Easy lifehacks

Are blind spot sensors reliable?

Are blind spot sensors reliable? Blind spot monitoring technology uses sonar, lidar, or cameras to detect vehicles that are alongside or behind the driver's automobile, even if that approaching vehicle may not appear in a side-view mirror. In reality, many blind-spot detection systems do not reliably detect cyclists. How do I test my blind-spot monitoring system? Find the location of the indicator lights. They're usually on the side mirrors outside the cabin or inside the car, on the A-pillar next to the window. Check if you can change the warning chime's volume. Some blind-spot monitoring systems may emit loud sounds...
Easy tips

Where is the no bus sign on my car?

Where is the no bus sign on my car? If any sensor shorts out the pcm goes dead and the no bus sign shows. On the rear drivers side top of bellhousing is the location for the crank sensor. Unplug the sensor and watch your dash. Your meters will restore and the NO BUS flag will be gone. What does no bus mean on a jeep? The reply stating that the battery was just changed makes me more suspicious that this is the cause. The no bus syndrome on the jeeps. Had one in the shop a no start with...
Other

What was the Check Engine light on my 1995 Sebring?

What was the Check Engine light on my 1995 Sebring? Recently, my Check Engine light came on my 1995 Sebring (90K miles currently) and it had an extremely erratic idle with coughing, jerking & sputtering. It turned out that oil had leaked into the spark plugs. When to reset the Check Engine light of the Chrysler? It's inadvisable to reset the check engine light if the underlying problem hasn't been addressed. If you do, the light will simply come back on. Retrieve the error code and tackle the problem before attempting to reset the light. What should I do if...
Easy lifehacks

Can you skip gears when slowing down?

Can you skip gears when slowing down? Engineering Explained tackled the common practice in its latest episode and the short answer is yes, it's perfectly OK to skip gears when upshifting or downshifting. If you shift from third to fifth gear and let the clutch out at the same speed as normal, the car will jerk as it works to settle the unbalance. When do you change gears while slowing down? When to change gear whilst slowing down. Whilst slowing down it may be necessary to change down a gear else the car may lose the ability to accelerate further...
Easy lifehacks

Is there a way to power open the liftgate?

Is there a way to power open the liftgate? The power open feature can be activated by the switch on the Intelligent Key, the instrument panel switch, the glove box switch or the liftgate request switch even if the vehicle is locked. The liftgate will individually unlock and open. What to do if your liftgate motor does not run? a. Motor does not run. If it is not getting power, follow the schematic through wiring to check for power to the switch to find either the faulty wire that may be broken or a faulty switch. Usually if this is...
Other

Why is my 4WD light on Jeep Patriot?

Why is my 4WD light on Jeep Patriot? If the 4WD warning light stays on constantly after you start the Jeep, you most likely will need to have the 4WD system itself at by a mechanic. It may be safe to drive, but the 4WD system is probably disabled If it's a FULL TIME 4WD, it may NOT be safe to drive at ALL. How does the 4x4 work on a Jeep Patriot? This system is a full-time front-wheel-drive based 4WD/AWD system that is front-wheel-drive when it has traction, but can automatically put up to 50% power to the rear...
Easy lifehacks

What happens when your timing belt goes bad?

What happens when your timing belt goes bad? As the chain stretches, however, performance will be affected. Also, on many vehicles the camshaft sprocket is made of plastic. When these vehicles are overheated even slightly this plastic can melt and the chain will skip teeth. The engine will stop immediately and will not run again until the chain is repaired. How to check valve timing with timing belt? To check valve timing remove the valve cover so you can see the valves for number one cylinder. (This method can be used to align the cam (s) for belt or chain...
Other

What is a SKIM Code?

What is a SKIM Code? What are SKIMs? A SKIM key is a programmed key that carries a unique code for each vehicle. It cannot be used to start any other car. If somebody uses a key carrying the same pattern as your car key to start your car, it will not work. Where can I get my Chrysler 300 pin #? Locksmiths can get the PIN # via TechAuthority for $20 (if they're a member of the Associated Locksmiths of America. I programmed the third key (with the car) which I will have on my wallet just in case...
Other

Do AC condensers come pre charged?

Do AC condensers come pre charged? Yes. All of the air conditioning systems we offer are pre-charged to allow for the volume of about 20 feet of refrigerant lines. Why is my AC condenser not running? In general, this problem is caused either by a dirty condenser and fan or a clogged condenser. The condenser unit won't turn on: If your condenser unit won't turn on at all, you may have a faulty motor or the unit may not be receiving power. Examine all wiring and ensure that the unit is plugged in. Do new AC units need charging? The...
Common questions

Why is my Chrysler 300c overheating?

Why is my Chrysler 300c overheating? While there are a variety of reasons your Chrysler 300 is overheating, the most common 3 are a coolant leak (water pump, radiator, hose etc.), the radiator fan, or a failed thermostat. When does a car engine overheat what causes it? An engine will overheat any time the cooling system is malfunctioning (i.e., when the coolant doesn’t absorb, transport, and dissipate heat effectively). Diagnosing the reason why your cooling system is on the fritz is more complex, but there are several common culprits of an overheating engine: What happens when your computer overheats and...