Other

What was the problem with the Toyota 22RE engine?

What was the problem with the Toyota 22RE engine? There was an internal bulletin for Toyota factory technicians back in the mid 80’s about a similar issue with 22RE engines. The issue was an internal programming problem with the ECU. What should the idle speed be on a 22RE? We also recommend going a hair tighter than the factory says too. .007” on the intake and .011” on the exhaust side. If it’s your first time adjusting valves, TAKE YOUR TIME AND TRIPLE CHECK YOUR WORK. It’s not rocket surgery, but if it’s not done correctly, things can get ugly...
Other

What rear end came in a 1968 Mustang?

What rear end came in a 1968 Mustang? The V8 versions of a '68 up Mustang came with 5 bolt axles/hubs and either an 8 or 9 inch rear end. How wide is a 1968 Mustang rear end? For us, it started with a search for a performance replacement for the lame 8-inch rearend in our Car Craft '67 six-cylinder Mustang....How To Spot, Build, And Swap In the Ford 8.8 Mustang Rearend.Vehicle ApplicationAxle Width (inches)'62-'67 Chevy II58 71/48'68-'74 Nova59 51/48 What size rear end does a 66 Mustang have? 66 Mustang original i6 rear end size - 8" or 7.25"...
Easy tips

What causes a crankcase to have low compression?

What causes a crankcase to have low compression? Worn pistons/rings The most common cause of low compression is worn pistons or piston rings. Anytime the pistons or their corresponding rings have leaks, air will leak from the crankcase into the compression cylinders. What should the compression rate be in a car? Insert the compression gauge extension and screw it in. Have someone crank the engine and watch the gauge until you reach maximum compression. A healthy engine should have 100 PSI per cylinder. What to do if your compression ratio is low? Use a leak-down-tester to check where the compression...
Easy tips

How fast can a 69 Corvette go?

How fast can a 69 Corvette go? Top Speed: 170 mph (Est.) What was the horsepower of the 1969 Corvette? The horsepower was 430 hp when it should really have been 560 hp. The 1969 Corvette build cycle was from September 1968 until December 1969. One of the longest build cycles for a US car. Serial Numbers: 194379S700001 through 194379S738762 -- For Convertibles, the fourth digit is a "6" Where do you find the VIN on a 1969 Corvette? Following the three characters are the last six digits of the vehicle serial number. The last six digits should match the...
Other

Why do hydraulic roller cams require different timing chain sets?

Why do hydraulic roller cams require different timing chain sets? These two cam types require different timing chain sets, because the hydraulic roller cams have a stepped nose like the LT1 engine as described later in this section. In 1992, a balance shaft was incorporated in this engine, which necessitated a third timing chain setup to drive both the cam and the balance shaft. What is the part number on a Chevy Cam? The ID number will consist of either eight or nine digits; the last four numbers identify the cam and its specific application. Match the number to a...
Easy tips

How did the Mercedes W123 bubble get its name?

How did the Mercedes W123 bubble get its name? This is a very special 300D turbo diesel sedan. It was named "Bubbles" by the previous owner because she felt the color looked like the color of champagne. Rather than try to tell you all about this car, I am going to have you watch a number of videos below. The first video will explain how we came to be owners of this pretty W123. Where is the fuel tank sender on a Mercedes 126? On the 126 chassis it is located under a large plastic plug on the left side...
Most popular

Which is the best distributor for a 350 Chevy?

Which is the best distributor for a 350 Chevy? This GM SBC HEI distributor model is made for performance with its heavy-duty construction and hardened steel gears that are built with durability and long life in mind. With this high level of durability, this great option will work for your 350 Chevy for a very long time without issue. What are the distributors for the Chevy 5.7L? Distributor, Pro-Billet Street, Magnetic Pickup, Vacuum Advance, Chevy, Big/Small Block, Each Distributor, Optispark II, Optical Trigger, Electronic Advance, Buick, Chevy, Pontiac, 5.7L, LT1, Each Distributor, Pro-Billet, Small Base, Magnetic Trigger, Mechanical Advance, Chevy,...
Easy lifehacks

What kind of truck is the 1979 Ford F150?

What kind of truck is the 1979 Ford F150? 1979 Ford F150 Pickup The Ford F150 trucks were introduced to the United States in 1948 and they were known as the Ford Bonus-Built trucks. They were built on a dedicated truck platform unlike earl... More Info › Solid Ford truck. V8 (351 Manual 4 speed) Manifolds and complete exhaust and muffler replaced in 8/2019. Are there any recalls on 1979 Ford F150? Recall ID 79V035000 addressed faulty steering knuckles on 62,000 units. Substandard welds on wheels actually resulted in two recalls (IDs 79V208000 and 79V185000), while two other recalls (IDs...
Easy lifehacks

Which paint is used for car painting?

Which paint is used for car painting? What are the types of automotive paint finishes? Metallic Paint: In basic form, the metallic paint is the application of colour followed by an additional layer of lacquer (also known as the clear coat). What are the three basic types of automotive paints? The four basic types of auto paint are acrylic lacquer, acrylic enamel, acrylic urethane, and water-based. Urethane paints are newer than enamels, are more expensive and more trouble, but they lay down easily like lacquer while having the toughness of enamels. Is primer a paint? Primer is a paint product...
Common questions

How to adjust the firing order of a valve?

How to adjust the firing order of a valve? You split the firing order in two halves. 153 624 When the lifters of #6 are "rocking", adjust #1. When the lifters of #2 are rocking, adjust #5. When the lifters of #4 are rocking, adjust #3. This will continue on every 60 degrees with #1 rocking, adjust #6; #5 rocking, adjust #2; and #3 rocking, adjust #4. Can a valve be adjusted for a 1 cylinder engine? You have touched on another question that gets asked a lot. Initially adjusting the valve train. With the engine at #1 TDC (firing),...