Easy tips

Where is the fuel filter located on a 2001 Dodge Durango?

Where is the fuel filter located on a 2001 Dodge Durango? The 2001 Dodge Durango 5 9 fuel filter location is inside the fuel tank. Having the fuel burn efficiently is the key to maximizing Your miles per gallon. Your gas tank needs to be in the beSTShape. You will come into problems at some point. Does a 2000 Dodge Durango have an inline fuel filter? there is no serviceable fuel filter. It is part of the fuel pump assembly and serviced when you change the pump. Does a 2006 Dodge Durango have a fuel filter? The fuel filter for...
Other

How do you reset the tire pressure light on a 2011 Dodge Grand Caravan?

How do you reset the tire pressure light on a 2011 Dodge Grand Caravan? With the ignition off, turn the key to the “On” position, without starting the car. Press the TPMS reset button, hold it down until the tire pressure light blinks three times, and then release it. Start the car, and let the engine run for 20 minutes to reset the sensor. Where is the TPMS reset button on a Dodge Grand Caravan? You'll usually find the tire pressure monitor reset button beneath the steering wheel. Where is the TPMS reset button on a 2010 Dodge Caravan? If...
Easy tips

How to disabling seat belt Ding in Dodge truck?

How to disabling seat belt Ding in Dodge truck? Turn the ignition switch to the OFF position and buckle the driver’s seat belt. 2. Start the engine and wait for the Seat Belt Warning Light to turn off. 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. How to disable the seat belt chime in a Dodge Ram? Buckle your seat belt. Turn the ignition key to the "On" position. The seat belt reminder light...
Common questions

What kind of warranty does a Dodge Grand Caravan have?

What kind of warranty does a Dodge Grand Caravan have? WARRANTIES:†2019 Chrysler, Jeep, Dodge and Ram vehicles are backed by a 5-year or 100,000-kilometre fully transferable Powertrain Limited Warranty* with $0 deductible plus 24-hour roadside assistance. How long is the warranty on a Dodge Ram truck? The Basic LimitedWarranty lasts for 36 months from the date it begins or for 36,000 miles on the odometer, whichever occurs first. How long is the limited warranty on a jeep? F. When It Ends The Basic LimitedWarranty lasts for 36 months from the date it begins or for 36,000 miles on the odometer,...
Most popular

How do you remove dashboard from Ford Thunderbird?

How do you remove dashboard from Ford Thunderbird? These photos follow the steps outlined in the shop manual. The first step is disconnecting the battery. I sometimes skip this, but with this project there will be a lot of bare wires flopping around, so I pulled the negative terminal. After that, remove the seats, including the bottom part of the rear seats. How do you replace a dash light on a Ford Explorer? Place the new light inside and twist to lock it. Repeat this for all dash lights that you are replacing. Place the instrument panel back into the...
Easy lifehacks

What happens when the air conditioner clutch does not engage?

What happens when the air conditioner clutch does not engage? When power energizes the clutch coil, the magnetic field pulls the clutch in to engage the compressor shaft. If the clutch doesn’t engage, the air conditioning compressor can’t pump refrigerant. How to troubleshoot a clutch that won't fully disengage? Step 1: Collect all tools and your creeper and place them out of the way. Step 2: Raise the vehicle. Using a floor jack that is recommended for the weight of the vehicle, lift under the vehicle at its specified jacking points until the wheels are completely off the ground. Step...
Common questions

Why do I have to push my clutch all the way down?

Why do I have to push my clutch all the way down? Broken Clutch Cable: The most common reason to have a clutch pedal that goes all the way to the floor is a broken clutch cable. Low Fluid: If you have a hydraulic clutch, there are a couple of other things it could be. One is low fluid in the master/slave cylinder. What happens when you push the clutch pedal? When you push the clutch pedal, brake fluid flows from the clutch master cylinder to the slave cylinder, applying the pressure necessary to move (engage) the clutch and this...
Most popular

What does a transmission flywheel do?

What does a transmission flywheel do? A manual transmission uses a “flywheel” A flywheel is much thicker and heavier than a flex plate and stores energy to keep things smooth while shifting gears. It also supply's a friction surface for the clutch disc. A “flywheel” usually does not crack and fail like a flex plate. What is a flywheel and why do we need it in a vehicle? A flywheel is a metal disc that resembles a gear positioned between your clutch and the transmission. This part, along with the clutch, helps to provide power to and from the engine...
Most popular

What causes excessive clutch free play?

What causes excessive clutch free play? Loose clutch pedal A broken or incorrectly adjusted cable can result in a clutch cable with excessive slack. This will cause the pedal to have too much free play when depressed before resistance is encountered and the cable starts retracting, and will result in a clutch that does not disengage properly or all the way. What happens when you have too much play in the clutch? If, however, there is too much clearance in the clutch linkage, the car tends to creep forwards when in gear with the clutch pedal fully depressed. This is...
Easy tips

How do you Bleed the clutch on a ram?

How do you Bleed the clutch on a ram? The clutch on a Ram can be bled by removing the slave clutch cylinder from the transaxle and depressing the slave cylinder pushrod. Nonetheless, a simpler method involves plastic tubing and an assistant. Begin by pumping the clutch pedal 60 to 100 times. If the pedal still feels spongy, continue to Step 2. What to do when Clutch on Cummins starts to bleed? 2. locate master cylinder piston circlip (near where pushrod snaps into master cylinder). remove circlip. 3. using pushrod, carefully pull master cylinder piston out of master cylinder body...