Easy lifehacks

How long does it take to drive 1000 miles in one hour?

How long does it take to drive 1000 miles in one hour? 1000 miles divided by your speed will give you the time it takes to drive that distance. So if you drive 65 miles an hour, 1000 miles divided by 65 miles an hour will result in a time of 15.38 hours or 15 hours and 22.8 minutes. How long does it take to drive a mile at 70 mph? An hour is 60 minutes and a minute is 60 seconds. So, an hour is 3600 seconds. One seventieth of that is 3600 / 70 = 360 / 7...
Most popular

How far is Asheville from Knoxville?

How far is Asheville from Knoxville? Distance from Knoxville, TN to Asheville, NC There are 80.80 miles from Knoxville to Asheville in southeast direction and 116 miles (186.68 kilometers) by car, following the I-40 route. Knoxville and Asheville are 1 hour 59 mins far apart, if you drive non-stop . How far apart is Knoxville and Gatlinburg? 37.9 miles How long is the drive from Knoxville to Gatlinburg? The direct drive from Knoxville to Gatlinburg is 37.9 miles (61 km), and should have a drive time of 53 mins in normal traffic. Is Corpus Christi close to Fort Worth? Fort...
Easy lifehacks

What happens when an engine is seized by lack of oil?

What happens when an engine is seized by lack of oil? Seized engines due to lack of oil can range from a little engine damage to major damage. An engine can seize from not running, too. In that case, it’s a little different. The piston rings ‘freeze’ against the cylinder walls from rusting. What happens if you don't put oil in your car? It will suddenly sound rough and stop on its own. Seized engines due to lack of oil can range from a little engine damage to major damage. An engine can seize from not running, too. In that...
Most popular

Why does my steering wheel vibrate when I turn the car on?

Why does my steering wheel vibrate when I turn the car on? The cause of the steering wheel vibration may also be an engine malfunction. This is a very complex operation and there are many reasons why this can cause this movement, such as problems with spark plugs, which may prevent the appropriate levels of air to the engine, among other potential faults. Why does my steering wheel shake when I turn a corner? If you feel the steering wheel is vibrating when you make the turn around the corner but not when you drive straight, it means the problem...
Most popular

Can you put a turbocharger on a 4 cylinder?

Can you put a turbocharger on a 4 cylinder? Many four cylinder sports cars now come equipped with turbochargers. Installing an aftermarket boost controller on the vacuum line between the turbocharger and waste gate can allow you to increase the amount of boost the turbocharger produces. Can you add a turbo to a supercharged engine? Yes. You can Use both. The concept of supercharger and Turbocharger are slightly different. If you use only supercharging(without turbo charger) it consumes roughly 3-5% of power develloped by the engine however sp power devloped by the engine and other performance factors like volumetric efficiency...
Common questions

Are there any faults in the Jeep AW4 transmission?

Are there any faults in the Jeep AW4 transmission? Diagnosis of faults in the Jeep AW4 transmission. The automatic transmission used in the Jeep XJ Cherokee is nearly bullet proof. Seldom does it ever give trouble. Maybe that is why it is so hard to find good information on how to fix it when it occasionally does act up. How does the torque converter work on a jeep AW4? Normally, the transmission with switch to 2nd at 20 to 25 mph depending on the TPS signal. It gets its speed reference from the internal speed sensor so if you are...
Other

How to interpret mold spore counts from EAA, Inc?

How to interpret mold spore counts from EAA, Inc? 74 Commentson Interpreting Mold Spore Counts from EAA, Inc. Mold Spores Taking air samples for mold spores is easy. Knowing how to interpret the laboratory results is another matter. There is no one level of mold that can distinguish a clean and moldy building. Outdoor spore types and concentrations have an important influence on the indoors. What was the number of people exposed to mold? Aspergillus/Penicillium in mold contaminated buildings the figure was 36,037. Also see MOLD EXPOSURE STANDARDS to see what "acceptable mold level" standards have been recommended by different...
Common questions

Is the 5.7 Hemi a good motor?

Is the 5.7 Hemi a good motor? Is The 5.7 Hemi A Good Engine? Overall, the 5.7 Hemi is an outstanding engine. It has earned a reputation as a reliable and sturdy workhorse of an engine. If you talk to anyone that owns a vehicle with a 5.7 Hemi engine, they will likely have very few, if any, bad things to say about it. When did Dodge Ram 5.7 Hemi come out? Ram Year: 2004. Engine: Hemi 5.7. All the 5.7 hemis have the same block, crank, and pistons. They have different front covers, different heads, and different air intake...
Other

When did Dodge first use Cummins?

When did Dodge first use Cummins? 1989 Dodge masterfully engineered the RAM to accommodate the size and power of the Cummins turbo diesel engine, and the first Cummins-powered RAM hit the streets in 1989. With 400 pounds-feet of torque, it roared past the competition. This was the start of a powerful relationship which has grown through the years. Who makes diesel engines for Dodge? VM Motori The EcoDiesel, developed and manufactured by VM Motori (a Chrysler supplier since 1992), is one of the most advanced diesel engines in the marketplace. Equipped with a diesel oxidation catalyst, diesel particulate filter and...
Easy lifehacks

Why does my golf driver make a rattling sound?

Why does my golf driver make a rattling sound? Small particles can come loose from inside the driver head resulting in a rattling sound. If the nosie is instead coming from the shaft, it’s likely pieces of epoxy glue are causing the rattling sound. In most cases rattling won’t negatively affect a golf shot. Why does my iron driver make a rattling noise? Unlike wedges or drivers, the rattle in iron might not be caused by the epoxy glue getting loose. Although, the glue in the shaft might have become a bit loose and move up and down the shaft...