Most popular

Are there any problems with the Ford Focus fuel pump?

Are there any problems with the Ford Focus fuel pump? Other Common Gasoline Fuel System related problems of Ford Focus Problem Category Number of Problems Fuel Pump problems 335 Gasoline Fuel System problems 131 Tank Assembly problems 61 Fuel Delivery problems 54 How to replace a fuel pump in 90 minutes? HOW TO REPLACE A FUEL PUMP IN 90 MINUTES! - Ford Focus 1999-2007 - YouTube HOW TO REPLACE A FUEL PUMP IN 90 MINUTES! - Ford Focus 1999-2007 What happens when a fuel pump goes bad? The engine turns off if the combustion chamber’s fuel is inadequate or doesn’t...
Other

Can you connect a subwoofer to a vintage amplifier?

Can you connect a subwoofer to a vintage amplifier? A subwoofer with speaker-level inputs is especially easy to connect to your older amplifier or receiver! To do so, just connect to the speaker outputs on the source unit using speaker wire and then to the matching inputs on the subwoofer. You can even power speakers from the amp or receiver at the same time. How do you hook up a subwoofer to an amp without subwoofer? Right: An RCA Y adapter that can be used with a line level converter to connect to a subwoofer with a single RCA input...
Easy tips

How many gallons of oil does a 2000 7.3 take?

How many gallons of oil does a 2000 7.3 take? “How many gallons of oil does a 7.3 Powerstroke hold?” Well, 4 quarts to a gallon means you're going to need almost 4 gallons of oil to perform a full 7.3 Powerstroke oil change. How much oil does a 2000 F250 take? 15 quarts Engine OilViscosity:0W-30 (Below -18) 10W-30 (-23 To 32) 15W-40 (Above -12) 5W-30 (Below -1)Capacity:15 quarts (with filter)When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase. After refill, check oil level. Top off to proper level as needed.Torque:Oil Drain Plug...NS ft/lbs...
Other

How do you reattach a snap button?

How do you reattach a snap button? When repairing or fixing snaps, minimal hand sewing is required.Place the fabric right side up on a flat surface and insert the flathead screwdriver between the top and base of the socket closure: the socket and stud.Insert the screwdriver between the fabric and the stud. Lift the screwdriver until the snap pops off. How do you remove reuse snap buttons? To remove our standard prong snaps, gently twist a small headed screwdriver back and forth all round the outermost lip of the socket or stud to loosen the prongs from the snap component....
Other

How does a torque converter lock up in a transmission?

How does a torque converter lock up in a transmission? Torque converter lock-up is engaged through a solenoid mounted inside the transmission. When the solenoid is energized it redirects the fluid flow back through the input shaft to put pressure against the clutch assembly allowing it to engage with the front of the torque converter. What's the difference between lock up and non lock up transmission? Towing will add heat to the transmission. A non-lock-up torque converter will add more heat. With a lock-up when you get to speed, the torque converter will lock-up, which creates a direct drive from...
Common questions

Does my F150 have an alarm?

Does my F150 have an alarm? The F-150 comes with a factory-installed alarm system. It's important to learn the proper way to use the alarm system, including disabling it when needed. Is there an alarm on a Ford F-150? The Ford F-150 is a full sized pickup truck. The F-150 comes with a factory-installed alarm system. The alarm is designed to go off anytime someone tries to enter the locked vehicle. How to disable the anti theft system on my 2000 Ford F150? However, you can deactivate the autolock feature. This security feature automatically locks all the F-150's doors when...
Most popular

How to remove a 1993 to 1996 power antenna mast?

How to remove a 1993 to 1996 power antenna mast? Figure 1: This illustration shows the special nut and grommet positioning for the 1993 to 1996 Power Antenna Mast setup. It also shows which direction to turn the special nut to remove it. Once the nut and grommet are removed, turn the radio on. How do you replace a broken radio antenna? You can replace the broken car radio antenna and install a new radio antenna with these simple methods. How to replace a broken car radio antenna? You can replace a broken car radio antenna by unplugging the coaxial...
Easy lifehacks

How to install a fuel injected 5.0 in a Mustang?

How to install a fuel injected 5.0 in a Mustang? The purpose of this page is to describe the wiring modifications necessary to install a 87-93 SEFI 5.0 into an early model Mustang. These are the steps I went through to run the motor shown to the right. Your install may vary.... Computer Install: Location of the computer is critical to determine wire routing. Can a fuel injected 5.0 harness be modified? Harness Modification: To modify an existing harness, get one that is complete and unmolested. It should include: Injector loom (the small harness that connects the injectors and sensors...
Other

What does a lit engine temperature symbol mean?

What does a lit engine temperature symbol mean? Engine Temperature Warning A lit engine temperature symbol indicates that the engine’s temperature has risen above the ideal range. This may light up for a variety of reasons. Check coolant level, radiator cap, fan operation; and look for coolant leaks. 11. Transmission Temperature Warning What does a red stop Engine Lamp mean? Will flash for 30 seconds at key ON if maintenance is due. Malfunction Indicator Lamp (MIL) Lights up to warn the driver to schedule service soon. May light up in addition to other lamps. Red Stop Engine Lamp Indicates that...
Other

How much does it cost to fix car injectors?

How much does it cost to fix car injectors? Depending on your make and model, you can usually expect to pay around $800 to $1,450 for a complete fuel injector replacement. Parts alone are about $600 to $1200 and the labor cost will run about $200 to $250. How much does an injector replacement cost per hour? So lets to the math $980-250 for the injector = $730 for labor divided by 4 hours =$182.5 per hour ( actually the shop should be able to do it less that 4 hours.) Even if the did the updated stand pipe and...