Other

Can a stuck thermostat cause radiator leak?

Can a stuck thermostat cause radiator leak? Another indication may also be leaking coolant which can be caused by the thermostat not allowing coolant to flow when it is stuck in the closed position. This can eventually cause other coolant hoses to leak as well resulting in coolant often times leaking on the ground under your vehicle. What would cause a lower radiator hose to collapse? The most common cause for radiator hose collapse is a vacuum issue caused by a faulty radiator cap. Another common problem is clogging of the smaller radiator runoff hose, which leads to the coolant...
Other

How to install and setup ring spotlight Cam?

How to install and setup ring spotlight Cam? Learn how to easily setup and install your Ring Spotlight Cam Battery. Spotlight Cam Battery comes with a 1080HD camera with two-way talk, two LED spotlights, and two quick-release rechargeable battery packs that lets you charge your Cam without moving the device. Get your Spotlight Cam Battery today at http://ring.com/spotlight-cam-battery. What's the easiest way to install a dash cam? There are two options to installing a dash cam, the easiest is the 12v cigarette lighter dash cam installation, but the neatest is using a hardwire kit. Cigarette lighter installation Hardwire installation Is...
Easy tips

Is it easy to drop a gas tank?

Is it easy to drop a gas tank? Dropping a fuel tank can be difficult depending on the vehicle it is in and how much fuel is in the tank. You can make removing the fuel tank a little less daunting, if you know what you are doing and have the correct tools and equipment to do so. How to change a broken fuel pump without dropping the gas tank? TheCousinDan shows you how to change a broken fuel pump without dropping the gas tank. This time it's done by actually cutting a hole in your car (don't worry, it's...
Other

How does an exhaust manifold bolt break?

How does an exhaust manifold bolt break? Q: What causes an exhaust manifold stud/bolt to break? This expansion and stretching of the manifold bolts over numerous duty cycles eventually causes too much tension on the bolt(s), stretching them beyond capacity and causing them to fail. Can a broken exhaust manifold be drilled out? Broken exhaust manifold bolts can be the start of a daunting journey of trying to figure out the best way to remove that broken bolt. Most mechanics cringe at the thought of removing broken exhaust manifold bolts as sometimes the engine will need to be removed in...
Most popular

What causes a noisy compressor?

What causes a noisy compressor? There are a few factors that make air compressors so loud, but most of the noise can be attributed to friction. Metal hitting or sliding against metal can be loud! Typically, the more moving parts an air compressor has, the louder it will be. This is true in the motor as well. How do you know when a compressor is bad? Some of the signs of a bad A/C compressor are as follows.A Lack of Hot Air Being Released Outside. Loud or Strange Noises From the Unit. Failure of the Compressor to Turn On. Circuit...
Common questions

How do you install a defroster on a GMC Truck?

How do you install a defroster on a GMC Truck? 1. Install the mode actuator as an assembly with the actuator cam. Line up the heater/defroster valve lever with the mode actuator cam slot. Line up the A/C valve lever with the mode actuator cam. 2. Install the mode actuator mounting screws to the HVAC module. Tighten the screws to 1.6 N·m (14 lb in). 3. Where is the defrost vent on my car? It is located above the driver side gas pedal. There is one vent tube that needs to be removed or pushed off to the side. There...
Other

When did the second generation Cavalier come out?

When did the second generation Cavalier come out? The second-generation Cavalier has been a great success for Chevrolet since its introduction in the 1995 model year. To help keep the sales momentum up, Chevrolet is introducing a new Cavalier model for 1997 - the Rally Sport Coupe. What kind of engine does a Cavalier have? The Cavalier RS has some of the style of the Z24, but uses the 2.2- liter pushrod four-cylinder engine of the base Cavalier coupe to make it the entry-level sporty coupe of the Chevrolet line. If the Cavalier Z24 is the Z28 Camaro's little brother,...
Common questions

How much are 68 Camaros worth?

How much are 68 Camaros worth? Data based on 1,512 auction sales. note: The images shown are representations of the 1968 Chevrolet Camaro and not necessarily vehicles that have been bought or sold at auction....Chevrolet Models.EnginesMedian Sale327 CID | 350 HP$36,750396 CID | 325 HP$42,000350 CID | 295 HP$24,000302 CID | 290 HP How much is a Chevy LS1 engine? A complete new LS1 engine, including everything but the computer, is $4900. A complete new LS6 engine, again with everything except the computer, is $6300. How much does an LS1 crate motor cost? They also include a one year, unlimited...
Common questions

How to fix blend door actuator in Chevy Tahoe?

How to fix blend door actuator in Chevy Tahoe? WARNING- Make sure the ignition key is in the OFF position when connecting the electrical connectors to ensure the proper calibration of the control panel. 1. Engage the electrical connectors to the HVAC control assembly. 2. Install the HVAC control assembly. How do you replace a blend door on a Chevy Silverado? For those interested in replacing the driver side actuator, refer to the following instructions: The driver-side blend door is accessed by removing the IP instrumental panel. Once the panel is off, simply loosen the actuator mounting screws and disconnect...
Common questions

Are there inner and outer tie rods?

Are there inner and outer tie rods? Whether your car steering design is a rack and pinion system or a steering gear box system, both systems have inner tie rod ends and outer tie rod ends. An outer tie rod end is connected to each front wheel spindle, and an inner tie rod end is connected to the steering rack or steering gear box assembly. Where is the outer tie rod located on a corvette? Now rotate both inner and outer tie rod ends rearward to the limit of ball stud travel. This note is a bit confusing in that...