failed. My truck is a 1997 Dakota 3.9L automatic….with 186,000 miles on it.
Note that Chrysler evaporator core problems continue to grow and that AC part is close to the fan motor. Although it was the Dakota that tipped me off to this problem, I can see the Dodge Durango from 2001 through 2006 uses the same part number and wiring harness repair kit.
My neighbors 01 Dodge Dakota pickup truck was having an HVAC blower motor issue. It worked on high only and sometimes not at all. When I typed a description of the problem in my favorite search engine, the number one result said.
Why does my Dodge blower motor keep overheating?
However, it wasn’t the configuration of the circuit that’s causing the blower motor resistor to overheat. The overheating gets so intense that in many instances you’ll find the connector damaged. When people just replace the resistor they might find the automobile still has intermittent blower operation.
Why does my AC blower motor work intermittently?
Intermittent electrical problems can make you feel like your a blind man trying to catch a stray dog. You can’t post conmments that contain an email address.
What does it mean if your blower motor is not working?
Average rating from 849 customers who received a AC is not working Inspection. The blower motor resistor is an electrical component that is a part of the vehicle’s heating and air conditioning system. It is responsible for controlling the blower motor’s fan speed.
Why does my Dodge Dakota blower keep going bad?
If you leave the blower motor switched continually on you may not notice this. If so I suspect that there is an earth fault on one of the wires connected to either pin 4 or 5 of the resistor. Here is a the blower circuit for a 2002 Dodge Dakota. Hopefully it is the same for your particular year model.
What was the problem with my blower motor in 2003?
A shop mechanic said it was the blower motor drawing too many amps and it was bad, so I replaced the motor and connector. After replacing the connector again I tried the old resister just to see if it was really dead. It worked fine. Week later the connector melted again ( this is with a new motor).
Why does my Dakota blower resistor keep going bad?
When your Dakota or Durango left the factory, it had a Mopar motor and voltage resister that were compatible with each other. After 10-15 years the motor wears out , begins to draws more amps burns up the resister. Most people replace the wiring harness and the resister with. cheap replacement from Autozone / Advanced etc.
What kind of motor resistor do I need for a Dodge blower?
This includes the Dorman 973-026 Blower Motor Resistor for Chrysler or Dodge automobiles and TYC 700071 Replacement Front Blower Assembly for around eighty dollars. This is a selected page from the air-conditioning section of the you fix cars website.
This includes the Dorman 973-026 Blower Motor Resistor for Chrysler or Dodge automobiles and TYC 700071 Replacement Front Blower Assembly for around eighty dollars. This is a selected page from the air-conditioning section of the you fix cars website.
What are the symptoms of a bad heater motor resistor?
Symptoms of a Bad or Failing Heater Blower Motor Resistor. 1 1. Blower motor stuck on one speed. A common symptom of a faulty blower motor resistor is a blower motor that is stuck on one setting. The blower 2 2. Blower motor does not work on certain settings. 3 3. No air from the vehicle’s vents.
However, it wasn’t the configuration of the circuit that’s causing the blower motor resistor to overheat. The overheating gets so intense that in many instances you’ll find the connector damaged. When people just replace the resistor they might find the automobile still has intermittent blower operation.
Why is the fuse on my blower not blowing?
The fuse protecting the blower motor circuit is a 40 amp fuse (it may also have other components on that circuit), so that may explain why the fuse is not blowing. All the information I have found agrees with what you have done already – if the resistor continues to overheat, replace the motor.
The fuse protecting the blower motor circuit is a 40 amp fuse (it may also have other components on that circuit), so that may explain why the fuse is not blowing. All the information I have found agrees with what you have done already – if the resistor continues to overheat, replace the motor.
Why is my Dodge Ram blower resistor bad?
There are various failure modes in the blower motor resistor. Part of the resistor could fail or the entire resistor could completely fail. Also consider that your fan speed control could be faulty. There is also a chance that your blower motor is bad.
Where to replace the blower motor on a Dodge Dakota?
Try an auto parts store or rockauto.com. Replacing it is a challenge. The entire dash has to be rolled back and the heater plenum removed. You’ll have to discharge the a/c and drain the cooling system. Be sure it really is the motor before you tackle this and if you do, replace the heater core while you’re in there.
When your Dakota or Durango left the factory, it had a Mopar motor and voltage resister that were compatible with each other. After 10-15 years the motor wears out , begins to draws more amps burns up the resister. Most people replace the wiring harness and the resister with. cheap replacement from Autozone / Advanced etc.
How do you change the blower motor resistor?
If you want to change the blower motor resistor you just have to remove the two screws and the wiring harness that connect to it, but you have to loosen the dash enough to tilt it back by about 6 inches to gain access to the resistor.
The blower motor is located on the front passenger side below the glove compartment. You need to remove the glove compartment from the vehicle for easier access. Once removed, you will see the blower right in front of you. There should only be 3 screws holding it in place. From there, just remove it and number and wires you disconnect.
However, lets still call it a bit of a struggle, because the plastic from the connector had melted and fused to the plastic of the resistor bridge. In addition, when you attempt to pull the wires in an out of the plastic connector you’ll find them retained with a locking mechanism.
