Easy tips

Why do CV boots need to be replaced?

Why do CV boots need to be replaced? The Constant Velocity (CV) boots cover the CV joints and protect them from outside debris. They also keep the grease inside the joints for lubrication. Usually, when CV joints are damaged, you will hear a “clicking” or “knocking” sound when making turns. This is a sign that the whole CV axle needs to be replaced. How do you install a new CV boot? Step 2: Install the new boot. CV boots come with pre-cut grooves that you just need to open and install the boot over the axle area. Once it is...
Easy lifehacks

Is oil leak hard to fix?

Is oil leak hard to fix? Fixing the Problem with Tools Fixing an oil pan leak and other situations with tools is not as hard as you would think. Over time, these bolts can loosen, and loose bolts leak. After tightening all the bolts on the oil pan, move over to the timing belt cover and the valve covers. What should I do if I have an oil leak in my front transmission? A leaking front transmission seal will generally fling fluid around inside the bellhousing where a leaking engine rear main or oil pan seal may just drip to...
Easy lifehacks

Why is my trailer blinker not working?

Why is my trailer blinker not working? Turn Signals on Trailer Not Working When Running Lights are On The most likely cause for the turn signals not to work when the running lights are on with your trailer is a bad or weak ground. It's very possible that a weak ground connection can be just strong enough to allow sufficient current for some… Are there any lights that work on a Ford F-150? checked fuses seem ok, stop and turn work on trailer but it has no ruinnung lights that work, if dis connect from truck and use a batt,...
Easy lifehacks

Can I reuse lm7 head bolts?

Can I reuse lm7 head bolts? Bolts are designed to stretch as you torque them into place, and when you remove them, they snap back to their original position. Because of this, many standard head bolts are okay to use more than once, as long as they have not been stretched past their spring back point. How much torque does a Ford head have? Tighten the head's shorter bolts to between 15 and 32 ft-lb of torque. Tighten the longer bolts to between 30 and 36 ft-lb of torque. How many jack screws are in a Ford 4.6L? Modular OHC...
Common questions

Where are the air filters in climate controlled seats?

Where are the air filters in climate controlled seats? The climate controlled seat system includes air filters that must be replaced periodically. Refer to Scheduled maintenance information. There is a filter located under each front seat. The filter can be accessed from the 2nd row foot-well area. Move the front seats all the way to the full front and full up positions to ease access. Why are the heated seats not working on my Ford Expedition? Recently replaced the battery and noticed both driver and passenger seat heat and cool function no longer works. I've read on here that people...
Easy tips

Why did Ford stop making the Taurus?

Why did Ford stop making the Taurus? On April 25, 2018, Ford announced plans to discontinue the Taurus (along with the Fiesta, Focus, and Fusion), in order to focus more on its line of trucks and SUVs. The announcement was part of a plan by Ford Motor Company to cut costs and increase profits. When was the last year the Ford Taurus was made? Ford Taurus. It was discontinued in 2006, with production initially ending on October 27, 2006, and 2007 being the last model year. Ford had decided to replace the Taurus with the fullsize Five Hundred and midsize...
Most popular

What kind of wiring harness does a caterpillar use?

What kind of wiring harness does a caterpillar use? (USED)2005 CATERPILLAR C11 ACERT (KCA 70-PIN) ENGINE TO ECM WIRING HARNESS,STOCK# SC2357.For more information contact us directly. (USED) 2003 CATERPILLAR C15 DIESEL ENGINE TO 2003 FREIGHTLINER TRUCK WIRING HARNESS, STOCK# SC1872.For more information contact us directly. Where is the ECU located on an Allison Transmission? Vehicle Interface Module. This module located under the dash is the main interface between the engine and transmission controls. It houses the relays for the neutral start, high idle and exhaust brake systems. The Transmission ECU sends a signal when it's in neutral so the engine...
Most popular

What makes heat in a car?

What makes heat in a car? A car's cabin will heat up as the engine's coolant heats up. The coolant absorbs the heat from the engine, causing it to become hot. This coolant is then routed through a “mini” radiator called a heater core. This heater core then passes the hot air it generates into the vehicle with a blower fan. Do vehicles produce heat? An engine generates so much heat from combustion and friction that if it isn't continuously cooled, it can suffer serious damage. When you turn on the fan, a blower motor sends the air warmed by...
Common questions

Does a 2006 F150 Lariat have a cabin filter?

Does a 2006 F150 Lariat have a cabin filter? The 2006 F-150 does come with a cabin air filter. Where is the cabin air filter located in a 2008 Ford F150? Cabin air filter on Ford F150 is located inside the car on the passenger side. Does my 2008 Ford F150 have a cabin air filter? The 2008 ford f150 does not have a cabin air filter. Where is the cabin filter located on a 2005 Ford F150? Is there an air filter in a Ford F-150? In recent years, cabin air filters have been installed in many vehicles to...
Easy tips

What is a good ring gap?

What is a good ring gap? For a street engine, multiplying your bore size by 0.004in will give you the top ring gap you are looking for. For high performance engines, the multiplier changes to add more clearance, but the math stays the same: Modified or Nitrous Oxide - 0.005in x 4.00in bore = 0.020 inch ring gap. High Performance Racing - . Are piston rings pre-gapped? Piston rings are available both ways , pre-gapped and not , but regardless , piston rings gap should AWAYS be checked for correct end gap clearance to specs and there correct location position...