Common questions

How to install distributor gear on a Ford truck?

How to install distributor gear on a Ford truck? INSTALLATION INSTRUCTIONS: STEP 1:Remove roll pin from distributor gear and shaft. Save pin for re-assembly. STEP 2:Verify that the shaft endplay is .024" to .035". Modify collar if necessary. Some aftermarket distributors may be constructed in a manner that does not allow you to achieve .024" to .035" of endplay. How does a 2.3 turbo work on a Ford Ranger? The 2.3 Turbo cars use low impedance injectors. After you have all this installed you're about ready. You need to have a pipe fabbed up to run between the mass air...
Other

Where is fuse box 2011 f150?

Where is fuse box 2011 f150? The fuse panel is located under the right-hand side of the instrument panel. To remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it. To reinstall it, line up the tabs with the grooves on the panel, then push it shut. Where are the relay boxes on a Ford F150? Relay box 1 Ford F150 1999-2003. Relay box 1 is located behind left side of instrument panel. identifying relay box 1. Relay box 2 Ford F150 1999-2003. Relay...
Other

What does a blinking anti theft light mean?

What does a blinking anti theft light mean? Your car has a built-in anti-theft system. The Anti-theft Light in the dash of your car should flash periodically to show that the system is engaged and active. Tip. You have to lock the doors of the car (without it running) for the alarm to engage. Where is the anti theft light on a Ford? The display of the car behind the steering will light up and will show the anti-theft light blinking or constantly lit. Leave the key in this position for at least 10 minutes. Check the anti-theft light again....
Most popular

What is the code for the fan clutch on a Ford F 250?

What is the code for the fan clutch on a Ford F 250? Ford F-250 fan clutch P0528 - YouTube Vehicle came in with a code pO528 for the fan clutch speed sensor fault. Checked power to fan and checking control from pcm to speed the fan up. Vehicle came in with a code pO528 for the fan clutch speed sensor fault. Checked power to fan and checking control from pcm to speed the fan up. Skip navigation Can a bad fan clutch cause an AC to not work? The guy calls back and says the fan clutch for the...
Easy tips

What kind of headlights do I need for a 1998 Mustang?

What kind of headlights do I need for a 1998 Mustang? Ford Mustang 1998, Replacement Headlight by K-Metal®. Chrome housing, clear lens. With Fluted Lens. You need all your lights to be functional for safe driving, to see the road and be seen by other drivers. Don't drive with broken or... How to adjust the headlight aiming on a Mustang? With your Pony in park or out of gear with the e brake engaged, you can now turn on your lights. Take some tape and mark off the horizontal and vertical centers of each light beam. With the centers of...
Most popular

Why is the rear hatch on my Ford Escape not opening?

Why is the rear hatch on my Ford Escape not opening? 2009 ford escape. The rear lift gate will not unlock. The rear hatch started not opening at times, then would not open at all! The electric latch mechanism had failed and had to be replaced at the cost of $210.00 including labor. Now just waiting to see what the next odd thing is that fails on this vehicle! What to do if your rear hatch won't open? Replacement Made Esay - Once you have the lift open, its an easy replacement. The trick is getting the lift open. You...
Other

Is key code a location?

Is key code a location? Vehicle KeyCodes are located on the original vehicle invoice to the dealership. There is a small white bar coded tag sent with most new vehicles that also has the key code printed on it. Dealerships should make a practice of comparing the tag's keycode numbers to the keycode listed on the invoice. How do you change the key on a Ford Escape? KEEP the ignition in Position 3 (RUN) for at least 3 seconds, but no more than 10 seconds. TURN the ignition to Position 1 (LOCK) and REMOVE the second key from the ignition....
Easy lifehacks

How do you turn off daytime running lights on a Ford Edge?

How do you turn off daytime running lights on a Ford Edge? How to Turn Off Daytime Running LightsPress your parking brake slightly until it clicks once. Locate the power distribution box in your vehicle. Remove the "DRL" fuse from the power distribution box. Consult the manual for your vehicle because there are different procedures for each one. What does DRL mean on a Volkswagen? Daytime Running Lights Daytime Running Lights: This light means that your VW Jetta daytime running lights are currently on. What are the headlights on a 2014 Ford Edge? Ford Edge with Factory Halogen Headlights 2014,...
Easy tips

How do you reset the anti-theft on a 2010 Ford f250?

How do you reset the anti-theft on a 2010 Ford f250? Wave your key in front of the dash where the ignition switch is, then in front of the radio, and try again. Another option which takes 45 minutes to work (again sometimes works) is to turn the key on and wait 15 minutes for the light to stop flashing. Then turn the key off and back on for another 15 minutes. What does the security feature on Ford PCM do? This security feature immobilizes the vehicle by disabling the fuel pump, injectors and possibly the starter, until the ignition...
Common questions

What causes black tire marks on concrete?

What causes black tire marks on concrete? The tire marks you find on your concrete driveway are actually a result of a material within the rubber tires known as polymer compound getting heated up. When they heat up they are more likely to leave those tire marks across your concrete driveway. How do you remove black rubber from concrete? HOW TO GET TIRE MARKS OFF CONCRETEApply a cleaning product such as SunSpot, a concrete degreaser, Natural Orange (or other citrus cleaner), Simple Green, or automotive brake cleaner to the affected area.Allow the cleaner to sit on the surface for a...