Easy lifehacks

Why is there a noise coming from my alternator?

Why is there a noise coming from my alternator? Noise from the alternator could be caused by a faulty rotor shaft, rectifiers, bearings, slip rings, stator winding or brushes. You will need to carefully inspect each of these components and replace them. One sure way of confirming that the noise is coming specifically from the alternator is to use a vacuum hose. What kind of alternator does a GM 3.8L have? This article covers the majority of 3.8L Buick, Chevy, Olds, and Pontiac equipped cars and mini-vans. To see if this alternator test article covers your specific 3.8L GM vehicle...
Easy lifehacks

How many miles does a Chevy Blazer get?

How many miles does a Chevy Blazer get? Mileage: 16,115 miles Body Type: SUV Color: Gray Engine: 6 Cyl 3.6 L No accident or damage reported to CARFAX. Purchased on 10/19/19 and owned in MO until 05/12/21. Driven an estimated 16,762 miles/year. Is there a 2020 Chevy Blazer for sale? Autotrader has 16,597 Chevrolet Blazer cars for sale, including a New 2020 Chevrolet Blazer AWD LT w/ 3LT, a New 2020 Chevrolet Blazer AWD Premier, and a New 2020 Chevrolet Blazer AWD RS. What's the price of a new Chevy Blazer? How Much Does the 2021 Chevrolet Blazer Cost? The...
Common questions

Can you turn a single axle truck into a dually?

Can you turn a single axle truck into a dually? Trucks are great for hauling heavy loads and they have lots of utility space for whatever you need to carry. Thanks to mass-production techniques, you can turn your single-wheel axle truck into a dually with just a few parts and supplies. Can you convert a dually? You can leave the DRW rear axle in the truck if you don't mind the track width of the back tires being a little wider than the front. Just get your new tires and wheels, remove the front dually wheel adapters, exchange your bed...
Other

Where is the fuse on the Transmission Control Module?

Where is the fuse on the Transmission Control Module? The Transmission Control Module is labeled “TCM” it’s easy to find as long as you know the abbreviation. Where is the 4L60E fuse? You’ll find the fuse to the 4L60E located under the hood of the car or truck. It won’t be in the fuse panel that you’d think of when looking under the dash. It’s under the hood, usually on the driver’s side. What are the symptoms of a bad transmission speed sensor? Symptoms of a Bad or Failing Transmission Speed Sensor. 1 1. Harsh or Improper Shifting. Without a...
Other

Should you use anti seize on exhaust bolts?

Should you use anti seize on exhaust bolts? If you are reusing exhaust manifold bolts (which we don't recommend), apply a metal fortified anti-seize to your manifold bolts. If you've just removed the broken bolts and ready to complete the repair, chase the threads clean and use fresh OEM bolts for best results. How to get rid of stuck exhaust manifold bolts? Learn how to remove stuck exhaust manifold bolts or studs. Wades shows you a little-known trick to help loosen up some of those old, seized and corroded exhaust manifold bolts. This can be a life saver tip and...
Common questions

Can you install side exhaust on a 1969 Corvette?

Can you install side exhaust on a 1969 Corvette? Additionally, there are no problems with fuel or brake lines being too close, causing more problems. Don’t forget that the GM factory installed side exhaust on 1968–1969 Sharks, making the installation possible on any Shark, albeit 1975 and up, catalytic converter models. What kind of exhaust system does a corvette have? There are no differences on the sound that factory-style side pipes emit; big-blocks sound throatier because as the fiberglass packing deteriorates the sound deepens. This Shark-style chassis has a set of factory side pipes on a 300-hp engine. The smooth-flowing...
Most popular

Is it normal for a Chevy Cobalt to run at 194F?

Is it normal for a Chevy Cobalt to run at 194F? Some websites say this is normal, others say their Cobalts run at 194f.The 221Fmay be normal for many, but I don't think it is right to have to constantly depend on the cooling fan to keep the engine temperature in check. My previous 2001 Sunfire 2.2 auto ran at 194f and the rad fan seldom came on, maybe once a year. What should the water temp be in a Chevy Cobalt? So a normal temp on hot days in heavy intern driving in Az, Texas, florid or S.Calif., may...
Easy tips

What are the symptoms of a p0106 DTC code?

What are the symptoms of a p0106 DTC code? The following could be symptomatic of a P0106: 1 Engine runs rough. 2 Black smoke at tailpipe. 3 Engine will not idle. 4 Poor fuel economy. 5 Engine misses at speed. What causes a p0106 signal on a MAP sensor? A P0106 could be caused by: 1 Bad MAP sensor. 2 Water/dirt intrusion affecting MAP sensor connector. 3 Intermittent open in the reference, ground, or signal wire for the MAP sensor. 4 Intermittent short in the reference, ground, or signal wire for the MAP sensor. 5 Ground problem due to corrosion...
Easy tips

What kind of kickdown switch do I need for TH400?

What kind of kickdown switch do I need for TH400? B&M kickdown switch kits are perfect for use when swapping out a TH350 or TH700R4 for a TH400. These kits mount to the factory throttle cable bracket for easy kickdown control. Can A B and M kickdown switch be swapped? B&M kickdown switch kits are perfect for use when swapping out a TH350 or TH700R4 for a TH400. These kits mount to the factory throttle cable bracket for easy kickdown control. What type of question would you like to submit? (order, shipping, returns, etc.). a question about this Product. How...
Common questions

How does a non can communication system work?

How does a non can communication system work? “Networking” is the process of modules sharing information through different communications protocols or “languages.” Protocols on conventional, non-CAN systems usually switch from zero volts to a specified voltage to create an on/off signal that makes up a communications protocol. What to do if your MDI says no connection? If your MDI Manager shows a connection with your MDI and says software is compatible with pc, it is OK. Reconnect the MDI device and load software again. Follow the correction connection procedure and settings: Once install and run the MDI manager, power up...