Most popular

How do you start a 2002 Ford F-150 without the key?

How do you start a 2002 Ford F-150 without the key? The easiest way to start a Ford F-150 without a key is to use a flat-head screwdriver as leverage. You simply put the flat head of the screwdriver into the ignition and turn it as you would your normal key. Is there a replacement key for my Ford F-150? For Ford F-150 vehicles that are older than ten years, there are no codes available. So, an automotive locksmith is your only option to get a replacement key. For Ford F-150 vehicles equipped with a transponder system and/or remote, intelligent...
Common questions

When to replace your AC blower motor resistor?

When to replace your AC blower motor resistor? Replaces Part# - 89019088, 973-405, 15-81086, 22807123 on various vehicles from model years including 2003, 2004, 2005, 2006 and 03, 04, 05, 06 with manual AC controls and without rear A/C vents in the center console OEM Fit, Quality, Finish - A direct replacement for your your factory HVAC Fan Blower Motor Resistor. Where is the AC blower motor resistor harness located? If you can no longer adjust the air speed with your AC controls or your AC system no longer blows chances are you need a new Blower Motor Resistor. This...
Easy lifehacks

Why does my car squeal when I hit 60 mph?

Why does my car squeal when I hit 60 mph? The squealing happens at around 40-60 mph, regardless of whether I'm on the brakes or not. The calipers, rotors, and the wheel itself are extremely hot. It also has a very bitter burning smell. How would I be able to isolate this problem? The parking brake may not be releasing on that wheel. The parking brake cable may be damaged or rusted. What's the squealing sound when you hit the brakes? It's an extremely high pitched and loud squeal... hurts the ears. After the trip, I felt the alloy wheel...
Other

When do you get a TBC fault message?

When do you get a TBC fault message? Vocational, Technical or Tra... 2006 F350 - TBC Fault shows up often upon starting and sporatically when driving with or without towing a trailer. Trailer brakes will work for a short time some of the time, until the fault message a … read more What does TBC fault mean in a truck? The TBC (trailer break Modual) controls the trialer brakes . When the light comes on, it means you have system fault in teh system. Will driving without a trailer cause any damadge to anything? No you are ok to drive...
Easy lifehacks

What are the signs of a bad alternator or battery?

What are the signs of a bad alternator or battery? Signs of a Bad Alternator or Battery Your stomach sinks as you put in your key, only to have your car not turn on. If your car won’t start, it’s often due to a malfunction of either the battery or the alternator. If it’s one of those two, placing the blame can be relatively simple. How does an alternator and battery work together? Anything less than that and your car isn't even able to start. Both of these car parts control your electrical system. However, your alternator charges your battery...
Most popular

What size engine comes in a 2005 Ford Focus?

What size engine comes in a 2005 Ford Focus? 2.0 liters ZX4 SES 4dr Sedan 2005 Ford Focus SpecsPerformanceBase engine size2.0 litersBase engine typeI-4Horsepower136 hpHorsepower rpm6,000 What kind of engine does a Ford Focus have? Four body styles are offered: the ZX3, a three-door hatchback; the ZX4, a four-door sedan; the ZX5, a five-door hatchback; and the ZXW, a wagon. Three engines are offered. All models but the ZX4 ST come with either the 130- or 136-horsepower 2.0-liter four-cylinder. Is the Ford Focus ZX4 St a good car? We found the sporty ZX4 ST fun to drive, if a bit...
Other

What happens when battery gets old?

What happens when battery gets old? And batteries degrade even if you don't use them. According to battery-testing firm Cadex Electronics, a fully charged lithium-ion battery will lose about 20 percent of its capacity after a year of typical storage. But even ideal storage conditions can leave you with a dead battery after three or four years. Are old lithium ion batteries dangerous? Lithium batteries are everywhere, and they're more dangerous than you think. Here's what to know. Lithium batteries have caused a number of fires and explosions in consumer products and at recycling plants in the U.S. Consumers should...
Common questions

What is considered 1st 2nd and 3rd shift?

What is considered 1st 2nd and 3rd shift? 1st shift usually takes place between the hours of 9 a.m. and 5 p.m. 2nd shift is worked between 5 p.m. and 1 a.m. 3rd shift typically takes place between the hours of 12 a.m. and 8 a.m. What are 1st shift hours? First shift (Day shift): The first shift typically runs from around 8:30 a.m. to 5:30 p.m. or 9 a.m. to 6 p.m during traditional business hours with one hour for lunch. Generally, it starts in the morning and ends in the afternoon. What time is third shift usually? The...
Most popular

How do you program a key fob for a 2015 Ford Fusion?

How do you program a key fob for a 2015 Ford Fusion? Step-by-Step Ford Key Fob Programming InstructionsClose the car doors, then open the driver-side door. Press the UNLOCK button on the driver-side door.Next, turn the ignition from OFF to RUN 8 times. Press any button on the Ford remote to be programmed. Have a second remote key fob? Finally, turn the ignition to OFF. What is the remote keyless entry system on a Ford Fusion? Ford Fusion is equipped with Keyless Entry System. This feature usually consists of Remote Keyless Entry (RKE) as well as Remote Keyless Ignition (RKI)....
Easy lifehacks

What to do if your timing is incorrect?

What to do if your timing is incorrect? If timing is incorrect you could have a hard start, fault codes or a no start condition. Begin by preparing the vehicle. Place transmission in Neutral. Raise and support the front of the vehicle safely. Remove the right front wheel well liner. What's the best way to remove a timing chain? Put the bolt partially back in the bolt hole and use a harmonic balancer removal tool. The tool should not be a jaw type tool, but instead should apply all of the removal force to the center of the assembly. This...