Other

Where can I find a 1998 throttle control guide?

Where can I find a 1998 throttle control guide? 1998 GUIDE TO ELECTRONIC & MANUAL THROTTLE CONTROLS ETC98: 1 1998 GUIDE TO ELECTRONIC & MANUAL THROTTLE CONTROLS IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 TEL: 641-923-3711 MANUAL PART NUMBER 99901267 99901267: 20070329 Iowa Mold Tooling Co., Inc. is an Oshkosh Truck Corporation company. What happens when the throttle controller goes bad? In any case, in some instances it will cause the throttle controller to lose a signal and deliver intermittent throttle control. Sometimes this is a minor issue that is more of an inconvenience while other times...
Most popular

Where can I find the Embraco compressor Handbook?

Where can I find the Embraco compressor Handbook? The information of this Handbook is limited to the Embraco european on-off compressors and to their installation/operation/service. What's the best way to use an air compressor? 1. Keep work area well lit. 2. Operate compressor in a well-ventilated area free from flammable liquids and vapors. 3. Operate compressor in a ventilated area so that compressor may be properly cooled and the surrounding air temperature will not be more than 100°F. 4. Never use a compressor in a wet environment. 5. What should the pressure be on a 216v air compressor? (130 psi...
Common questions

What is the fault code for a Kubota excavator?

What is the fault code for a Kubota excavator? KUBOTA Excavator Fault Codes DTC KUBOTA Excavator Fault Codes DTC data000 This LCD display shows the following conditions;fuel amount, water temp., engine oil pressure, battery, glow plug, and operating hour meter. data001 This LCD display shows the following conditions;fuel amount, water temp., engine speed. What are the flashing codes for fuel rail pressure? Flashing codes are described. P0087 (flashing code 227) fuel rail pressure too low (for a pump without pressure applied) • Strong engine vibration. • There may be too much smoke. P0088 (flashing code 118) fuel rail pressure too...
Easy tips

Does a Cat 226B have high flow?

Does a Cat 226B have high flow? Two fixed displacement gear pumps provide flow and pressure for the 226B high flow loader and auxiliary circuit at 100 L/min at high idle. Maximum system pressure for the loader and auxiliary circuit is 23 000 kPa and 3334 psi. Are there hydraulic controls on a 226B skid steer? More buttons are used on high flow option machines but, that is not available on the 226B. Once you have the bottom covers removed from the joysticks, you will see the lines and to harnesses. Lift the boot under the lever and you will...
Easy tips

How much does a John Deere 50d mini excavator weight?

How much does a John Deere 50d mini excavator weight? 10428 lbs Operating SpecificationsFuel Capacity18.5 gal (70 l)Hydraulic Pump Flow Capacity33 gal/min (125 l/min)Hydraulic System Fluid Capacity21.7 gal (82 l)Operating Weight10428 lbs (4,730 kg) What does a John Deere 60g excavator weigh? 13,620 lb. 60GCompact Excavator. Max Digging Depth: 3.77 m (12 ft. 4 in.) Operating Weight: 6180 kg (13,620 lb.) How much does a John Deere 35G cost? $44,900. NEW John Deere 35G excavator. Zero tail swing design makes this compact extra maneuverable and plenty productive in places with tight spaces. Choose the tracks that are best for the...
Easy lifehacks

Why is my grapple bucket not working on my tr320?

Why is my grapple bucket not working on my tr320? It's specifically called out in the Hydraulic Enable Switch overview. So one more issue with the tr320.... It is up and moving again, so I hooked up my grapple bucket and attempted to operate it soon finding out the machine acts as though it has little pressure on the auxiliary connection. When do I get the error code oprpr on my tr320? Discussion in ' Compact Track/Multi Terrain Loaders ' started by shakori00, Sep 28, 2014 . I just finished power washing my 2011 TR320 compact track loader. I got...
Easy tips

How does a cat 440 backhoe loader work?

How does a cat 440 backhoe loader work? Both the 440 and 450 backhoe loaders are built with common single-tilt loader arms. Electrical sensors positioned at the tilt and lift arm enable parallel arm movement for increased material retention when lifting the loader bucket and safe handling of palletized loads. Why does my bucket not uncurl when I hit it? After that impact, the bucket no longer un-curls. It curls fine. It goes up and down fine, but if you try to uncurl, it moves about 1 inch and then stops. I tried reversing the hydraulic lines (curl hydraulic circuit...
Easy lifehacks

What is a failsafe way to time a Deere 4039d?

What is a failsafe way to time a Deere 4039d? I NEED TO DO THE WHOLE TIMING. THE CAM IS OUT AS WELL AS T..HE INJECTION PUMP.THE ENGINE WAS HUNTING WITH A LOT OF WHITE SMOKE. THANKS , SYTO Customerreply replied 12 years ago What is the Technical Manual for John Deere? This Component Technical Manual contains service information on the 3029, 4039, 4045, 6059 and 6068 engines produced by JOHN DEERE Saran (FRANCE) for the applications listed in the application chart. NOTE: Information on how to remove and reinstall the engine in the vehicle is contained in the relevant Technical...
Easy tips

What should I do about my Isuzu diesel engine?

What should I do about my Isuzu diesel engine? Protect your customer’s engine from contaminated fuel by recommending regular fuel system inspection and maintenance. This will ensure continued performance of the Isuzu Diesel engine and provide the earliest detection of diesel fuel contamination. Maintenance is the customer’s responsibility. How to diagnose and repair Isuzu truck with 4JJ1? If no there is no indication of DEF contamination follow Procedure B. 1.Remove cap from fuel tank. 2.Disconnect suction line from the water separator. 3.Use air to push fuel and contaminants into fuel tank. 4.Reconnect suction line to water separator. 5.Clean the fuel...
Easy tips

How big is a 19hp Briggs and Stratton mower engine?

How big is a 19hp Briggs and Stratton mower engine? Briggs & Stratton Professional Series™ 540cc 19 Gross HP OHV Electric Start Vertical Engine, 1" x 3-5/32" Crankshaft, 1/4" Straight Keyway *This product qualifies for Free Shipping anywhere in the contiguous US. Are there any regulations for sickle bar mowers? Due to the exposed cutting blade design, sickle bar mowers cannot meet the current safety regulations set by the American National Standards Institute (ANSI). Only manufacturers that had approved designs prior to the current regulations becoming effective may continue to manufacture these type of mowers. Is the Troy Bilt sickle...