Easy lifehacks

What are the 85-92 TBI instructions for fuel injection connection?

What are the 85-92 TBI instructions for fuel injection connection? 85-92 TBI Instructions FUEL INJECTION CONNECTION.COM 85-92 TBI Instructions 1985-1992 Throttle Body Injection Wiring Harness Installation Quality of Construction This harness is constructed using OEM quality wire for superior reliability and long term use. What are the instructions for fuel injection connection? FUEL INJECTION CONNECTION.COM 85-92 TBI Instructions 1985-1992 Throttle Body Injection Wiring Harness Installation Quality of Construction This harness is constructed using OEM quality wire for superior reliability and long term use. The wire colors are the same as the factory wire colors for car and truck TBI injected...
Easy tips

What happens if you have a coolant leak in your car?

What happens if you have a coolant leak in your car? If your car is leaking coolant, it will run normally until the coolant level gets too low. Once it is low, there will not be enough coolant to keep your engine at the normal operating temperature and the engine will overheat. If your engine overheats, it can cause significant damage to the block, heads and other components. Can a worn radiator cap cause coolant to leak? A worn, weak, or leaking radiator cap will not hold pressure, lowering the boiling point and allowing coolant to boil out. It may...
Easy lifehacks

What are the starter bolt holes on a Suburban 1500?

What are the starter bolt holes on a Suburban 1500? 1996 suburban 1500: flywheel..block..cracked..the starter bolt holes i have 1996 suburban 1500 5.7, that i bought with a bad flywheel ok i changed the flywheel and starter. come to find out the block is cracked where the starter bolt holes are. the bolt pattern are dia… Why does my Chevy Silverado sound like a flywheel? flywheel by hand to see if you can see a loose bolt. Sometimes you can actually get a little movement of the flywheel just before the torque converter moves. Kind of like slop. Pretty hard...
Common questions

How do you Bleed brakes on a 1998 Chevy Silverado?

How do you Bleed brakes on a 1998 Chevy Silverado? Running the pedal to the floor can rip the internal lip seals on that corrosion. You're going to have to pump the pistons out of the calipers until the pads contact the rotors. Until that happens you will also be able to push the pedal more than half way. Be careful to just keep pumping it only half way until it gets firm. Is it possible to bleed the brake system? Bleeding the brake system after changing the brakes can be hard on some anti-lock braking systems. The good news...
Other

How much was a Camaro in 1992?

How much was a Camaro in 1992? How much is a 1992 Camaro RS worth?CoupeOriginal MSRP / PriceEngineCamaro 2dr Coupe RS$12,075 / N/A6 Cylinder / 8 CylinderCamaro 2dr Coupe Z28$16,055 / N/A8 Cylinder Where did the 1994 Chevy Camaro get its name? 1994 Chevrolet Camaro Coupe The name Camaro was reportedly derived from Heath's French and English Dictionary as a term that translated to ''friend'' or... More Gateway Classic Cars of Philadelphia is presenting a 1969 Camaro for sale. This Orange and White Camaro with Black interior with classic Chevy RS... Where can I buy a 1969 Chevy Camaro? Gateway...
Easy lifehacks

What should I do if my valve lifter is making noise?

What should I do if my valve lifter is making noise? Flush out the old oil. Unscrew the cap under the car and place a container or bowl under the cap. Rinse your valve lifter with an engine flushing agent like Liqui Moly Engine Flush after the leaking of oil has stopped. Pour the new oil according to your engine specifications. This is probably the best solution to avoid noise from lifters. Why does my lifter make a noise when I start the engine? Usually, the noisy lifters produce some sort of tapping noise during the first few seconds after...
Easy tips

What did it mean when your truck cut off?

What did it mean when your truck cut off? I was driving and the truck cut off. it was like I ran out of gas. I though that the safety switch tripped so I checked that and it was ok. Why did my truck engine shut off going down the road? That was because the top started to rust out, not from failure. When it went in my 98, I was out hunting and it died driving down the road. Replacing it on the truck wasn't bad, I didn't even attempt it on the Yukon. Try crawling under the truck...
Easy lifehacks

How to know if the EGR valve in the 1994 Chevy is bad?

How to know if the EGR valve in the 1994 Chevy is bad? It's important to check the EGR valve regularly to make sure that it is working properly and does not need to be replaced. Park the Chevy and let it sit for a half hour. This will ensure that the components are cool and prevent potential burns. Open the hood of the vehicle and locate the EGR valve. What causes a rough idle with an EGR valve? Rough idle. One of the most common symptoms of a problem with the vehicle’s EGR valve is a rough idle. It...
Common questions

When was the GM 350 crate engine retired?

When was the GM 350 crate engine retired? It was eventually retired in 2003, but now it’s back. In its press release for the new crate engine, GM says that the 350 has been given a brand-new main block, a new cylinder head, new valve covers and even ‘race-proven’ forged steel crankshafts. Race-proven, nice. Can you break in a Chevy crate engine? The most important thing you can do for your car and your new crate engine is properly break in the engine. Ignoring this critical part of installing your new engine will likely wreck it, costing your sanity and...
Other

What is distributor gear material?

What is distributor gear material? Distributor Gear Materials:Cast Iron.Composite (offers great life, conforms well to the mating cam gear, and is compatible with ANY camshaft gear material)Melonized or hardened steel. (material that OEMs use with factory roller cams; many aftermarket. Bronze (conforms well to the mating. Do MSD distributors come with Melonized gears? The melonized gear is still available from GM and ACDelco. Fortunately MSD now sells a melonized gear for 0.500-inch shaft Chevy distributors (MSD PN 8531). What do you need to know about gear inspection? The composite test of a gear is a method of inspection in which...