Common questions

When do you Know Your freeze plug has blown?

When do you Know Your freeze plug has blown? If you notice a low coolant level in the coolant reservoir and discover no visible leaks, it could mean the freeze plug has blown. If you notice a strong smell of heated coolant, it could mean the freeze plug has blown, and the coolant is leaking from your engine. Where are the freeze plugs on an engine block? If you look on the side of an engine block you will see a line of circular depressions about an inch and a half in diameter and about a quarter of an inch...
Easy tips

What is the difference between Ford f150 SuperCab and SuperCrew?

What is the difference between Ford f150 SuperCab and SuperCrew? You can immediately spot the difference between the SuperCab and SuperCrew due to their doors. A SuperCab has four doors, however, the rear ones are smaller and open backward, while the SuperCrew has four full-size doors that open all in the same direction. Where can I find a Ford F150 front door? To find your Ford F150 Pickup Front Door from a RECYCLER NEAR YOU, just enter the YEAR of your vehicle and your ZIP code in the above form and press the "FIND" button. (What you see below is...
Easy tips

What is the trouble code for a Solenoid B?

What is the trouble code for a Solenoid B? Most automatic transmissions incorporate at least three solenoids that are solenoid A, B and C. The trouble codes related to the "B" solenoid are codes P0775, P0776, P0777, P0778 and P0779. The code set is based on the specific malfunction that alerts the PCM and illuminates the Check Engine Light. What is the code on my Ford Explorer? I have a 2003 Ford Explorer, v6 with 102,000 miles. The Overdrive light and check engine light came on and set code P0775. I can't find any info on that code. What causes...
Common questions

How do you fix a hole in a tie rod?

How do you fix a hole in a tie rod? Insert a water activated compressed swell plug into the exposed tie rod hole. Hand tighten by turning the coupler end. Once snug, lightly tap the end of the coupler with a hammer until the coupler is flush with the wall. Finish tightening to a snug fit with a 3/8 inch (9.53 millimeter) socket or a 3/8 inch (9.53 millimeter) nut driver. How much does it cost to replace a tie rod? If the tie rod sways between sides, you need to replace it. It won’t take very long for a...
Other

What are common reasons my Ford Expedition overheats?

What are common reasons my Ford Expedition overheats? What are common reasons my Ford Expedition overheats? While there are a variety of reasons your Ford Expedition is overheating, the most common 3 are a coolant leak (water pump, radiator, hose etc.), the radiator fan, or a failed thermostat. What happens when a head gasket gets blown on a Ford van? Go to: TEST 2: Compression Pressure And/Or Exhaust Gas Exiting The Radiator. Here's why: Normally (about 90% of the time) when a head gasket gets blown on a 4.6L, 5.4L Ford van (or car, pick up, SUV), coolant will enter...
Other

Why does my diesel engine keep running hot?

Why does my diesel engine keep running hot? Follow Kent's video series If your diesel engine is showing signs of overheating, don't panic until you do some detective work. There could be a number of reasons why your gauge is "running hot." It could be something as simple as a faulty sending unit or thermostat. How to troubleshoot an overheating car engine? Checklist for troubleshooting an overheating engine 1 RAW WATER SYSTEM. The most common cause of engine overheating is a lack of raw water flow. 2 COOLANT LOOP. 3 ENGINE OVERLOAD. 4 VALVES, INJECTORS, CYLINDERS. 5 TEMPERATURE GAUGE AND...
Other

How to loosen a tensioner on a car?

How to loosen a tensioner on a car? How to Loosen a Tensioner 1 Open the hood and locate the drive belt (s). Either locate the serpentine belt routing diagram in the engine compartment, or refer to the repair manual. 2 Determine the type of tension applied to the belt you're replacing. 3 Locate the belt tensioner per belt routing diagram. How is loosening a tensioner pulley done? Loosening the tensioner pulley is accomplished by pulling it in a direction that gives slack to the serpentine belt. This action enables the belt to be removed and for replacement or repair...
Other

Why is my door rattling when closed?

Why is my door rattling when closed? It's caused by a gap between the doorstop (a part of the frame) and the door, which is providing excess room for the door to move around in. When you find the door rattles when closed in its frame, all you need to do is slightly adjust the latch plate that the door latch sits against. What mean rattling? intransitive verb. 1 : to make a rapid succession of short sharp noises the windows rattled in the wind. 2 : to chatter incessantly and aimlessly. 3 : to move with a clatter or...
Easy tips

How to install OBD2 odometer correct tool for Ford?

How to install OBD2 odometer correct tool for Ford? OBD2 Odometer Correct and Immobiliser Key Programming Tool for Ford It can read and write into EEPROM file, it can read out immo code, and directly edit key position byte, then replace the original key to a new key, also it can read out and write into the synchronized bytes of instrument and engine, then directly synchronize without programming. When do you push the OD button on a Ford truck? Fords transmissions would shift in to OD about 35 to 42 mph with light throttle pressure ( gas pedal up) and...
Other

What kind of thermostat does Ford 351C use?

What kind of thermostat does Ford 351C use? It was used for many production vehicles from Ford, AMC and AM General, and is most frequently discussed in the context of the Ford 351 Cleveland engine. Today, Robertshaw style thermostats are available from several US, Chinese and Australian labels (but not Robertshaw, which no longer sells direct to consumer). Where did the Ford 351W engine get its name? Not to be confused with Ford's 351 "Cleveland" engine, the 351W gets its name from Ford's Windsor, Canada, plant, where it was briefly manufactured. Is the Ford 351M the same as the 400?...