Common questions

What do you do when your phone is not pushing?

What do you do when your phone is not pushing? Restart the device. It may sound pretty basic, but when your touch screen stops working, simply restarting your touch screen device is usually all it takes to fix the problem. Clean the touch screen and screen protector. What to do when your touch screen doesn't work? Press and hold the power button until the screen becomes black; After 1 minute or so, hold the power button again to power on the device. In many cases, the touch screen will respond normally after the device reboots. 2. Why does my hp...
Other

How do you hotwire a four wheeler without a key?

How do you hotwire a four wheeler without a key? Use A Screwdriver Basically you just hammer a screwdriver into the ignition and turn it on as if it were the key. The screwdriver will brake the pins in the lock allowing you to turn the ignition on. I don't recommend this method because you could damage the ignition and not get the quad to start anyway. What happens if you lose your car keys and have no spare? This does not only apply to car keys, but to house keys and commercial building keys as well. It is one...
Common questions

Is there a problem with the 5.7 Hemi engine?

Is there a problem with the 5.7 Hemi engine? I'm in the same boat with a 2013 5.7 Hemi. Check engine light came on at 129,000 and started idling rough. The dealer read the code and told me #8 wasn't firing. How much does it cost to replace a hemi engine? It will cost you between $5,600 and $13,000 to replace a 5.7 Hemi engine. If you go for remanufactured Hemi engines, it will cost you between $2,900 and $4,000 to purchase before you have a professional install it. The installation cost will depend on whether you do it or...
Easy lifehacks

What order do you tighten oil pan bolts?

What order do you tighten oil pan bolts? To install:Install the oil pan bolts in sequence. Tighten the oil pan bolts to 18 ft. Install the A/C compressor bolts. Tighten the bolts to 18 ft. On the 2.0L engine, install the intercooler pump bracket bolts. Install the engine drive belt.Lower the vehicle.Fill the engine oil to the proper level. Do you need to oval out a bolt to install an oil pan? Start all the nuts or bolts and finger tighten. If using bolts, the pan may need a little rocking to get the pan and gasket holes lined up...
Easy lifehacks

How to keep your Ford a / C drain clear?

How to keep your Ford a / C drain clear? Ford A/C Quick Tips: #2 Keeping your A/C Drain Clear! - YouTube If playback doesn't begin shortly, try restarting your device. Videos you watch may be added to the TV's watch history and influence TV recommendations. How to unclog your car AC drain line? The sloshing noise may be especially noticeable when making turns as well as having a damp floorboard. Here is a quick fix using compressed air to unclog a Mitsubishi Galant AC drain line but fix can be used for many other vehicle models. Loading... Why is...
Common questions

How do I get my 2005 Dodge Ram out of limp mode?

How do I get my 2005 Dodge Ram out of limp mode? To get the Dodge Ram 1500 out of limp mode you need to stop and shift to park. Turn the car off and wait 30 seconds, now turn it back on and it will be out of limp mode. How to fix a Dodge engine hesitation problem? How to Fix a Dodge Engine Hesitation Problem 1 Park your Dodge vehicle in a safe place and open the hood. 2 Remove the air cleaner assembly from the top of the engine and locate the TPS sensor. 3 Check the...
Easy lifehacks

What does pressure sensor do on Chrysler p0452?

What does pressure sensor do on Chrysler p0452? The sensor output voltage to the Engine Control Module ( ECM) increases as pressure increases. The EVAP control system pressure sensor is not used to control the engine system. It is used only for on board diagnosis. Need more information on how to fix the P0452 CHRYSLER code? What does the code p0452 mean on an EVAP system? Perform a visual inspection of the wiring and the EVAP control system pressure sensor. The code P0452 is often be associated with damaged or corroded wiring or a failed or unplugged sensor. Courtesy: www.etecownersgroup.com...
Easy lifehacks

How much does it cost to replace a front crankshaft seal?

How much does it cost to replace a front crankshaft seal? A factory replacement part costs about $15 and a Timken seal costs about $9. The total job cost would be about $300 using OE parts and about $309 using aftermarket parts. 2000 Ford Expedition with a 5.4-liter engine The estimated labor time is around 1.6 hours. A factory part costs about $15 and a Fel-pro seal costs about $6. What kind of sealer do I need for my crankshaft? BlueDevil Rear Main Sealer is specifically designed to target your crankshaft seals for repair. BlueDevil Rear Main Sealer is a...
Other

When do I feel like my car is losing power?

When do I feel like my car is losing power? You will notice this especially when you go on a long road trip or use a city car on open roads. If you are overtaking while going uphill and have the air conditioning on, you will notice how the engine can feel like it is losing power. There is no need to worry. Why does my car lose power when I press the accelerator? When you press the accelerator, it sends more fuel through the filter and not as much can get through. Also, a dirty fuel filter is a...
Most popular

How do I reset my 2006 Dodge Ram 1500?

How do I reset my 2006 Dodge Ram 1500? Turning Off the RAM 1500 Check Engine LightIdentify your battery's negative cable.Disconnect the negative cable from the battery.Wait 20 minutes so that all systems have shut down.Reconnect the negative cable. Why does my Dodge Ram won't engage? From a standstill, it won't always engage until you move. Bristol , Tn. Like stated above try to engage while rolling say 10 - 20 mph , or just drive it fwd or reverse . If still no luck make sure you have a good connection on the plug for your 4wd actuator ,...