Easy tips

What causes a car to hesitate when shifting gears?

What causes a car to hesitate when shifting gears? If topping up the fluid doesn’t help, the fluid could be dirty, or there could be worn parts in the transmission – usually the bearings, reverse idler gear, or gear teeth. Hesitation: If the car hesitates when shifting, it’s usually a problem with the clutch. Why does my car shake when I put the car in neutral? As it worsens, you’ll notice shaking. Again, get it checked. Noise in neutral: If you notice a bumping sound when your car is in neutral, the problem could be as simple as low or...
Easy lifehacks

How does the air bag clockspring work on a car?

How does the air bag clockspring work on a car? The air bag clockspring connects the electronic controls in the steering wheel to their systems. This can include the air bag itself, radio controls, cruise control, and the horn. The air bag clockspring allows the controls to be connected while the steering wheel is able to rotate. What is the name of the engine control module? The engine control module (ECM), also commonly referred to as the engine control unit (ECU) or powertrain control module (PCM), is one of the most important components found on virtually all modern vehicles. How...
Easy tips

What does service StabiliTrak mean on a Chevy?

What does service StabiliTrak mean on a Chevy? Service StabiliTrak Chevy This system responds to oversteer or understeer conditions, improving safety for drivers less experienced in driving on slippery surfaces such as snow or ice. Chevy's StabiliTrak system can detect when the driver needs assistance and then apply the brakes or adjust power for a smoother ride. What does reduced engine power, service Stabilitrak, traction control? Reduced engine power, service stabilitrak, service traction control. Reduced engine power, stabilitrak service, and traction control service showed up on my informations center. Cleaned the throttle body, checked throttle body wiring harness and other...
Easy tips

When do I hit the gas my car jerks?

When do I hit the gas my car jerks? My car jerks slightly when I'm at a steady speed or tryin... when I try to stay at 40 45 mph my car chugs jerks slightly, but when I hit the gas it goes away only usually at those speeds. I replaced spark plugs all but number 3 today didn't change anything, change tps nothin, changed air tempature sensor and no change. Why does my car jerk at low speeds? Car jerks when accelerating at low speeds is not something rare. If you have driven a stick shift car before or...
Other

What kind of rear end does a Chevy truck have?

What kind of rear end does a Chevy truck have? If you have a 3/4 ton or larger truck, that's a different animal. On the 1/2 ton with the stock 4.11 rear end and 6.00-16 tires, at 50 mph, your engine is running at 2500 rpm, which is easily in the safe range for the 216 engine, if it's in good condition. How big is the rear end of a Chevy Camaro? It has the 4.75″ bolt pattern, and ratios are usually 3.55-3.73, but sometimes you’ll find a 3.36. The 78-88 mid size GM cars use a 7.5″ 10 bolt,...
Other

Why does my Silverado turn off the fuel pump?

Why does my Silverado turn off the fuel pump? So, my suspicions about the fuel pump were wrong! The found a stored P1626 code, which means there was a communication problem between the Theft Deterrent Module and the PCM. When it doesn't receive the right password, it disables the fuel pump. What should I do if my Silverado engine dies? Update as of today: 1) the truck hasn't started and kept running since last week. It only starts right up, then dies immediately. 2) I got a fuel pressure tester and the pressure is at 53 with key on, and...
Most popular

Where is the EVAP canister located on a car?

Where is the EVAP canister located on a car? Step 3: Locate the EVAP canister. On most domestic and foreign vehicles sold in the US, the EVAP emissions canister is located next to the fuel cell. It is shaped in a rectangular or spherical design and has three vapor lines attached to it. One line attaches to the fuel cell, one to the EVAP purge solenoid and one to the EVAP vent solenoid. When to replace an evaporative emission control canister? When the EVAP emissions canister fails it triggers an OBD-II error code (0499) collected by the vehicle's ECM and...
Common questions

Why does my car make a gurgling noise when shifting gears?

Why does my car make a gurgling noise when shifting gears? This noise is caused by the excess air in your transmission line. Commonly, drivers will notice this gurgling noise when their transmission slips while shifting gears. If you hear a gurgling noise, particularly while shifting gears, it may mean that your fluid levels are low enough to cause damage to your transmission. Why does my car not move when I put it in gear? If your car doesn't move when you put it into gear, it may be due to a simple oversight or you may have a serious...
Common questions

How to fix driver side power door lock?

How to fix driver side power door lock? 1. disconnect the battery and connect both the positive and negative cables together(after disconnected)) 2. disconnect the window and lock controller in the driver's side door. 3. Leave cables connected for at least 5 minutes 4. Re-connect door window controller and locks wiring harness 5. Why is my power door lock not working? Power door locks and driver side power window not working. Keyless remote will not open doors although when pressed, the interior lights come on so I don't believe it is an issue with the fob battery. Other power windows...
Other

What causes a Chevy Silverado to have a p0340 code?

What causes a Chevy Silverado to have a p0340 code? Chevy Silverado P0340 Causes As stated above, the P0340 code is often caused by a failure in the Camshaft Position Sensor itself. Here are the most common causes: Wiring Issue – The Camshaft Position Sensor wiring is exposed to harsher conditions than a lot of the wiring in your Silverado. What to do if your camshaft position sensor says p0340? Visually inspect the camshaft position sensor connector in search of corroded or broken connectors. Make any other repairs (if other codes are present) to make sure that other codes are...