Easy tips

What is an Opda on a Jeep?

What is an Opda on a Jeep? The Crown Automotive Oil Pump Drive Assembly (OPDA) for the TJ Wrangler replaces the factory unit which was designed with two oil impregnated bronze bushings separated by an oil seal. The upper bushing is cut off from lubrication by that seal, resulting in premature failure. What causes a worn oil pump drive assembly? An oil channel was also added to the shaft to increase overall lubrication to the area. A worn oil pump drive assembly will show symptoms, such as a check engine light or a squeaking noise coming from the oil pump...
Easy lifehacks

How do you wire 4 wires to 3 wires?

How do you wire 4 wires to 3 wires? Connect the ground wire of the 3-wire cable to the ground wire of the 4-wire cable. Connect the black wire of the 3-wire circuit to either the red or the black wire of the 4-wire circuit. The red and black wires are the"hot" wires. Either wire can be used to power a circuit. How do you test a 4-wire trailer harness? How to Test a 4-Prong Trailer Connector PlugTell your helper to turn on the ignition while you go to the connector plug. Tell your helper to turn on the right...
Most popular

What happens if you install bigger tires on your car?

What happens if you install bigger tires on your car? When you put bigger tires on your car, SUV, crossover, or light truck, you raise the vehicle's clearance — increasing body roll and load transfer, which may negatively impact your car's balance and speed. What happens if you increase tire size on Dodge Ram? First, make sure that if you reduce the wheel size, you can clear the brake calipers. Second, if you increase the wheel and tire size, a spacer must be used to avoid rubbing the fender walls when turning. What are the dimensions of a Dodge Ram...
Most popular

How to install a 7 pin trailer plug?

How to install a 7 pin trailer plug? New 7-pin plug ready to install on trailer cord. Step 1: Remove old plug. Step 2: Replace with better plug. It really is that simple. Get yourself a good 7 pin trailer plug. How do you replace a 7 pin plug? Use wire strippers to remove the shielding from each wire. The length of copper to expose may differ depending upon your replacement plug. I trimmed back approximately 1″ off each wire, and removed enough rubber shielding to allow me to easily manipulate each colored wire into the new plug. Can a...
Common questions

Why is there no noise cancellation on Dodge Ram?

Why is there no noise cancellation on Dodge Ram? What happen is like a feedback, increasing some frequencies to the audio system cause this issue. The "solution" is canceling this feature, in this case the microphones, in hondas the microphones as well in gmc and Cadillac cutting the speed sense wire that go to the factory amplifier. Is the black ram Bighorn making a humming noise? Hello, I purchased my beautiful black Ram Bighorn in May 2018 and to date have logged 5500 frustrating miles on it. It seems this truck is plagued with the familiar loud intermittent humming noise....
Other

How much is a push start key?

How much is a push start key? Is it expensive? Well yes, it can be, because of the newer technology. Dealers can and do charge usually between $350 to $900 for them! What was the first key to start a car? Chris Amos and Roy Ritchie 1949 Chrysler: While the first key that turned on a car’s ignition arrived in the early 20th century, it required the push of a button to engage the starter. In 1949, Chrysler introduces the modern key that starts the car with a turn of the ignition tumbler. How can I program a new car...
Most popular

How do you turn off emergency blinkers on a Honda?

How do you turn off emergency blinkers on a Honda? How to Turn Off Hazard Lights on a Honda AccordLocate the hazard warning light control positioned in between the two center vents on the dashboard.Press the hazard button to engage the four-way flashing emergency lights. Press the hazard button a second time to turn the flashing emergency lights off. How do I turn off my hazards? Here's how to use them:Locate the hazard switch on the dash.Push the switch to turn on the hazard lights. All four turn signals will start flashing.Push the switch again when you need to turn...
Common questions

How do you change a transmission position sensor?

How do you change a transmission position sensor? How it's done:The faulty transmission position sensor switch is identified.The vehicle is lifted and supported on jack stands.The defective transmission position sensor switch is then removed.The new transmission position sensor switch is installed and the vehicle taken off the jack stands. How do you remove a transmission position sensor? Grab a creeper, flashlight, and tools for the job. Go under the vehicle and locate the transmission position sensor (switch). Step 3: Remove the harness from the sensor. If you have a mechanical shifter, you will need to remove the linkage from the...
Common questions

Why is my steering wheel dependent on a clock spring?

Why is my steering wheel dependent on a clock spring? Because the airbag in your steering wheel is dependent on a functional clock spring, it’s crucial that the clock spring is in good working condition. Keep reading to understand how a clock spring works, what symptoms of a broken clock spring are, and the average replacement cost is. What is a Clock Spring? What Does a Clock Spring Do? Can a power steering module work like a radio? IIRC, the manual calls for a calibration procedure when things like that are replaced. But it may fall into an area were...
Easy lifehacks

Does trailer brake controller drain battery?

Does trailer brake controller drain battery? Brake Controller has Constant Power Output and is Draining the Battery on the Truck Brake controllers do send a little power back to check for a trailer but it should not be that much. You will either have an issue inside the brake controller or there is a short somewhere else that is causing a draw. Where to plug in a trailer brake controller? Disconnect the negative cable, and move it to the side. Even if your vehicle doesn’t have a factory connector for plugging in a brake controller, it should have blunt-cut brake...