Other

How many clutches does an automatic transmission have?

How many clutches does an automatic transmission have? The inside of an automatic transmission has a planetary gearset, a set of bands, a set of three wet-plate clutches, a hydraulic system, and a large gear pump. Which clutches are automatic? An automatic transmission does have a clutch system, but usually only a mechanic would refer to it as such. Your automatic transmission performs the same function as a manual transmission – it just does it a little differently. How do you tell if you need a new clutch automatic? If you're experiencing any of the below symptoms, you may need...
Easy lifehacks

Why is my 1979 Ford F-100 hard to start?

Why is my 1979 Ford F-100 hard to start? 38 people found this helpful. My 1979 F-100 300 cu. in. 6 cyl. would be very hard to start at times and would often die while driving down the road (and would start back up while still rolling) I replaced the fuel pump that is on the side of the engine-no help (but solved an oil leak as it was loose). Why are my turn signal lights not working? Check for damaged or burned-out bulbs in all turn signals on that side. Alternately, the ground on either light could have gotten...
Most popular

What was the factory 534 Ford FE used for?

What was the factory 534 Ford FE used for? the 534's were "industrial" engines and also used as marine engines...there are 2 twin turboed 534's for sale here for $500 they seem to need to rebuilt but all the parts are there! from Vacaville, CA. We had the 477's and 534's in our F-800 and 900 fire engines. Good engines but they needed a lot of help. What kind of torque does a Ford 534 have? Wicked torque, way better than the GM Diesels were in the 80's and 90's. I would always grab the old Ford with the 534...
Easy lifehacks

Can a Cobra be converted to a Mustang?

Can a Cobra be converted to a Mustang? For example its now possible to fit the entire engine, gearbox, front and rear suspension complete with ABS brakes, from a late 90's Cobra, into a 67-73 Mustang. After conversion the external visual appearance of the car is not changed, and so you need not know the car has been modified until you check under the bonnet or look underneath. Can a classic Mustang be converted to a modern car? Effectively this means you can have a car with the fabulous looks of a classic mustang, but with the driving dynamics, responsiveness,...
Easy lifehacks

Where is the VIN number on a 1953 ford F100?

Where is the VIN number on a 1953 ford F100? Re: VIN Location on 1953 F100 On our '53 F-100 Panel Truck the VIN is on the data plate on the inside of the glove box door. Where is the VIN number on a Ford F100? The first one is in the engine compartment, just below the alternator on two-wheel-drive pickups or just behind the front axle on four-wheel-drive pickups. The second number is stamped just under where the seat would be located. Would you buy a old truck with no door VIN tag? Legally, in most states, a vehicle...
Easy tips

What kind of engine did Chevy trucks have in 1964?

What kind of engine did Chevy trucks have in 1964? Chevy trucks produced in 1964 are part of the modern V-8 engine era of trucks. The standard engines were 230 and 292 cubic-inch, six-cylinder engines for all two-wheel drives. In 1964, these engines were available for four-wheel drive pickups also. Where is the fuel pump on a Chevy 292? For instance, the 292 fuel pump was on the opposite side of the engine from where it was found on the other six-cylinder Chevy engines. The cylinders of the Chevy 292 engines were numbered from the front of the engine to...
Easy lifehacks

Is Corvair dangerous?

Is Corvair dangerous? The Corvair relied on an unusually high front to rear pressure differential (15psi front, 26psi rear, when cold; 18 psi and 30psi hot), and if one inflated the tires equally, as was standard practice for all other cars at the time, the result was a dangerous oversteer. How many horsepower does a Chevrolet Corvair have? The Corvair engine received its first size increase to 145 cu in (2.4 L) via a slight increase in bore size and was rated at 98 hp (73 kW; 99 PS). The base engine was still rated at 80 hp (60 kW;...
Other

When did the Ford Pinto go into production?

When did the Ford Pinto go into production? By December 1968, the basic design concept was approved by Ford Product Planning, but there was a catch: Lee Iacoccawanted the Pinto to be in dealer showrooms by the 1971 model year, condensing the typical 43-month development cycle into just 25 months. What kind of suspension did the Ford Pinto have? Suspension was by unequal-length control arms with front coil springs; the live rear axle was suspended on leaf springs. The rack and pinion steering optionally had power assist, as did the brakes. On September 11, 1970, Ford introduced the Pinto under...
Most popular

Does synthetic transmission fluid vs regular?

Does synthetic transmission fluid vs regular? A synthetic product provides more resistance to oxidation and can even improve your overall fuel economy. Because a synthetic-based fluid can be engineered more exactly for viscosity, (the thickness of the fluid) it can often meet lubricating and viscosity standards better than a petroleum-based product. Can a Synthetic ATF be used with a traditional ATF? As almost all synthetic ATFs are compatible with traditional ATFs (you can mix the two together so long as the synthetic ATF is the same grade), synthetic ATFs are beginning to dominate. However, there are a large number of...
Other

How do you install a new column on a coupler?

How do you install a new column on a coupler? To install a new column, line it up inside the coupler and fasten it to the dash. The wheel on the new column needs to be pointed straight ahead. If yours had the mechanical shift indicator, install this on the new part before raising it all the way and cinching it up. Install the pinch bolt so it's tight. How do you install a steering column on a car? Install the pinch bolt so it's tight. Reinstall the boot over the coupler. Reconnect any cables or wires you disconnected. Reinstall...