Common questions

How do you replace the radiator on a Malibu?

How do you replace the radiator on a Malibu? Remove the bolts at the top of the radiator mount by turning them counterclockwise. The mount, or mount plate on some models, will release the radiator. Slide the radiator straight up and away from the engine. Position the new radiator at the top of the channel, then slide it into place. What to do if water comes out of radiator? Open the pressure cap and petcock to drain the radiator. Make sure the drainage pan is underneath the petcock to catch the cleaner and distilled water. The water may be brown...
Other

What to do if your security system breaks on a GM car?

What to do if your security system breaks on a GM car? On older GM cars two small wires will break near the tumbler which will activate the system. In this case the tumbler must be repaired or replaced. Call to the dealer, this is their response: Hold the panic button on the key fob for 2 seconds. Close all of the doors and while using the key lock and use the key to unlock the lock the driver's door. What to do if your car security system is out of sync? Using the owner's manual remove the fuse which...
Other

What happens if you cross a spark plug wire?

What happens if you cross a spark plug wire? Every engine manufacturer provides a service manual detailing the correct firing order of their cylinders. When one or more spark plug wires are crossed, the engine may not run, or runs roughly as the timing of fuel/air compression does not align with the delivery of the spark. Is it OK for spark plug wires to touch? As long as the spark plugs and wires are good not a problem for the wires to touch. They don't fire at the same time and the distance between wires is always more than the...
Easy tips

Is it possible to swap a GM LS engine?

Is it possible to swap a GM LS engine? GM did everyone a huge favor by keeping the same bolt pattern. This makes it technically possible to bolt these transmissions together, otherwise this wouldn’t be an option for your LS engine swap. In the classic car community this pretty much makes it as good as done. What kind of engine can I swap in a Camaro? Sticking with tradition, GM introduced the Gen III line of V8 engines that share similar components and dimensions to allow for easy swaps between various models. With such great interchangeability, budget engine swaps can...
Easy tips

What happens to the coolant in a blown head gasket?

What happens to the coolant in a blown head gasket? As a result, the coolant can enter the combustion chambers, where it is burned during engine operation. As was mentioned above, a blown head gasket can allow the coolant to be burned inside the engine. How can you tell if you have a blown head gasket? From a purely visual perspective, the most surefire evidence of a blown head gasket is the presence of leaked coolant along the gasket surface. In the majority of cases, leaks occur between the engine’s combustion and cooling components. What makes the head gasket on...
Easy tips

How to remove serpentine from Chevy Silverado 5.3?

How to remove serpentine from Chevy Silverado 5.3? Slowly rotate the crankshaft in a clockwise direction until the belt  (2) fully seats on all pulleys. (Image 3) Inspect the drive belt  (1) for proper installation and alignment. Rotate the balancer  (1) and additional 360 degrees to ensure proper belt installation. Why is the serpentine belt important on a Chevy Silverado? If you didn't already know, the serpentine belt or drivebelt on your truck's engine is very important in the proper operation of the engine. It drives critical engine components like the alternator, power steering pump, and water pump as well as...
Easy lifehacks

Is the Chevy Avalanche tail light still working?

Is the Chevy Avalanche tail light still working? Almost 5 months in and it is still working great. Easy install on a 2002 Chevy avalanche. Also needed the gm pigtail connector for the right tail/turn as it burned up when the original part went bad. Update: spoke to soon. Now after 6 almost 7 months the product just failed again burning the pigtail connector at this board. Why is my Silverado tail light not working? Suspect this part if your having light issues in the back as all lights go through this, my 06 Silverado had one license plate socket...
Common questions

Que tipo de cafe se cultiva en Costa Rica?

¿Qué tipo de café se cultiva en Costa Rica? En Costa Rica las principales variedades de uso comercial de café según el Instituto de Café de Costa Rica son Caturra, Catuaí, Híbrido F1 y Venecia (ICAFE, 2011). ¿Cómo se llama el café que se produce en Costa Rica? En Costa Rica, los tipos que más se cultivan son Catuaí y Caturra, pero también producen: Venecia, Híbrido F1, Typica, Mundo Novo, entre otros. Estas se caracterizan por ser de muy buena calidad, pero también de alta productividad. ¿Dónde se produce el mejor café de Costa Rica? El mejor café de Costa...
Most popular

Can you install lowering springs yourself?

Can you install lowering springs yourself? The process is not difficult, so anyone with garage access and a little know-how can accomplish this modification. Since lowering springs are designed to work with your existing factory suspension, they can simply replace your coil springs. Will lowering springs ruin my suspension? Poorly done or extreme lowering can cause suspension and steering parts to contact each other, the wheels or the tires. It could also cause tires to rub the body during turns or going over bumps. How long do Lowering springs take to install? takes about 4-6 hours on the parking lot...
Most popular

When should you sleeve a block?

When should you sleeve a block? Installing a repair sleeve can often save the block if a cylinder has excessive taper wear, or is cracked, scored or otherwise damaged, and boring out the damaged cylinder. Why do you sleeve a block? The primary reason for sleeving an engine to either repair a cylinder bore or protect it from damage in the first place. Sleeves can also be used to restore a particular bore size if a cylinder has to be “bored out” to repair a cracked or otherwise damaged engine. Simply put, a dry sleeve does not contact the coolant....