Common questions

How do I add Freon to my Ram 1500?

How do I add Freon to my Ram 1500? How to add freon to your 2012 Ram 1500: hook up the can of refrigerant (likely r-134a) to the low pressure port. When your compressor kicks on, add freon to the correct pressure. In addition to cooling, freon lubricates the compressor when it runs. Why does my Ram 1500 air conditioner blow hot air? When the air conditioner in your 2012 Ram 1500 starts blowing hot air, you likely have a freon leak. Recharging the freon in your AC system is an inexpensive and easy first step to restoring the cooling...
Most popular

What are the problems with the Dodge Grand Caravan?

What are the problems with the Dodge Grand Caravan? See all problems of the 2010 Dodge Grand Caravan . Tl-the contact owns a 2009 Dodge Grand Caravan. The contact stated that while driving using cruise control, the contact depressed the brake pedal but the brakes failed. The contact depressed the brake pedal once more and the vehicle began to decelerate. How much does it cost to replace the temperature sensor on a Dodge Grand Caravan? received a Ambient Temperature Sensor (Switch) Replacement. Dodge Grand Caravan Ambient Temperature Sensor (Switch) Replacement costs $124 on average. What is the Ambient Temperature Sensor...
Common questions

How many miles can you get out of a 2013 Dodge Dart?

How many miles can you get out of a 2013 Dodge Dart? How many miles can a Dodge Dart last? We're approaching 18,000 miles and the 2013 Dodge Dart is barking for oil. We last changed it at around 10,000 miles. That's a longer interval than most purists would tolerate, but not unusual among new cars that can go up to 15,000 without an oil service (our former Jaguar XF). Is the 2013 Dodge Dart Rallye reliable? The 2013 Dodge Dart has a reliability score of two out of five from J.D. Power. What mileage do Dodge Darts start having...
Easy tips

What pressure should acetylene torches be set at?

What pressure should acetylene torches be set at? 3 to 5psi The gas pressures should be set at 3 to 5psi for Acetylene, and 20 to 30psi for the oxygen, but when you squeeze the oxygen lever after the initial flame adjustment of the preheat flames to neutral just to a point where the feather disappears,the oxygen cutting stream should be visible and at least 4 inches in length ... Why does my cutting torch keep popping? The reason that an oxyacetylene cutting torch will pop and go out is because of a problem with gas flow. Usually this is...
Easy lifehacks

Why does my Dodge Ram have a p0335 trouble code?

Why does my Dodge Ram have a p0335 trouble code? The Dodge Ram utilizes a crankshaft position sensor in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank. When the Ram’s ECM determines that there is an issue with the signal coming from this sensor, it’ll throw the P0335 trouble code. P0335 Symptoms: Dodge Ram What does a p0122 code on a throttle position sensor mean? A P0122 code means that the the vehicle's computer has detected that the TPS (throttle position sensor) "A" is reporting too low a voltage. On...
Most popular

Can CKD diagnosis be wrong?

Can CKD diagnosis be wrong? Barasch. “But because the course of creatinine cannot be known when first seeing a patient, it is possible to deliver the wrong diagnosis. An initial misdiagnosis can lead to mistreatment, with potentially dangerous consequences.” Failure to treat dehydration can quickly lead to irreversible kidney damage. What are signs of kidneys not working right? If your kidneys aren't working properly, you may notice one or more of the following signs:Fatigue (extreme tiredness)An upset stomach or vomiting.Confusion or trouble concentrating.Swelling, especially around your hands or ankles.More frequent bathroom trips.Muscle spasms (muscle cramps)Dry or itchy skin. What are...
Easy tips

What to do if your shift linkage is bad?

What to do if your shift linkage is bad? To fix it, check the shift linkage and then see if there’s poor lubrication, binding, or misaligned components. The car repair manual can help you with this procedure so that you can safely remove components before inspecting for potential problems. 7. Transmission is jumping into the neutral mode Why do some manual transmissions have bad linkage? After years of service, manual transmissions become vulnerable to certain issues. These problems are developed due to lack of maintenance practices, abuse, and high mileage. However, most of these issues can also be caused by...
Most popular

Why does the Honda HandsFreeLink keep draining the battery?

Why does the Honda HandsFreeLink keep draining the battery? The lawsuit says Honda messed up when it created the HandsFreeLink unit to stay on even when the ignition switch is turned off. This always-on status creates a constant "parasitic drain" on the electrical system and a series of dead batteries. Why is my Bluetooth module draining my battery? Assumption is a battery drain. First port of call was to check the A/C Relay but no change in the battery draw. Eventually pulled the "i backup" fuse and the reading dropped to 0.02 - Think I have found a possible source....
Most popular

Why does my clutch squeak when I press it?

Why does my clutch squeak when I press it? If you hear a high-pitched squeaking as you press the pedal then you know that you have a problem with your clutch. This sort of noise is usually associated with problems with the clutch release or throw-out bearings. Press the clutch pedal all the way down. What happens when a clutch disengages? Clutch pressure plate failure symptoms can occur when you aren't engaging the clutch. The clutch springs push the pressure plate against the clutch disc. This presses against the flywheel and locks the engine to the transmission input shaft, causing...
Common questions

Why are my lights pulsating?

Why are my lights pulsating? Flickering or blinking lights are usually caused by one of four things: Problem with the bulb (not in tight enough, wrong bulb type for dimmer switch) Faulty light or fixture switch. Appliance pulling large amounts of current on startup, causing a voltage drop. Why are my lights flickering when I turn them on? The flickering or dimming of all your lights, especially when you turn on an appliance, could indicate a more serious problem with voltage fluctuation or loose wiring. Here’s a look at some common reasons your lights can flicker. These types of lighting...