Most popular

What should the timing be on a Chevy 383 Stroker?

What should the timing be on a Chevy 383 Stroker? Bring the engine RPM up to 2500-3000 RPM. Assuming that the centrifugal advance weights and springs have reached the maximum mechanical advance at the above RPM range (this can be adjusted by lighter or heavier combination of springs), set the timing at 32-38 degrees. Do not exceed 40 degrees. Is it correct for Chevy performance sp383 Stroker? From the posts and articles I've read, a lot of other sbc 383 (mostly street driven) seem to have positive results with a similar timing and advance curve set-ups when using a longer...
Common questions

How does an axle repair bearing assembly work?

How does an axle repair bearing assembly work? The axle repair bearing assembly replaces both the bearing and the conventional seal requiring no additional parts. The repair bearing moves the position of the bearing and seal so that they ride on an unworn section of the axle shaft. Where is the bearing seat on an axle? If the axle tube has a bearing seat on the inside of the axle tube, measure the depth from the outside edge of the axle tube to the inside seat and compare this to your repair bearing width. This measurement will ensure the repair...
Easy tips

What causes a car to have a check engine light?

What causes a car to have a check engine light? A loose gas cap, failing engine sensors, bad spark plugs, faulty valves such as in the EGR (exhaust gas recirculation) system, or intermittent misfiring could all be potential culprits. In this case, it's often best to take your car into a mechanic shop to get a diagnostic, or at the very least use an OBD reader yourself. Is there a way to turn off the Check Engine light? Do I need a special tool to turn off my check engine light? Yes. If you want to turn off your check...
Easy tips

Can a bad crank position sensor cause no spark?

Can a bad crank position sensor cause no spark? A bad Crankshaft Position sensor is a common cause of no starts. The signal from this sensor goes to the PCM or ignition module that switches the ignition coil(s) on and off. In ignition systems with a single coil and distributor, a bad coil or a cracked distributor cap or rotor can prevent the spark plugs from firing. How to know if your crankshaft sensor is working? 6 Most Common Crankshaft Position Sensor Symptoms 1 Check Engine Light Is On. 2 Vibrations in the Engine. 3 Slow Response from the Accelerator....
Easy lifehacks

What replaced the Chevy TrailBlazer?

What replaced the Chevy TrailBlazer? Traverse The Chevrolet Trailblazer or TrailBlazer is a mid-size SUV produced by Chevrolet, a division of General Motors. The nameplate was first used in North America from 2001 to 2008, when it was replaced by the Traverse crossover SUV in 2009. When did the Chevrolet TrailBlazer EXT come out? Chevrolet’s midsize TrailBlazer sport utility vehicle debuted early in 2002 as a five-passenger vehicle. It was soon joined by an extended-length TrailBlazer EXT with a seven-passenger capacity. How tall is a 2006 Chevrolet TrailBlazer EXT? The TrailBlazer EXT is 207.8 inches long overall and rides on...
Common questions

Why does my Chevy Silverado make a hissing noise when I press the accelerator?

Why does my Chevy Silverado make a hissing noise when I press the accelerator? I have a 2004 Chevy silverado 1500 with a 5.3. It recently started making a hissing noise or kind of a sucking air noise coming from the drivers side of the engine like by the intake when you press the accelerator. I just got the intake gasket changed still didn't fix it does anybody know what this could be? Man if you figure it out, post it up! Why does my master cylinder make a hissing noise? If the silencer has degraded or been damaged, you’ll...
Easy lifehacks

How do you change the alternator on a Toyota?

How do you change the alternator on a Toyota? How to Change the Alternator in a Toyota. Loop the belt around the alternator pulley and then tighten down the adjusting bolt until the belt is tight. Install the lock bolt on the adjusting bolt using an open-end wrench. Then tighten the pivot bolt using the 3/8-inch ratchet and socket. Do you need to remove serpentine belt to change alternator? As you loosen the bolts, the alternator will slide in the bracket under the tension of the belt. You may not need to remove the serpentine or accessory belt if it’s...
Easy tips

Where is the brake light switch on a car?

Where is the brake light switch on a car? When the brake pedal is pressed, it closes the switch, and the current flows through the wiring to the brake lights. This turns on the rear brake lights. The brake light switch can also be located on the master cylinder. Hydraulic pressure from the master cylinder brake light switch system can close the switch to turn on the brake lights. What happens if you have a bad brake light switch? The brake light switch on modern vehicles is no longer a simple switch used to turn on the brake lights. A...
Other

What should I do if my igniter switch is not working?

What should I do if my igniter switch is not working? Continued onto the Newark showground for a rally, and found someone who knew what to do as a temporary fix. Take the vent cover off (quick release) and use a long handled gas lighter (like the BBQ ones) with gas turned on, and flash the gas lighter at the igntion point tubeto ignite the gas flow. Replace cover and it works. What happens if you turn off the igniter on a refrigerator? Even if no 12V or 230V power is being provided to a Powerfridge, unless the energy selector...
Most popular

What should I do if my oil pressure is zero?

What should I do if my oil pressure is zero? If the oil pressure is at zero, then the oil pump has failed and needs replaced or the pickup tube has too much buildup and preventing flow to the oil pump, which will damage the oil pump. Even if a bearing failed, there will still be oil pressure. I recommend replacing the oil pump on the engine and cleaning out the pickup tube. What happens to an engine with low oil pressure? If this happens too often, the bearings play will get too big and the oil will just pour...