How do you replace the power seat motor on a Dodge Ram?

Install the new power seat motor. Fold the seat forward, and place it back in the truck. Re-install the center console and seat bracket bolts. Put the seat belt receptacle back in place. Re-tighten the front two passenger’s seat bolts. Reconnect the two power connections under the seat, and test the seat to make sure it works properly.

What to do if your power seat fails?

Test the relay if your circuit has one between the switch and the failed motor. Operate the switch and make sure the relay is receiving voltage from the switch; also, test for outgoing voltage from the relay to the motor using a test light. Make sure the relay is properly grounded. Remove or move the seat to the side if possible for this test.

How do you remove a power seat switch?

Part 1 of 2: Removing the power seat switch. Step 1: Disconnect the negative battery cable. Disconnect the negative battery cable and set it aside. Step 2: Remove the seat trim panel. Remove the trim panel retaining screws using a screwdriver. Then pull the seat trim panel away from the seat cushion in order to release the retaining clips.

Is there a way to adjust the power seat?

Anything he/she likes. It could be adjusted through the use of a set of electric motors. Most of the automobiles of cars having this have controls designed for the driver’s seat only. With this seat, occupants or passengers can adjust their seat through its switch.

Is there a way to repair a power seat?

Repairing car power seat problems can sometimes be as simple as removing a penny from the seat track. Or they can be as complicated as having to test switches, relays and motors. Most power seats are not protected by a fuse but instead use a circuit breaker.

How do you take a motor out of a Dodge Ram?

Hammer the roll pin until it is flush with the housing, but do not remove it. Use a grinder or Dremel tool to grind 3/16″ out of the roll pin between the motor housing and the seat track (see Figure 3). Finish hammering out the roll pin and pull the motor out.

What to look for when troubleshooting a power seat?

The trick when diagnosing car power seats is to focus on the mechanical or electrical problem areas: the mechanism that fails to lower and raise the seat, or the part that slides or tilts the seat forward and backwards. Keep this in mind as you troubleshoot your power seat, whether it comes with one, two or three motors.

What are the fuses on a Dodge Ram 1500?

Ignition Switch (Run-Start A21, Start A41, Off-Run-Start A51 (Cluster, Powertrain Control Module, Integrated Power Module, Push Button Starter Switch)) Cluster, Compass/Mini Trip Computer (except Base), Automatic Day/Night Mirror (except Base), Door Lock Switch – Passenger (except Base)

What should the voltage be on a Dodge Ram?

Check to see if the MAP sensor is running the right voltage. The MAP sensor needs to read close to 2.0 volts when the motor is started cold. Anything below 1.9 v is a sign that the MAP sensor is reading the air-to-fuel ratio inaccurately and adhering to poor gas mileage.

How to troubleshoot Dodge Ram 1500 SLT power windows?

Operate the switch in both directions and simultaneously probe the connector for power. If there is power the motor is bad. If not, the wiring from the switch is bad. Remove the regulator and motor if the motor had worked previously but the window regulator did not work.

Why are my power windows on my Dodge Ram not working?

An electrical problem could be anywhere from the fuse to the automatic control box in the armrest. A mechanical problem could be either a motor or a regulator. To isolate the problem, check to see if all of the other windows work properly.

Is there a power seat in a Dodge Ram?

This article applies to the Dodge Ram 3rd Generation (2002-2008). Power seats are a nice addition to any vehicle, but just like any other power option, they have a lot of moving parts that can break. Unfortunately, a failing power seat motor is a fairly common issue in 3rd generation Dodge Rams.

Can you put a jumpseat on a Dodge Ram?

Step 5: Bolt down the seats. Most people opt not to add any bolts to the jumpseat as it holds on very well using the two bolts that are on there already from the passengers seat. Since the seatbelts are mounted to the Drivers and Passengers seat, and not the jumpseat, it’s not really a safety issue.

How much does it cost to replace a seat on a Dodge Ram?

You could easily spend $1000 on brand new covers, another $500 on replacement foam, and then another $1000 on installation. After all of that investment you just have to hope that the covers and foam you purchased both meet OEM Specifications, and that your installer actually knows what he’s doing while he holds your truck hostage for three days.

Is the driver seat a manual or power seat?

The driver seat is a power seat where I had manual before and I cant adjust it. On further inspection I found that on the yellow big connector from the floor to the seat im missing the red wiring coming to the connect which there is on the seat side. Im assuming thats 12v+ but not 100% sure.

Can a power seat be converted to a regular seat?

Because all the pins are in the same location, everything you have on your current seats (like airbags, occupancy sensor, and seatbelt sensors) will work on your new seats just by plugging them in. alschief likes this. (You must log in or sign up to reply here.)

Is there a way to manually move a power seat?

The adjustment motors of the power seat are bidirectional. The rotation directionof the motor is dependent on the particular direction that the switch is being set or pushed. That’s why when it’s not performing very well, you should check it before you left with the choice to manually move a power seat.

Why is my power seat not moving forward?

A seat may be jammed if it cannot freely move in the forward or backward direction, but can only move in one direction, or simply works inconsistently. Your first step is to find out if your seat’s other components are working, by confirming that the fuse, the relay switch, and the circuit breaker are in good condition.

How tall is the front seat on a Dodge Ram?

Don’t be stuck sitting in your ’03-’09 Dodge Ram 2500/3500 and ’02-’05 1500 with the front seat at only one height. Get this replacement seat motor. X Sign up to keep in touch

Why is the seat control not working on my Dodge Ram?

The ring & pinion gears are plastic, and they strip easily. Mine has 4 teeth ripped off. The motor will hum or buzz when the switch is operated, but the seat track doesn’t budge. It may be good reason not to hold down the switch till the seat track bumps either the up or down stop.

What to do when your power seat is not working?

When the motor of your seat is not working, this is one right thing to do. This is one of the easiest ways when you found out that your seat motor is not fully working. You can do this to manually move power seat. With this method, you will be able to adjust your power seat to whatever direction you’d love to.

How do you replace the power seat motor on a Dodge Ram?