Most popular

Do brake pads affect ABS?

Do brake pads affect ABS? In about 90% of cases, your ABS light is not caused by worn brake pads. Your brake pads have no bearing on whether or not your ABS system will work. Remember, all the ABS does is control the pressure on your brakes. Is the wheel speed sensor part of the ABS system? The ABS wheel speed sensor can also be called an ABS brake sensor or, more plainly, an ABS sensor. Whatever it is called, it is a critical part of the ABS. The anti-lock braking system (ABS) is found on most new vehicles. What...
Common questions

Why is my reverse light switch not working?

Why is my reverse light switch not working? Bulbs all OK? Chances are your reverse light switch is faulty. Just to make sure the circuit is OK, bridge the 2 terminals on the white connector with a small piece of wire and if the lights come on, then the circuit is fine and the fault probably lies with the switch. What to do if your backup light switch is bad? For this reason, if you suspect that your vehicle’s backup light switch is having a problem, have a professional technician, such as one from YourMechanic, diagnose the vehicle’s lights to...
Most popular

Can a bad or failing orifice tube cause a car to freeze?

Can a bad or failing orifice tube cause a car to freeze? If the AC evaporator or orifice tube malfunctions, it can cause refrigerant to flow unmetered through the vehicle’s AC system. This can cause the evaporator to freeze over, or frost to form or come from the vehicle’s AC vents. What are the problems with the 2013 Chrysler 200? Worst 2013 Chrysler 200 Problems #1: Transmission Slipping 2013 200 Average Cost to Fix: $4,000 Average Mileage: 39,000 mi. Learn More #2: Problems Shifting 2013 200 Average Cost to Fix: $2,500 ... What happens if the orifice tube of an...
Most popular

Why does my car stall immediately after starting?

Why does my car stall immediately after starting? Rarely I have to rev at stops or the idle drops too low and stalls. If I punch the gas very quickly it revs and drops quickly and then stalls. Starting has a success rate of about 50% without revving. If it stalls, I must rev the engine to start. Why does my Jeep stall when I start the engine? If it starts, the fuel pump is the problem. If not, the engine should be checked for spark. It could be a sensor or computer-related problem. To be absolutely sure, raise and...
Easy tips

What is the Grateful Dead station on XM radio?

What is the Grateful Dead station on XM radio? channel 23 It airs on Sirius XM Radio channel 23 and on Dish Network channel 6023. Does Sirius have a Grateful Dead channel? On the Grateful Dead Channel, exclusively on SiriusXM, you'll hear music spanning the band's career with unreleased concert recordings, original shows hosted by band members, and even rare archival interviews with Jerry Garcia. What kind of Aux in cable do I need for SiriusXM? Your Radio with Vehicle Kit includes an Aux In Cable in the product package. If you don't have an Aux In Cable, you can...
Most popular

What are the tail lights on a PT Cruiser?

What are the tail lights on a PT Cruiser? Restore both with a tail light assembly replacement for Chrysler PT Cruiser from AutoZone. Your Cruiser tail lamp assembly houses the rear lights that are engaged when you brake, signal a turn or go into reverse. They give a clear and bright view to other drivers to promote safe driving. What causes the parking brake to fail on a PT Cruiser? Road grime can build up inside, causing the parking brake to fail. Put wheel chocks in front of and behind the front wheels of the Cruiser. Lift up the rear...
Easy lifehacks

Why does my car not start after replacing the timing belt?

Why does my car not start after replacing the timing belt? When replacing timing belt or chain or cylinder head often the fuel injectors will need to be removed or the fuel line will need to be disconnected. As a result it will take some time to build fuel pressure. Also, check all your connections. If the car has good compression, spark, and fuel it should start. What causes the ignition timing to go off? If it is pointing at another tower, then you got the cam timing off, which in turn will throw off the ignition timing. One more...
Most popular

Can a locksmith duplicate a key fob?

Can a locksmith duplicate a key fob? Going Through a Locksmith or the Manufacturer. Call a local locksmith to ask about getting a copy of your key fob made. These days, most traditional locksmiths have all the tools needed to duplicate basic unencrypted electronic key fobs. Can key fobs be cloned? 1 – Can Car Key Fobs Be Cloned? Yes, as you've seen from the technology described above, key fob cloning is possible today. It's a bigger risk than it's ever been since the devices used for car key cloning are widely available and affordable. Does Home Depot copy key...
Easy lifehacks

How old can a child be to be left alone at home in California?

How old can a child be to be left alone at home in California? In California, there is no specific law regarding the age a child may be left home alone. Factors should be taken into account, such as the maturity and emotional level of the child, and any medical or psychological issues or disabilities have to be considered. At what age is it safe for a child to be left at home without supervision? In general, it's not a good idea to leave kids younger than 10 years old home alone. Every child is different, but at that age,...
Easy lifehacks

What should be included in an attached garage firewall?

What should be included in an attached garage firewall? Attached Garage Firewall Material Seams and Penetrations. The attached garage firewall should have no missing / damaged drywall sections. Any penetration must be sealed (fire rated caulking would be perfect for small gaps around the pipes, air ducts, door frames, etc) How to configure a firewall for box applications? The apps detect and use the proxy configured for the local machine via: Windows does not support local file path schemas for the .pac file location such as file://C:\proxy.pac. Use a URL to configure the .pac file location. Or manually setting the...