Easy lifehacks

Is idling bad for semi trucks?

Is idling bad for semi trucks? Why Idling a Big Rig Isn't Recommended Idling a truck can be dangerous. Idling can shave life off the engine itself. Engines only run a fixed number of hours before they experience fatigue and start to breakdown. Why do truckers leave their trucks idling? Truckers, both independent owner-operators and fleet drivers, leave their engines idling for three main reasons: weather conditions, economic pressures, and old habits. In cold weather, a truck's engine and fuel tank need to stay warm. Do truckers leave their engines running when sleeping? The primary reason that truckers leaving their...
Common questions

Does Massey Ferguson 65 have live PTO?

Does Massey Ferguson 65 have live PTO? I am considering buying a 1964 Massey Ferguson 65: The PTO does not always engage when the engine is running. This is a "live" PTO with the dual clutch. How does the PTO on a tractor work? The tractor's stub shaft, often called the PTO, transfers power from the tractor to the PTO-driven machine or implement. The PTO and drive shaft rotate at 540 rpm (9 times/second) or 1,000 rpm (16.6 times/second) when operating at full recommended speed. How many HP is a Massey Ferguson 65? Massey Ferguson 65Massey Ferguson 65 PowerDrawbar (claimed):33...
Easy tips

What are the features of the bobcat 863?

What are the features of the bobcat 863? Bobcat 863 features Bobcat Interlock Control System (BICS) that makes sure that the loader can be controlled only if everything, including the operator, is ready. 2. Bob-Tach System Bobcat 863 features a convenient and secure attachment system. Where is the boss @ system located on a bobcat? The BOSS@ System uses a microprocessor, located behind the operator cab to: Monitor loader/engine functions Warn of system malfunctions Perform automatic shutdown under certain catastrophic conditions Store defect codes for later service access Control glow plug operation soss e What do you need to know...
Easy lifehacks

How to set valve lash clearances on a portable gas generator?

How to set valve lash clearances on a portable gas generator? This video will show you how to set the Valve Lash Clearance settings on a Portable Gas Generator. With step by step instructions on how to prepare, set the engine and measure the clearances. If you need Valve clearance settings please look up the Valves for your generator on our website. What does a lash do on a pushrod engine? Valve lash is the mechanical clearance in the valvetrain from the valve tip to the rocker in a pushrod engine using solid lifters. How do you adjust a 235...
Other

Is there a 1993 Ford F700 dump truck?

Is there a 1993 Ford F700 dump truck? 1993 Ford F700 Diesel Single Axle Dump Truck Under CDL. This is a great running smaller dump truck with lots of power. Features: F700 Diesel with 6BT... 1987 Ford dump truck. Runs extremely well with 8.2 Detroit diesel. fluids and filters recently changed ($300.00). New lights installed where needed. Are there any Ford F750 dump trucks for sale? The New York-based material-handling company’s drivers “absolutely love the T880s.” Freightliner says the option to spec its versatile vocational truck with the X12 will be a big advantage for weight-sensitive configurations such as concrete...
Common questions

What happens if you over torque rod bearings?

What happens if you over torque rod bearings? Torque. Over-torqued or over-tightened bearings cause the rod end cap to bow in the center, resulting in an out-of-round profile. The center gap in the bearing will chafe and vibrate with each revolution, degrading the bearing material and removing minute metal particles. Is the connecting rod bearing torque to yield? Haynes states that the connecting rod bolts are torque to yield for the main bearing bolts; however, it is not clear if the connecting rod bolts are torque to yield also. Does anyone know if the connecting rod bolts are reusable or...
Easy tips

What causes a backhoe to not go into gear?

What causes a backhoe to not go into gear? A: This is caused by excessive clearances in clutch packs due to worn plates & can only be repaired by overhauling. Q: My transmission will not go into gear? A: The powershift transmission is controlled by electrics/hydraulics/mechanical drive. – are lights flashing on LED readout? Take note of what they are – they are codes to assist diagnosis How to ensure the throttle returns to closed properly on a car? With or without the engine running, If you twist the gas wide open & let off by just relaxing your hand...
Easy tips

Is there a command to list all mounts in Linux?

Is there a command to list all mounts in Linux? There is no such command, since there is no list of "attempted mounts". You can compare the current mount list ( /etc/mtab) to the list of shares registered to be mounted though ( /etc/fstab ). Alternatively you could try to grep through the system log files to find failed mount attempts. How can I find out if a share has been mounted? You can compare the current mount list ( /etc/mtab) to the list of shares registered to be mounted though ( /etc/fstab ). Alternatively you could try to grep...
Most popular

How to call Altec parts for parts support?

How to call Altec parts for parts support? Customers will never be sent to voicemail when calling 877-GO ALTEC for parts support. Altec Parts is the only authorized dealer of genuine Altec new and replacement parts. We also provide emergency and storm coverage to ensure you get your parts order accurately and with urgency. What kind of power rating does Altec Lansing have? 1. RMS continuous power— both channels driven 8 ohms The RMS continuous power rating is used exclusively in the professional audio field, testing laboratories and high fidelity magazines for test reports. For this reason we have chosen...
Easy lifehacks

How does the ICP sensor work in a Caterpillar engine?

How does the ICP sensor work in a Caterpillar engine? The ICP sensor reads the pressure from the engine's high pressure oil system. The Ford Power race, Navistar Internatonal and the Caterpillar engine use this type of sensors. The engine ECM uses this information to order the correct signal to the fuel injectors that will measure the delivery of fuel to the engine. Can a bad MAP sensor cause engine failure? MAP sensor on footwell inside engine compartment. A bad manifold absolute pressure (MAP) sensor can upset fuel delivery and ignition timing. Depending on your vehicle model, your engine might...