Other

What is the length of a Ford C6 transmission?

What is the length of a Ford C6 transmission? 20" The C6 is a Ford heavy duty 3 speed automatic. The gear ratio is also identical to the C4 transmission. The C6 has a case length of 20", which includes the bellhousing. This transmission was used up to all three Ford block bolt patterns. Can a Ford 5.4 diesel be converted to 6.8? FORD STANDARD TRANSMISSIONS. Ford 5-Speed – Diesel Conversions ® currently does not make a 5.4 or 6.8 5-speed adapter plate due to the small clutch that would have to be used. We may someday for 4BT conversions....
Most popular

What is the lock on my f150 bumper?

What is the lock on my f150 bumper? It actually is a lock. You insert your key and turn it to remove a plug that fills the access hole. Then you insert the jack handle at an angle towards the center line of the truck to reach the lowering crank. Does a 1998 f150 have ABS brakes? Re: Does my 1998 F-150 XLT Have ABS Brakes Once the brake assembly is removed the spindle Nut is removed along with the outer bearing. They are no where near the same. if you have 4wd ask for front Discs. If you have...
Most popular

What is a B6 Ford axle?

What is a B6 Ford axle? The Ford F-150 comes with many different rear axle options that have different gear ratios depending on what You need to do with the truck. Some gear ratios are better at towing and others are better at on road or off road driving. If You have a code B6 on Your rear axle then that means that You have a 3.73 gear ratio. What causes the rear end of a Ford F150 to vibrate? It seems to be pinpoint approx. 50-55mph. and minimal at lower speeds. Also seems to get worse with turns and...
Other

Where is the winter front on a Ford truck?

Where is the winter front on a Ford truck? The winter front is placed in front of your pickup’s grille. There it can decrease the flow of cold air through the radiator, thus protecting it and the grille from ice and snow. Do you need a winter front on a Ford F-350? Heavy-duty cooling is good for the engine in summer, but might become a problem in winter. When the temperature outside goes down, you can end up with increased warm up time as well inability to reach proper operating temperature. To avoid all these problems, you need a winter...
Common questions

Why do car headlights dim when you start the engine?

Why do car headlights dim when you start the engine? Headlights dim when engine is turned on because the starting system uses a lot of power from the battery. As soon as the engine starts then normal beam resumes. Starting a car puts a high load on the battery, so other high drain items like headlights dim. What should you do if your headlights dim while driving? You are driving to a gas station when your headlights start to dim. Your headlights are not completely broken, but they do tend to fluctuate in brightness. Even if the dimming is temporary...
Most popular

Where is the throttle position sensor located on a 2005 Ford 500?

Where is the throttle position sensor located on a 2005 Ford 500? 2005 ford: throttle position sensor located Customer Question where is the throttle position... where is the throttle position sensor located on a 2005 ford 500? or is it called something else? Submitted:11 years ago. Category: Ford Show More Show Less Ask Your Own Ford Question Share this conversation Answered in 13 minutes by: . How do you replace the throttle position sensor? Make sure to remove the TPS sensor and 2 screws that connect to bottom of throttle body. Once the old sensor is off, replace it with...
Other

Where are the screws on a wardrobe door to adjust?

Where are the screws on a wardrobe door to adjust? This screw is located in the middle of the hinge on the cabinet side, where there are two screws next to each other horizontally. The screw you need to adjust is furthest from the door. Loosen the screw on each door hinge (top and bottom) and manually push or pull the door into the correct position. What should gap be between door and frame? Ideally, there should be a gap of 1 mm (0.039 in) between the door and frame on most cabinets. After retightening the screws, you can test...
Most popular

Where to get a Ford Ranger lowering kit?

Where to get a Ford Ranger lowering kit? Andy's Auto Sport is the ultimate shopping destination for your Ford Ranger lowering kit needs! All available coupons will be applied automatically in your shopping cart! At Andy's Auto Sport, we have a huge variety of Ford Ranger lowering kits to ensure that you have every lowering kit option available to you. How do I read Trouble Codes on a 1993 Ford Ranger? Look at the Ranger's check engine light. It will blink multiple times and then stop. The light will flicker to give a warning that the test is beginning. A...
Other

How do you change wheel bearing on Ford F-250?

How do you change wheel bearing on Ford F-250? Clean and lube the needle bearing and replace the yellow o-ring on the wheel bearing and hub assembly. Install the assembly onto the knuckle and torque the four bolts to manufacturer's specs. Grease the outer thrust washers and install followed by the snap ring. Replace the o-ring on the outer hub and install the hub. How do you change the ball joint on a Ford F 250? Remove the cotter pin and nut that attach the tie rod end to the knuckle. Remove the outer hub by squeezing the retaining ring....
Other

How do you lubricate power steering?

How do you lubricate power steering? How to Lubricate the Steering System - Vol. 260Tilt the rack by raising the car on an axle stand on one side. Clean the area around the gaiter.Place a drip tray under the rack.Free one end of the lower gaiter. Pull the gaiter free from the rack.Drain the oil in the drip tray. Is there a problem with Ford F150 power steering? Ford F150 power steering problem SOLVED! - YouTube If playback doesn't begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: xfIcCcKxERPAMg1s) Videos you watch may be...