Most popular

What are the causes of a P0300 leak?

What are the causes of a P0300 leak? P0300 Causes 1 Faulty or worn spark plugs * 2 Faulty spark plug wires or coils * 3 Distributor failure * 4 Faulty fuel injector 5 Vacuum leak 6 Low fuel pressure 7 Camshaft sensor defective 8 Crankshaft sensor defective 9 Engine timing off 10 Leaking head gasket What does it mean when your car says P0300? Many times, P0300 occurs when there are worn out spark plugs, spark plug wires, or a faulty ignition coil. P0300 should be repaired immediately. Ignoring this error could result in ignition failure, catalytic converter damage,...
Common questions

Which is better a new starter or a remanufactured alternator?

Which is better a new starter or a remanufactured alternator? We discuss benefits of new vs. remanufactured units, core charges, and more. Starter motors and alternators have a tough job. Starter motors are high-torque motors which must have the ability to turn over, or crank, an engine under varying weather and mechanical conditions. What's the best way to remove and replace an alternator? Follow these simple, step-by-step instructions for removing and installing an automobile alternator with common tools. Includes advice on the correct wiring as well as testing and troubleshooting tips. Sponsored by BBB Industries - makers of premium alternators...
Most popular

What to do if your computer display is dim but still working?

What to do if your computer display is dim but still working? If the display is dim but still working, your batteries are running low on power. They will need to be replaced with new batteries by opening up the back cover and switching out the old batteries for new ones. For a more detailed explanation of the process of removing the batteries, view our guide here How do you mute a radio on a car? Turn the radio on and then turn the key to the "OFF" position. Press and hold down the "Mute" button on the radio and...
Other

Where was the Chevy Impala engine shut off without warning?

Where was the Chevy Impala engine shut off without warning? Tl the contact owns a 2012 Chevrolet Impala. While driving approximately 40 mph, the vehicle shut off without warning. The vehicle was towed to premier Nissan of metairie (504-455-5800, located at 6636 veterans memorial blvd, metairie, la 70003) to be diagnosed, but the failure could not be duplicated. What causes a Chevy Impala to throw p0014? When the camshaft timing will not return to a less aggressive profile after heavy engine load, P0014 will be thrown. P0014 affects bank 1, which is on the side of the engine where cylinder...
Easy tips

How do I correct my speedometer?

How do I correct my speedometer? Press and hold the calibration button located on the speedometer, start the vehicle, and then release the button. Press that button again and then take the test drive. Once you have driven the distance needed, press the button once more and the speedometer will calibrate itself to accommodate the new tire size. Do I need to calibrate my speedometer? Installing bigger tires improves acceleration, handling and makes your vehicle look good, but it is essential to recalibrate your speedometer to get correct vehicle speed readings. What should I do if my speedometer is wrong?...
Other

Is there no spark from distributor to spark plugs?

Is there no spark from distributor to spark plugs? Q: No spark from distributor cap to spark plugs. Car died while driving. Wouldn't start again. I did basic No start troubleshooting. Tested from the ignition coil to the distributor is good, from the cap itself no power. I replaced the cap, rotor, tfi, distributor itself, and the ignition coil. Same results. When to remove the distributor on a rotor? If yes, it should start. If no, see below. The distributor needs to be removed if the rotor doesn’t point to #1 terminal. Rotate the rotor until it does. The helical...
Easy tips

Are there any problems with the Chevrolet Traverse?

Are there any problems with the Chevrolet Traverse? For being such a big name in the realm of the automotive industry, Chevrolet certainly has some issues with their cars. The Chevrolet Traverse has a huge host of problems that have hurt the Chevrolet reputation. When did the Chevrolet Traverse start being made? Originally being marketed and branded as a full-size crossover, the Traverse began assembly in 2009. Unfortunately, the inception of the Traverse is when the problems began, and it has continued through 2018. How much does it cost to repair a Chevy Traverse? The average repair cost for this...
Easy lifehacks

When did Northway Motors become part of GM?

When did Northway Motors become part of GM? When Durant bought companies that became part of GM, Northway continued to supply engines to his former clients and added Cadillac, GMC and Oldsmobile to the list, then Northway Motors became the Northway Motor and Manufacturing Division in 1925 and became part of the GM Intercompany Parts Group. When did Chevrolet stop using the straight 6 engine? Unsourced material may be challenged and removed. The Chevrolet straight-six engine was Chevrolet's sole engine from 1929 (when it replaced their 171-cubic-inch (2.8 L) inline-four) through 1954, and was the company's base engine starting in...
Common questions

What do I need to convert my 88-98 Chevy to 4WD?

What do I need to convert my 88-98 Chevy to 4WD? Truth is if you really want to convert your 88-98 Chevy from 2WD to 4WD you need the following: 1 Front SAS (Solid Axle Swap) 2 Transfer case 3 Front Driveshaft 4 Swap kit Can a Chevy truck be converted to 4WD? The good news is that parts from Chevy trucks between 01-07c all use the same parts. Bonus! Your parts availability should be easier. All the front suspension, transmission cross-member, and torsion bar cross-member parts are the same. You will need some diff mounts. You can have a...
Easy tips

What can I use to seal a transmission pan?

What can I use to seal a transmission pan? Number 2 sealants work best on cork gaskets or paper oil pan gaskets. They are often used on neoprene transmission pan gaskets as well. Aviation form-a-gasket has the advantage of being brushable, so you can lay on a thin or thick coat to seal metal flanges, machined surfaces and solid gaskets. When to put new seal on transmission pan? Many mechanics will use a scraped along the surfaces to make sure any debris is knocked off before adding a new seal and sealer. Also, allow the pan sealer you are using...