Easy lifehacks

What are the problems with a 2008 Nissan Pathfinder?

What are the problems with a 2008 Nissan Pathfinder? Worst 2008 Nissan Pathfinder Problems #1: Cracked Radiator & Transmission Failure 2008 Pathfinder Average Cost to Fix: $3,900 #2: Premature Timing Chain Shoe Wear 2008 Pathfinder Average Cost to Fix: $1,200 #3: Vibration 2008 Pathfinder Average Cost to Fix: $4,900 What to do if your Nissan Pathfinder won't start? It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes. It is highly likely that if your Pathfinder won’t start that there will be codes. These codes will tell you...
Easy lifehacks

What causes a p0017 on a Ford Explorer?

What causes a p0017 on a Ford Explorer? P0017 in the Ford Explorer is predominantly caused by a few different things. It is typically thrown when the Crankshaft Position Sensor and the Camshaft Position Sensor are out of alignment by a certain number of degrees, or if there is an issue with the wiring, or one of the sensors themselves may have gone bad. What causes a crankshaft to be in p0017 position? To sum things up, the common causes for code P0017 are as follows: 1 A faulty cam or crank sensor 2 The cam or crank circuit is...
Common questions

What does code P040D mean?

What does code P040D mean? Exhaust Gas Recirculation Temperature Sensor OBD-II Code P040D is defined as a Exhaust Gas Recirculation Temperature Sensor "A" Circuit High. An Exhaust Gas Recirculation (EGR) Temperature Sensor is an electrical sensing probe that monitors EGR temperature going in and out of the EGR Cooler and transmits the signal to the engine control control module. What causes an engine to have a p040d code? Causes for this P040D engine code may include: Defective or damaged EGR (Exhaust Gas Recirculation) temperature sensor. EGR temperature sensor gasket leaking. Cracked or leaking exhaust pipe in which the sensor is...
Most popular

What are the different types of fuel pumps?

What are the different types of fuel pumps? Types of Fuel PumpsMechanical Fuel Pump: ( Types of Fuel Pumps ) Mechanical Fuel Pump. Electric Fuel Pump: ( Types of Fuel Pumps ) Electric Fuel Pump. High Pressure Fuel Pump: ( Types of Fuel Pumps ) High Pressure Fuel Pump. What's the difference between a mechanical and electrical fuel pump? Mechanical fuel pumps use a type of vacuum to deliver the fuel to the engine. If you drive a specialty car or a carbureted vehicle, you will find that it has a mechanical fuel pump. Electrical Fuel Pumps – It has...
Easy tips

Why does my car stall when I back up?

Why does my car stall when I back up? Hi there. Usually when you shift into reverse and engage the brake it will cause the engine RPM to drop; as it's creating a load against the transmission and the engine. If the engine stalls, it may be caused by a faulty idle control valve, bad O2 sensors, or clogged fuel injectors. What causes a car to stall when put in gear? The EGR valve, alternator, or fuel pump gets faulty. The battery has died. An air filter gets dirty. The fuel pressure is low. This case likely occurs in case...
Most popular

Where does the ambient air temperature sensor connect?

Where does the ambient air temperature sensor connect? The ambient air temperature sensor connector attaches the sensor to the wiring needed to connect to the control unit for the heating, ventilation, and air conditioning (HVAC) system to keep from putting additional stress on the system in especially hot or cold climates. The connector also attaches the sensor to the ECU to display... What is the resistance of the ambient temperature sensor? Turn the ignition switch to the Off position. Disconnect the ambient temperature sensor wire harness connector. Measure the resistance of the ambient temperature sensor. At –40° C (–40° F),...
Most popular

How does the universal joint work on a Ford Ranger?

How does the universal joint work on a Ford Ranger? The universal joint (also known as a U-joint) on a Ford Ranger pickup connects the drive shaft to the rear axle. Power generated by the engine travels through the transmission and drive shaft. The design of the universal joint allows it to rotate while bending to compensate for different drive line angles, while the rear axle moves up and down. What's the best way to replace a universal joint? Dislodge the universal joint from the both the yoke and the driveshaft. Remove all dirt and debris from the entire drive...
Common questions

How do you bleed the brakes on a 1991 Ford f150?

How do you bleed the brakes on a 1991 Ford f150? There is a bleeder screw at each caliper/wheel cylinder. You looosen this screw (don't remove it) and have someone depress brake pedal and hold it down. Tighten bleeder screw, release brake pedal, and repeat until you get only fluid (no air) from the bleeder. Catch the fluid in something to kep it off the ground. How do you Bleed the brakes on a Ford F150? Fill the reservoir with new brake fluid (don't reuse old fluid as it holds moisture and will corrode your brake system). Start with the...
Common questions

Can too much positive caster cause death wobble?

Can too much positive caster cause death wobble? But the fact is that having too much or too little caster can cause problems for your Jeep's steering. Adding lift to a Jeep's suspension can throw off your factory caster angle. If your Jeep has too little caster angle, it can be a candidate for developing death wobble. As always, too much of a good thing ain't bad. What does death wobble mean on a Ford F-350? With no satisfactory answers from Ford or Ford dealerships, this engineer explains what’s happening during a death wobble. A recent video posted on Reddit...
Easy lifehacks

Where is the shifter bushing located?

Where is the shifter bushing located? The rear of the shifter support frame connects to the chassis with a bushing inserted into a bracket. The bushing has slits in it to hold it in place on the chassis bracket. Pry it out one side at a time with a screwdriver. Once you get the chassis bushing off, the shifter drops out. Why are some of the tiles on my floor shifting? This can allow moisture to penetrate the floor and cause mold, mildew or other damage to occur. If only a few tiles are shifting, it is more than likely...