Easy lifehacks

How does the vssb work on a GM car?

How does the vssb work on a GM car? In the same fashion if gear ratios or tire sizes are changed, the module may be quickly swapped or reprogrammed for the correct ratios. The unit takes input from the transmission VSS (Vehicle Speed Sensor) to derive pulses per mile, according to the rotation of the transmission tailshaft. What was the vssb / DRAC used for in 1989? If you find something incorrect or wish to contribute something, just let us know here . The external VSSB/DRAC (Vehicle Speed Sensor Buffer / Digital Ratio Adapter Controller) module was used in 1989-1995...
Easy tips

Will a v6 4L60E transmission fit a V8 Chevy?

Will a v6 4L60E transmission fit a V8 Chevy? The 4L60E in the NNBS is identical except the harness in 2009-2013. 2007.5-2008 are the exact same regardless if is v6 or v8. The converter or flexplate may be different tho. Why is my 4L60E not shifting into 4th gear? Below are some common things that fail in the 4L60E and cause this problem. It probably goes without saying, but if you put the vehicle into second gear manually, you’ll still be able to get to where you need to go. If you end up with a bad sprag, the 4L60E...
Easy lifehacks

What was the quarter mile time for a 1987 Buick Grand National?

What was the quarter mile time for a 1987 Buick Grand National? 13.4 sec Officially, Buick claims a 0-60 mph time of 5.4 sec for the GNX versus their Grand National number of 6.9. Through the quarter mile, the GNX clocks 13.4 sec to 104.0 mph against 15.7 at 97.5. How much was a Buick Grand National in 1987? The car had a sticker price of $29,389 in 1987. It was number 308 of 547 GNXs ever built, and it sat at Boulevard Buick of Signal Hill, California, for more than 30 years. How much horsepower did the 87 Buick...
Easy lifehacks

What are the PCM connectors for a 1998 Chevy S10?

What are the PCM connectors for a 1998 Chevy S10? Blue c1 1998 99 in this article youll find the pin out descriptions of the 4 pcm connectors for the 1998 1999 gm 43l 50l or 57l engines. For other pcm pin out charts take a look at the following. These are the red blue pcm connector pinouts that will cover 1999 to 2002 485360. Assortment of chevrolet s10 wiring diagram. What are the PCM pins for 1999 to 2002? These are the RED & BLUE PCM connector pinouts that will cover 1999 to 2002 4.8/5.3/6.0. Your harness MAY NOT...
Most popular

How long does it take to accept an answer?

How long does it take to accept an answer? Only one answer at a time can be the "accepted" answer. There's a brief period ( 15 minutes) immediately after asking the question when you can't accept any answer. You may change which answer is accepted, or simply un-accept the answer, at any time. Where can I get answers to my questions? So, when there are some points needed to be explained, we offer you our help. No matter whether you have questions in in math, physics, programming, economics, chemistry, biology or English, post them here and find a well-formulated answer...
Other

What does tow mode do Silverado?

What does tow mode do Silverado? In short, the tow haul mode protects your transmission when hauling heavy loads. This tow haul mode will adjust your Silverado's transmission shift patterns, reducing the number of shift cycles. Tow haul mode enables you to take better control of your vehicle while hauling heavy loads up and down steep terrain. Why does my 2003 Chevy Silverado not start? My 2003 Silverado has issues starting sometimes. If I hit the steering column it will sometimes start. My silverado has left me stranded numerous times with this intermittent starting bullsh!t. The truck starts majority of...
Easy tips

What should I do if I have a bad starter relay?

What should I do if I have a bad starter relay? They can also be hazardous and can cause damage. If you run into symptoms of a bad starter relay or solenoid with your car, truck, or SUV, make sure to have a trusted technician to diagnose the specific problem. This article is intended only as a general guidance document and relying on its material is at your sole risk. When do I need to replace my solenoid starter? When this is the case, it may be necessary to replace the entire starter when the solenoid goes bad. Sometimes the...
Other

How big is the front door grab handle?

How big is the front door grab handle? Grab Handle, Front Driver Interior Door Position, Plastic/Rubber, Gray, Chevy, GMC, Each Part Number: RNB-80371 More Detail... Interior Door Pull Handle, Tan, Left Side, Each Part Number: RNB-80415 More Detail... Door Grab Handle, Interior, Rubber, Black, 0.71 in. Width, 12.40 in. Length, Each Part Number: RNB-77202 More Detail... How to get free shipping on interior grab handles? All qualifying parts must be on ONE INVOICE. Minimum order value $149.99 required (per single invoice) and excludes non-Omix-ADA family family brand products, tax, freight or other charges (merchandise value only). Maximum Rebate $200 per...
Most popular

Why did I lose all my self confidence?

Why did I lose all my self confidence? Some of the many causes of low self-esteem may include: Unhappy childhood where parents (or other significant people such as teachers) were extremely critical. Poor academic performance in school resulting in a lack of confidence. Ongoing stressful life event such as relationship breakdown or financial trouble. What can destroy your confidence? 17 Ways You're Destroying Your Confidence and Don't Know ItExcessive Apologizing. The Way You Dress. Over-Complimenting Others. Saying "Yes" to Everything. Obsessing Over Minor Flaws. Ignoring Your Feelings. Letting Others Make Your Decisions. Using "Always" And "Never" How do I get...
Common questions

Can I tighten my pitman arm?

Can I tighten my pitman arm? A couple of ways to tighten it would be to use an impact to run the nut down or if you don't have an inpact, use a BIG set of channel locks and squeeze the pitman arm and center link together as you tighten the nut. As it gets tighter the taper will cause enough friction to tighten it all the way. What is the torque on a pitman arm? Somewhere around 180-210 ft/lbs on the pitman nut. How do you adjust the torque on a pitman arm? Tighten the adjusting nut on top...