Easy tips

Can you not depress brake pedal?

Can you not depress brake pedal? Depress the brake pedal means to push down on the pedal. The same way you do when you brake to bring the car to a stop. If you are doing that but still get the waring, you may have a bad brake switch. To make the brake pedal sad and feel like it has no purpose. Why does the brake pedal won't go down? Upon further inspection, it appears the master cylinder on the brake was leaking. This could be the issue..........overnight fluid seeps in and makes the brake impossible to push. After some...
Easy tips

What does p0068 code on Dakota Durango mean?

What does p0068 code on Dakota Durango mean? Ok basically what that means is that the reading from the MAP sensor is not jiving with the reading from the Throttle Position Sensor. What are the possible causes of a p0068 code? P0068 Possible Causes. Faulty Mass Air Flow (MAF) sensor. Large vacuum leak. Leaking air duct system. Mass Air Flow (MAF) poor electrical connection. Manifold Absolute Pressure (MAP) poor electrical connection. Why is the p0068 throttle position sensor inconsistent with the mass? If during a self-test, the comparison of the TP sensor and MAF sensor readings are not consistent with...
Easy lifehacks

Is it possible to find number of days between two dates?

Is it possible to find number of days between two dates? Most of the answers using UNIX timestamps (and 86400 to convert that to days) make two assumptions that, put together, can lead to scenarios with wrong results and subtle bugs that may be difficult to track, and arise even days, weeks or months after a successful deployment. It's not that the solution doesn't work - it works. Today. How to calculate the difference between today and today's date? Which time interval to use for calculating the date difference depends on the letter you enter in the last argument: =DATEDIF(A2,...
Easy tips

How do you replace a blower motor on a Dodge Dakota?

How do you replace a blower motor on a Dodge Dakota? Replacement of the blower motor takes about 30 minutes. Purchase your new blower motor at an auto parts store or your Dodge dealership. Pull the hood release lever on your Dodge Dakota and then use your ratchet set to take off the negative battery cable. Open your Dakota's glove compartment and take out all the objects inside it. Why does my Dodge Dakota blower keep going bad? If you leave the blower motor switched continually on you may not notice this. If so I suspect that there is an...
Other

What should I do if my fuel pump wont start?

What should I do if my fuel pump wont start? Turn the key to RUN, not start. Listen for the fuel pump to start and run for approximately 2-secs. Then turn the key to OFF and then back to RUN. The fuel pump should start and run a second time for approximately 2-secs. Repeat the procedure one more time. Each time the pump runs for 2-secs., it’s priming the fuel rail and building pressure. Why does my fuel pump not prime with the key on? Fuel pump doesn't prime with key on. I've been trying to figure this out for...
Most popular

Can you check brake fluid with car running?

Can you check brake fluid with car running? Before you get started you may want to know if it's best to check your brake fluid levels when your car is cold or when it's hot from running. Park your car on a level surface and wait till the engine has cooled down before popping the hood and taking a look. Can you use brake fluid as a substitute for transmission fluid? The most commonly used power steering fluid substitute is automatic transmission fluid (ATF). absolutely no substitute for brake fluid, and you should use DOT4 (research if you want to...
Common questions

What happens when your transmission is leaking?

What happens when your transmission is leaking? While it may not be especially dangerous to drive a vehicle that is leaking transmission fluid, it is not a good idea because the vehicle may not run properly. A car leaking transmission fluid can be caused by a leak in the pan. This can happen through wear and tear over time. What causes a fluid leak in a transmission? Most automatic transmissions have a pan that acts as a reservoir for fluid. A gasket provides a seal between the pan and the transmission. That gasket can eventually wear out, resulting in a...
Easy lifehacks

Do disc brakes slow you down?

Do disc brakes slow you down? Pros of disc brakes Better braking power - Disc brakes generate far more braking power than standard rim brakes. For the rider this means having to apply far less pressure on the brake levers, reducing muscle tiredness, especially on long descents where you are constantly having to check your speed. How often should you replace your brake rotors? Our recommendation: It is a good idea to get the thickness of brake rotors measured annually. Your mechanic should measure the rotor thickness every time the brake pads are replaced. Brake rotors usually last twice as...
Most popular

How much weight can a 2004 Dodge hold?

How much weight can a 2004 Dodge hold? Weight InformationOption Weight - Rear0.00 lbsMaximum Payload Capacity1834.00 lbsAs Spec'd Curb Weight4516.00 lbsTotal Option Weight0.00 lbsCurb Weight4516.00 lbs How big is a 2004 Dodge Ram truck? Dodge/Ram Truck note: The 2004 Dodge Ram 1500 is a full-size, 1/2-ton pickup truck that is available in four-door and two-door trims, and a choice between a 6.3ft or 8.0ft bed. What kind of truck is a 2004 Dodge Durango? A pickup truck that straddles the line between compact and mid-size, the 2004 Dodge Dakota is available with a 260 hp V8 making it one of...
Easy lifehacks

What causes a camshaft to fail on a roller wheel?

What causes a camshaft to fail on a roller wheel? This high spring pressure causes the heat created at the cam to be transferred to the roller wheel, resulting in its early failure. Any springs that may be used must be assembled to the manufacturer’s recommended height. Never install springs without verifying the correct assembled height and pressures. What happens when the cam lobe and lifter fail? During this break-in time, verify that the pushrods are rotating, as this will show that the lifters are also rotating. If the lifters don’t rotate, the cam lobe and lifter will fail. Sometimes...