Other

How do you remove the battery from a Jeep Grand Cherokee?

How do you remove the battery from a Jeep Grand Cherokee? How to Remove a Jeep Cherokee BatteryTurn off the engine. Pull the hood release latch, located next to the driver's-side seat, inside the vehicle.Use the wrench to loosen the nuts that holding the cables to the battery's terminals. Loosen the black (negative) one first. Carefully lift the battery out of its place. Why did my Jeep Grand Cherokee lose power steering? Tl-the contact owns a 2016 Jeep Grand Cherokee laredo. The contact stated that while driving approximately 30 mph, the vehicle started to vibrate, lost power steering and the...
Easy lifehacks

Can bad gas cause issues?

Can bad gas cause issues? Bad gas can form deposits that can cause issues in your engine. Again, this is very rare and probably won't happen, but it's good to know. However, if you get bad gas from a gas station, you could be in for quite the repair bill. How do you tell if you filled up with bad gas? Signs Your Car Has Bad GasDifficulty starting up.Rough idling.Pinging sounds.Stalling.Check engine light illumination.Reduced fuel economy.Higher emissions. What happens if you have bad gas in the tank? If there is only a small amount bad or old gas in the...
Easy tips

What happens when a drive support bearing fails?

What happens when a drive support bearing fails? A failed bearing is unable to support the driveshaft, and as a result the driveshaft will flex, causing a vibration and shuttering sensation that can be felt throughout the vehicle when it's broken. How do you remove a front drive support bearing? The front driveshaft is going to be attached solid inside the output shaft supports. In order to remove the driveshaft, you'll need a rubber or plastic tipped hammer. On the front of the driveshaft is a welding mark that is solid and is the best place to hit with the...
Common questions

Are there any Mitsubishi parts that are genuine?

Are there any Mitsubishi parts that are genuine? Mitsubishi Genuine Parts and Accessories are engineered and manufactured to ensure a perfect fit and optimal performance for your vehicle. Along with using Mitsubishi Genuine Service, it's the best way to protect your investment for the long run. High quality replacement parts at an affordable price. Which is not covered by the Mitsubishi warranty? Mitsubishi Genuine Parts & Oil *The repair of damage caused by the parts or services not prescribed by the Warranty and Maintenance Manual (such as using non-genuine parts or excessive oil change intervals), is not covered under warranty....
Other

How many Dodge Charger Super Bees were made in 2007?

How many Dodge Charger Super Bees were made in 2007? of torque, the 2007 Dodge Charger SRT8 Super Bee was the first special edition Charger from SRT. Only 1,000 units were built for the 2007 model year. What is a 2007 Dodge Charger Super Bee worth? Restored examples can be bought today between $80,000 – $100,000. As the latest edition in American muscle sedan, the 2007 Dodge Charger SRT-8 Super Bee will be available in dealerships this fall. What is a Dodge Charger Super Bee? The Dodge Super Bee is a mid-sized muscle car marketed by Dodge, that was produced...
Easy tips

Should steering wheel return to center?

Should steering wheel return to center? Sticking or binding components, such as a king pin, ball joint, bell crank or even the steering column can prevent the steering wheel from returning to center after a turn. Alignment can also be a factor; improper caster, and to some degree, improper toe-in, can be contributing factors. Is there a jerk in steering while turning? Enter your ride HERE to be a part of this month's Ride of the Month Challenge! I am experiencing and suttle jerk in the steering when turning. It almost feels like it would if you were trying to...
Easy tips

How long has Navtec hydraulics been in business?

How long has Navtec hydraulics been in business? Hiring the best of the original Hydraulics personnel, Navtec Hydraulics now has over 70 years of combined experience in building Navtec Hydraulics. Not surprisingly, every aspect of the business has improved since the focus and concentration is now on one product and one product only. Who is the importer of Ram Trucks in Australia? Ram Trucks Australia are the only Fiat Chrysler Automobiles (FCA) authorised importer and distributor of Ram Trucks for both the Australia and New Zealand markets. As at today, we are the only FCA authorised full-volume manufacturer of right-hand-drive...
Common questions

When did the Dodge Neon SRT 4 come out?

When did the Dodge Neon SRT 4 come out? The Dodge Neon SRT-4 is a sport compact car manufactured by Dodge from 2003 to 2005. A turbocharged variant of the Neon, the car was developed by DaimlerChrysler 's in house PVO (Performance Vehicle Operations) tuner group. PVO was officially renamed SRT ( Street and Racing Technology) in 2004. When did the Dodge Neon stop being called a neon? Dodge removed the “Neon” designation from the vehicle in 2004, marketing the car simply as the “SRT-4”. In 2005, an American Club Racer (ACR) package and limited edition numbered Commemorative version of...
Common questions

Is there a 2005 Ram 2500 for sale?

Is there a 2005 Ram 2500 for sale? I have for sale a 2005 Ram 2500 Laramie with the 5.9L Cummins , Truck is super clean inside and out runs and drives like new completely stock never been chipped. I am the second owner, this truck has been meticulously maintained no leaks or blow by at all, truck needs nothing This has been a very dependable truck over the years. New tires. What kind of engine does a Dodge Ram 2500 have? 2005 Dodge Ram 2500 Rust free. Diesel. 2 wheel drive. 6 speed std. 2005 Ram 2500 Laramie with...
Other

How to retrieve car trouble codes with no equipment?

How to retrieve car trouble codes with no equipment? If the link has 12 ports rather than 16, connect ports "A" and "B" with a paper clip or jumper wire. Watch the "Check Engine" light for codes as documented previously. How to retrieve a Toyota engine trouble code? • Locate the check connector under the hood and identify the T (TE1 on late model TCCS) and E1 terminals. • Turn the ignition switch to the "on" position and make sure that the check engine light is on. • Confirm that the throttle is closed (IDL contact on). • Jumper check...