Easy tips

Why does the temperature gauge on my car read Cold?

Why does the temperature gauge on my car read Cold? If the temperature gauge still reads cold after the engine has warmed up, the gauge may simply be broken. Another reason the temperature gauge could read cold is if the thermostat in the vehicle stays open. What to do if your car's temp is too hot? If this still doesn't work, pull over on the side of the road, turn off the engine, open the hood carefully, and wait until the vehicle cools down. Never open the radiator cap while the engine is hot – coolant can spray and burn...
Other

What is the trouble code for cylinder 3?

What is the trouble code for cylinder 3? All our repairs are backed by our 12-month / 12,000-mile warranty. P0303 is a generic diagnostic trouble code (DTC) indicating an issue with the firing of cylinder 3. This code may be seen with other misfire codes as well as lean / rich condition codes. The P0303 DTC is set when the ECU detects multiple misfires from cylinder 3. What to do if you get an error code on your car? However, pinpointing the specific cylinder can be a complicated process without the assistance of the error code message. Therefore, if you...
Most popular

Is the 6.1 Hemi a good engine?

Is the 6.1 Hemi a good engine? The Hemi 6.1 Engine is a reliable, well-built engine that can deliver high mileage in excess of 250 000 miles, with regular services and maintenance. The Hemi 6.1 engine was based on the 5.7-litre engine but after being put on a strict diet. How many horsepower does a Chrysler 300C 6.1 SRT8 have? The Chrysler 300C 6.1 SRT8 has a V 8, Petrol engine with 6059 cm3 / 369.7 cu-in capacity. How many horsepower (hp) does a 2006 Chrysler 300C 6.1 SRT8 have? The 2006 Chrysler 300C 6.1 SRT8 has 431 PS /...
Most popular

What can cause a P0505 code?

What can cause a P0505 code? What causes the P0505 code? The idle air control (IAC) valve is carboned up and sticks or has limited control due to the carbon build up. The IAC passages are clogged or restricted with dirt, debris or carbon build up. When to use the p0507 code on your car? The P0507 code is triggered when the Engine Control Module ( ECM) detects that the engine is idling higher than the specified idle rpm range. The standard engine idle is usually between 600-800rpm based on the model of the vehicle. When is the p0507 idle...
Common questions

What kind of engine is in Chrysler 3.6 Pentastar?

What kind of engine is in Chrysler 3.6 Pentastar? Well, this 3.6-liter V6 has been around for a long time (almost 11 years), and for a good reason. The 3.6 Pentastar has high power for the V6 NA engine and is efficient and reliable. However, owners of these engines may face some common problems. Is there a cooling system for the Chrysler Pentastar? CHRYSLER 3.6 PENTASTAR 2012-2015 COOLING SYSTEMS SUMMARY: It has come to our attention at Sprintex, that Chrysler vehicles equipped with the Pentastar 3.6 V6 engine require special procedures to satisfactorily fill and bleed the engine cooling system....
Easy lifehacks

What would cause a Dodge Journey to overheat?

What would cause a Dodge Journey to overheat? While there are a variety of reasons your Dodge Journey is overheating, the most common 3 are a coolant leak (water pump, radiator, hose etc.), the radiator fan, or a failed thermostat. Does a 2009 Dodge Journey have two thermostats? YES! There are two thermostats on this engine. The primary t stat is located on the front of the water plenum in the thermostat housing coolant inlet. Why does my journey water pump keep overheating? If your radiator overflow is full (and you radiator fan is kicking on), it is very likely...
Most popular

How do you program a key fob for a 2010 Dodge Journey?

How do you program a key fob for a 2010 Dodge Journey? 2010 Dodge JourneyInsert First Programmed FOBIK. INSERT the first working FOBIK remote key into the Ignition and TURN it to the ON/RUN position.Remove First Programmed FOBIK. Insert Second Programmed FOBIK. Remove Second Programmed FOBIK. Program FOBIK Remote. Exit Programming Mode. Program Additional Remote. Test Remotes. How much does a key fob cost for a Dodge Journey? In short, replacing a Dodge Journey key can cost between $230 to $350. Does 2010 Dodge Journey have remote start? Product Description WHAT YOU NEED TO KNOW - This is a complete...
Easy tips

Why is my fuel pump relay outside the fuse box?

Why is my fuel pump relay outside the fuse box? If it’s located inside the engine bay, which can get hot from the engine’s heat, the heat can impede the relay’s performance. In addition, in the rare cases where you will find the relay placed in the engine bay but outside the fuse box, it will be exposed to heat plus dust and dirt. Where is the fuel pump in a car? The fuel pump is located in the fuel tank, near the rear of the vehicle and can usually be heard when the engine starts. A healthy fuel pump...
Most popular

How many gears does a Dodge Grand Caravan have?

How many gears does a Dodge Grand Caravan have? Used 2019 Dodge Grand Caravan Specs & FeaturesDrivetrainDrive typeFront wheel driveTransmission6-speed shiftable automatic Can a 3.6 Grand Caravan shift out of 1st gear? 2012 3.6 GRAND CARAVAN WONT SHIFT OUT OF 1ST GEAR Submitted:6 years ago. Category: Transmissions Show More Show Less Ask Your Own Transmissions Question Share this conversation Answered in 4 hours by: 2/26/2015 Transmission Mechanic: Chris (aka- Moose), Technician replied 6 years ago Chris (aka- Moose), Technician Category: Transmissions Is there a rebadged version of the Dodge Caravan? From 2009 to 2014, Volkswagen marketed the Volkswagen Routan, a rebadged version...
Other

Where does the power go to the Horn relay?

Where does the power go to the Horn relay? For a car horn to work properly, the vehicle must be equipped with a functioning horn relay. In most circuits, when the horn button (usually located in the steering wheel pad) is depressed, power is allowed to flow through the horn relay to the horn assembly. Typically, there is power supplied to the horn relay at all times. What causes a horn relay to go bad? Typically, there is power supplied to the horn relay at all times. Pushing the horn button completes the ground side of the circuit, pulling the...