Other

Can a bad exhaust pipe cause a problem?

Can a bad exhaust pipe cause a problem? While the exhaust system is relatively simple in its operation, it plays an important role in engine performance. Any issues with the system or its pipes can cause problems with the drivability of the vehicle. Usually a bad or failing exhaust pipe or tube will produce a few symptoms that can alert the driver of a potential issue. 1. What are the most common exhaust system problems? In this blog, our expert technicians at Christian Brothers Automotive discuss the most common exhaust system problems, such as a faulty oxygen sensor, exhaust leaks,...
Easy lifehacks

What does p246c stand for in Ford diagnostic code?

What does p246c stand for in Ford diagnostic code? Ford Code: P246C Definition: Particulate Filter Restriction - Forced Limited Power (Bank 1) Description: The PCM monitors the diesel particulate filter for a high restriction. This DTC sets during normal vehicle operation when the diesel particulate filter pressure is greater than a calibrated amount. What does DTC stand for in Ford diagnostic code? Code: P246C Definition: Particulate Filter Restriction - Forced Limited Power (Bank 1) Description: The PCM monitors the diesel particulate filter for a high restriction. This DTC sets during normal vehicle operation when the diesel particulate filter pressure is...
Easy lifehacks

How can I lock up my transit car?

How can I lock up my transit car? Try opening the rear door driver side and operate the inside handle. then lock it all up as normal. This happened on a 10 plate transit last year, more than once. Why does transit central lock the front doors? Probably someone who wanted to lock the front doors but leave the rear doors open for getting stuff out, without having to watch who was opening the front. Probably someone who wanted to lock the front doors but leave the rear doors open for getting stuff out, without having to watch who was...
Easy lifehacks

When should I replace my reMarkable marker tip?

When should I replace my reMarkable marker tip? The durability of the marker tips will vary with the writing technique and amount of usage. Our best estimate for an average user is anywhere between three to seven weeks, hence, the 10 pen tips are likely to last between six months and upwards to 15 months depending on usage. How long does the reMarkable Marker last? The Marker is a hefty and textured stylus with replaceable high-friction tips. (Extra tips are included, and each one lasts about two months.) It doesn't have a battery, so there's no need to charge it....
Easy tips

What causes a vacuum leak in a Ford 4.6L?

What causes a vacuum leak in a Ford 4.6L? The most common vacuum leak problem is the PCV tube's elbow, where it connects to the intake manifold. Suggested Test 2: With the engine completely cold, start her up and spray around the intake manifold's gaskets to check for leaks. If the carb spray hits a spot that is leaking,... What are the symptoms of a vacuum leak? Common Symptoms of an Engine Vacuum Leak 1 Engine Running Problems. An engine with a vacuum leak could potentially run normally, but it may idle faster than usual, idle roughly, misfire, hesitate, or...
Other

How big is the transmission on a Ford Ranger?

How big is the transmission on a Ford Ranger? A 12-bolt pattern is typical of the original Mitsubishi and Mazda transmissions made for the Ford Ranger. Measure the extension housing. This is the portion of the transmission located past the bell housing and center part of the transmission. It is much narrower then the rest of the transmission unit and should measure 10 inches. How big is the repair manual for a Ford Ranger? 1996-1999 Ford Vehicles Workshop Repair Service Manual (2.9GB DVD IMAGE!) 1996-1999 Ford Vehicles Workshop Repair Service Manual (2.9GB DVD IMAGE!) Ford AeroStar Aeromax Cargo Econoline Expedition...
Other

What can I do about the grinding noise in my front seat?

What can I do about the grinding noise in my front seat? Spray the Lower control arm bushings with WD40, then go for a ride see if the noise is different or goes away. This is not a long term solution, just a way to rule out the LCA bushings. Good luck. Oh yeah on the road my noise always goes away when I press on the gas. I'm already making plans to install new hubs and bearings on the front. Why is my front tire making a rubbing noise? The tread on the tire looks fine, I know it's...
Most popular

What causes a 2006 Ford F-350 diesel to fail?

What causes a 2006 Ford F-350 diesel to fail? Liner in the fuel tank corroded and clogged fuel system causing failure of vehicle. The contact owns a 2006 Ford F-350 diesel. The contact stated that the fuel tank was rusting due to a faulty coating on the inside of the tank. Neither the dealer nor the manufacturer were notified of the failure. Are there any problems with a 6.0 liter diesel engine? Below are the most common problems associated with the 6.0 Power Stroke engine. The 6.0L Power Stroke fuel injection system operates on oil pressure, very high oil pressure....
Easy lifehacks

What was code for failed indirect fuel injector?

What was code for failed indirect fuel injector? Runs great now. My 2014 had the check engine light on last week, dealer found code P0420 and replaced the failed Indirect Fuel Injector under my extended warranty. It had been on what seemed like a very long regen prior to the Idiot Light coming on, and most likely responsible for the sensors going bad. Where is the fuel injector error code stored? Basically, this code only ever gets stored on the Powertrain Control Module of diesel engines. This code indicates that the vehicle´s PCM has detected an inconsistency between the electronic...
Other

Do grease guns have different size fittings?

Do grease guns have different size fittings? There is effectively just one size. There are some other weird ones out there, the common being button head I believe, but if it looks like a standard grease zerk it is going to be the standard size. Are Zerk fittings tapered? Taper Thread Grease Fittings are used on cars, trucks and many types of industrial machinery. The included angle of the thread for a 1/4"-28 taper thread grease zerk is 60º. What size thread are grease nipples? There are two grease fittings that are very common. These are the 1/4″-28 thread and...