Most popular

How to replace the gear shift indicator on a Ford F-150?

How to replace the gear shift indicator on a Ford F-150? THANK YOU FOR THE HOW TO POST. fred : Replace gear shift indicator adjustment knob. I have 2003 ford f-150 STX, the indicator on column went all the way over to the right. Pull off bottom panel 5 screws and laid it down on floor board becuase the brake and hood release i left attached. How to fix shift cable on Ford F-150? This shift cable bushing repair kit allows you to fix your Ford F-150 shift cable bushing very easily. It takes about 2 minutes and comes with...
Easy lifehacks

How do I reprogRam my keyless entry key fob?

How do I reprogRam my keyless entry key fob? How to Program a Key Fob in 5 Simple Steps (Car Key Guide)STEP 1-Turn on the ignition. You should sit in the driver's seat with both the ignition key and the key fob with all doors closed. STEP 2-Press the lock button. STEP 3-Turn off the ignition. STEP 4-Repeat the process with other key fobs. STEP 5-Restart the process. How to program a Ford Explorer keyless entry remote? Note: If your vehicle cannot enter programming mode, then you cannot program any remote. This indicates either no keyless entry installed on the...
Easy tips

What should I do if my ho2s sensor is not working?

What should I do if my ho2s sensor is not working? Check the manufacturer’s specifications, as there may be a chart informing you of what the voltage should be at a given RPM. If it fails this test, replace the MAF sensor and retest. If all tests have passed so far, and you continue to get a P1131 code, monitor the HO2S. Where to find the ho2s switch on a Ford? Typically, it will be found close to, if not directly screwed into the exhaust manifold that cylinder 1 exhaust gases flow out of. Once located, visually inspect the connectors...
Other

What to do if you have problems with your VCT solenoid?

What to do if you have problems with your VCT solenoid? At the first sign of trouble with a VCT solenoid, you should drive right down to your certified mechanic and have them take a closer look at it. They can tell you if your VCT solenoid is the part that’s giving your cars problems and replace it, if necessary. What do you call a non-contact voltage tester? Volt Stick (sometimes also referred to as a volt pen, voltage indicator or wand) is a non-contact tester pen which provides simple, accurate testing for the presence of voltage, without the complications...
Easy lifehacks

Do you have to remove coil pack when changing spark plugs?

Do you have to remove coil pack when changing spark plugs? If you’ve ever changed sparkplugs before this will be familiar to you, with the exception that you have to remove the coil pack to get to them, which is just one small bolt. Be sure to vacuum or use compressed air down in the sparkplug well before removing the spark plug. These engines don’t like small rocks in the combustion chambers. How long does it take to change spark plugs on old truck? If you have been at these kinds of projects for a while you may recall changing...
Easy lifehacks

Why did I get service AdvanceTrac on my F150?

Why did I get service AdvanceTrac on my F150? But other f150 forums say that either the throttle body is the culprit or the steering rack. So probably not under powertrain warranty. Last time I had Service AdvanceTrac message and light on in my 07’ it was an ABS sensor/ harness. When does the service AdvanceTrac warning light come on? Service AdvanceTrac Warning advance trac® power steering Whenever the "Service AdvanceTrac" warning light comes on the turn signals don't work properly. You have to hold them either up or down in order for them to continue flashing. When the warning...
Common questions

What does the ICP sensor stand for?

What does the ICP sensor stand for? Injection control pressure sensor The ICP sensor or Injection control pressure sensor is found on Ford's Powerstroke 7.3 L diesel engines. The ICP sensor is responsible for monitoring oil pressure being passed on to the PCM to pressurized fuel injectors using the IPR (Injection Pressure Regulator) for proper vehicle operation. What does IPR stand for on a diesel engine? Page 1. Injection Pressure Regulator (IPR) General Information: A Powerstroke engine utilizes an electromagnetic valve to regulate the high pressure oil pressure on the engine to tailor the injection characteristics of the injectors. This...
Common questions

What engine came in a 1966 Mustang?

What engine came in a 1966 Mustang? 1964½–1966Mustang 1964½–1966PowertrainEngine170 cu in (2.8 L) Thriftpower I6 200 cu in (3.3 L) Thriftpower I6 260 cu in (4.3 L) Windsor V8 289 cu in (4.7 L) Windsor V8 289 cu in (4.7 L) Windsor HiPo V8Transmission3-speed manual 4-speed manual 3-speed automaticDimensions What engine did the original Mustang have? The first model Mustang, the Early 1965 Mustang (or as many refer to it, the 64 ½), was available as a coupe or convertible and featured a base 170-cubic inch six-cylinder engine with a three-speed floor shift transmission. Was the original Mustang a V6?...
Most popular

What are the torque specs on a Ford truck?

What are the torque specs on a Ford truck? 6.9 & 7.3 IDI Intake & IP Gearhouse Torque Specs and Sequencing. Miscellaneous torques: (Taken from the Official Ford “1988-1993 Engine Service Manual, Supplement 7.3 Liter Diesel Engine” and the Official Ford “1988 Truck Shop Manual, Vol. How much torque does a 2000 Ford F250 have? Ford Super Duty Torque Specifications 2000 Ford F250 Torque Specifications These are torque values for a 2000 Ford truck. Most will be applicable to model years 1999-2003. Description Torque Specification Socket Size A/C compressor support bracket mounting bolts 30-41 lb/ft, 40-55 Nm A/C compressor support...
Easy tips

How many sensors are needed for inspection?

How many sensors are needed for inspection? How Many Monitors Have to be Ready? The US Environmental Protection Agency (EPA) guidelines allow up to two monitors to be in a "not ready" state for model year 1996 through 2000 vehicles and one monitor "not ready" for 2001 or newer model year vehicles. How to pass an emissions test in New Jersey? Here are some tips to keep in mind to ensure passing a New Jersey vehicle emissions test: Make sure the vehicle does not have its “Check Engine” light on; If it does, it will not pass the test. To...