Easy tips

How long does it take a locksmith to make a transponder key?

How long does it take a locksmith to make a transponder key? Creating a car key will take anywhere from 10 to 30 minutes, depending on the type of key and complexity of the transponder system. In rare cases where your locksmith does not have a blank key in stock, rest assured that they can order it for you and provide a spare set as soon as possible. Can you replace a transponder key on a Chrysler? If the Chrysler car key replacement is a transponder key, then it will have to be programmed and paired with your specific Chrysler...
Common questions

What is the advantage of a 3 cylinder engine?

What is the advantage of a 3 cylinder engine? A 3 cylinder engine is much more fuel efficient compared to a 4 cylinder engine of the same size. This is because of two primary factors, reduced frictional losses and lighter weight. Since there is one cylinder less, the frictional losses caused by metal surfaces coming in contact within the engine block is lesser. How much horsepower does a 3.0-liter engine have? The 3.0L LFW engine delivers a market-leading balance of specific output, high torque over a broad rpm band, fuel economy, low emissions and first-rate noise, vibration and harshness control....GM...
Easy lifehacks

How do you program a 2006 Dodge key?

How do you program a 2006 Dodge key? 2006 Dodge Ram 1500 Remote ProgrammingPress and hold UNLOCK button.After holding the UNLOCK button for a at least 4 seconds, continue holding the UNLOCK button and also press PANIC button within 6 seconds.Ensure acoustic signal is emitted indicating programming mode active.Release both buttons. How much does it cost to replace a 2006 Dodge Charger key? Hear this out loudPauseIn short, replacing a Dodge Charger key can cost between $50 to $350. How to program a keyless entry remote for a Dodge truck? Below are the programming instructions for the keyless entry remote...
Easy tips

Does a 12 valve Cummins need a computer to run?

Does a 12 valve Cummins need a computer to run? All 12-Valves are non-electronic injection pump engines and DO NOT require any electronics from the truck to run. Is the Cummins 12 valve engine unkillable? No diesel engine on earth is as legendary as a 12-valve Cummins. Not only is the inline-six known for its awesome stock torque figures, but the 1,100 pound iron hulk from Columbus, Indiana has a reputation for being almost literally unkillable, even after it’s been modified to produce prodigious power figures. Where did the Cummins 6 valve engine come from? He went on to say...
Most popular

Can shocks cause death wobble?

Can shocks cause death wobble? Death wobble is often blamed on a failed steering stabilizer or shocks and struts. Worn tie rods, idler arm, track bar, wheel bearings, pitman arm, steering center link and shaft, ball joints, alignment and even tire pressure can combine to cause the death wobble. Is there a locking hub on a Ford 4WD? Locking Hubs – Yes on No? In the beginning, Ford used manual locking hubs on their 4WD vehicles. This required you to get out and physically turn a knob on the front wheel hubs to lock the wheel and the axle shaft...
Other

Can a bad O2 sensor cause a car to stall?

Can a bad O2 sensor cause a car to stall? Bad performance. Your car may misfire or experience hesitation and stalling. Most cars default to the factory air-to-fuel ratio if the oxygen sensor fails, which can cause problems because of non-standard temperature, moisture, or air composition. How does an O2 sensor work in a catalytic converter? You can also check exhaust backpressure ahead of the converter by connecting a pressure gauge to the EGR exhaust port, an O2 sensor port, or an exhaust manifold air line connection. More than 1.25 psi of backpressure at idle, or more than 3 psi...
Common questions

How do you reprogram a Dodge key fob?

How do you reprogram a Dodge key fob? To reprogram your Dodge key fob, follow the four easy steps below. These steps will also work on select Chrysler, Jeep, and RAM models in Bartlett and Streamwood. Step inside the cabin of your vehicle, and within approximately ten seconds, press the "LOCK" button on your car remote. Put your Dodge key into the ignition. Where do you put the key in a Dodge? Insert your key into the Dodge ignition and turn the key to the "Run" position. You can leave the key there until the chimes in the car start...
Other

What happens if you have a bent valve in your car?

What happens if you have a bent valve in your car? Bent valves will not only damage pistons, but also valve guides, camshafts and valve train components. If the timing belt on your engine breaks while driving, serious internal engine damage may occur. This is particularly true if you car is equipped with an interference engine. What causes a bent intake valve push rod? If the intake valves push rod is bent the valve has come into contact with the piston and is very likely bent. If a valve has been adjusted with an incorrect clearance (too much clearance) or...
Easy lifehacks

What is a p0441 error code mean?

What is a p0441 error code mean? The error code P0441 or the Evaporative Emission Control System Incorrect Purge Flow is the set whenever the computer sees that there is a problem with the flow coming from the purge valve or the purge flow is not enough within the EVAP system. What causes OBDII code p0440? or loose. The fuel tank is leaking or damaged. or any component of the fuel vapor system. The fuel vapor pressure sensor is faulty. or damaged. The vent valve is defective. What does a code p0441 EVAP emission mean? The P0441 code is Evaporative...
Easy lifehacks

How to disengage the EVAP canister electrical connector?

How to disengage the EVAP canister electrical connector? 1. Raise the vehicle. Suitably support the vehicle. 2. Disconnect the EVAP canister vent valve electrical connector, if equipped. 3. Disengage the two vent valve pipe clips securing the pipe to the underbody. Remove the clips from the underbody and discard. 4. Disconnect the vent valve pipe at the EVAP canister. 5. How to install an Auxilary canister in a car? CANISTER INSPECTION AND AUXILARY CANISTER KIT INSTALLATION (SC184) SUBJECT: Auxiliary Canister Kit Installation: 1. Carefully detach the evaporative system canister close valve (CCV) wire harness clip (A). 2. Disconnect the CCV...