Common questions

How much does it cost to drive Sydney to Melbourne?

How much does it cost to drive Sydney to Melbourne? The total cost of driving from Sydney, Australia to Melbourne, Australia (one-way) is $102.41 at current gas prices. The round trip cost would be $204.82 to go from Sydney, Australia to Melbourne, Australia and back to Sydney, Australia again. Regular fuel costs are around $4.70 per gallon for your trip. How much does it cost in fuel to drive from Brisbane to Melbourne? The total cost of driving from Brisbane, Australia to Melbourne, Australia (one-way) is $193.84 at current gas prices. The round trip cost would be $387.67 to go...
Other

How is a Jake Brake activated?

How is a Jake Brake activated? The Jake Brake is actually an engine retarder, using the kinetic energy of the vehicle's engine to slow the vehicle without using the service (foot) brakes. When activated, the engine brake alters the operation of the engine's exhaust valves so that the engine works as a power-absorbing air compressor. What does a no Jake Brake sign mean? “No Jake Brake” signs are common in residential areas. In a nutshell, these are signs prohibiting truckers from using a braking method that is very loud. What causes a weak Jake Brake? The Jakes will must likely...
Easy lifehacks

Which is faster 70 miles per hour or kilometer per hour?

Which is faster 70 miles per hour or kilometer per hour? How fast is 70 miles per hour? What is 70 miles per hour in kilometers per hour? 70 mph to km/h conversion. A mile per hour is a unit of speed commonly used in the United States. It is equal to exactly 1.609344 kilometers per hour. A kilometer per hour is a unit of speed. How to calculate the distance in one hour? Example 1: ---------------------------------- Speed: 50 mile per hour (km/h) Distance: 70 miles Time = Distance / Speed Time = 70 km / (50 km/h) Time =...
Other

Do fuel injectors need to be flushed?

Do fuel injectors need to be flushed? CARS.COM — Cleaning fuel injectors is a service frequently recommended by dealers and repair shops. But unless there are noticeable signs of clogged fuel injectors (such as a rough idle, stalling, poor acceleration or high emissions levels), it might not be necessary. What happens when a fuel injector leaks in a Dodge Ram? A leaking injector can cause all of the problems listed above, as well as: Thin Oil – When a fuel injector leaks, all of that fuel is not getting burned in the combustion chamber. Any gas that is not fired...
Other

How do you change the throttle on a Dodge Dakota?

How do you change the throttle on a Dodge Dakota? You can remove the stock throttle body by loosening the four bolts that hold it in place. Install the new throttle body and gasket via the included instructions. Upgrade your Dodge's Engine Control Unit (ECU). How much is the Dakota throttle position sensor? Shop AutoZone for Dodge Dakota Throttle Position Sensor (TPS). 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only Why does my 98 Dodge Dakota not idle? Had the same problem with my 98 Dakota. It was just the Negative battery end. For some reason when the...
Easy tips

What is normal fuse?

What is normal fuse? The standard ampere ratings for fuses (and circuit breakers) in USA/Canada are considered 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 1000, 1200, 1600, 2000, 2500, 3000, 4000, 5000, and 6000 amperes. Where to find the information on a fuse? As these fuses are larger in size, there is usually a lot more information printed on the fuse body. This information that is likely to be found on the fuse is summarised in the following table....
Common questions

How to fix a window with a blown fuse?

How to fix a window with a blown fuse? 1 Locate and check the fuse for the problematic window motor. If it's blown, replace the fuse. 2 Remove the door panel. Locate the securing screws, usually behind covers or trim, and undo them. 3 Check the electrical input on the power and ground wires, which are generally the two largest wires connected to the window motor. ... How to fix a bad electric window switch? Attach the multimeter to the wires, then activate the window switch with the car's key in the on position. If you are getting power in...
Common questions

What should voltage be on Dodge Dakota Body Control Module?

What should voltage be on Dodge Dakota Body Control Module? The 12v square wave selection on the 20-volt scale provides a good view of the bus activity. Voltage on the bus should pulse between zero and about seven and a half volts. The PCI Bus failure modes are broken down into two categories. Complete PCI Bus Communication Failure and individual module no response. What is the bus circuit on Dodge Dakota? The PCI bus circuit is identified as D25 and is violet with a yellow tracer. Additional tracer colors may be added to the yellow in order to distinguish between...
Most popular

Can a dead battery start a Dodge Journey?

Can a dead battery start a Dodge Journey? This video shows you how to jump start a dead battery in your 2010 Dodge Journey. If you get into your Journey, turn the key, and your car doesn't start (you may hear nothing or a clicking sound from the engine bay), you have a dead battery and need a jump-start. What causes a Dodge Journey to not start? If your Journey has push start/stop button, then its possible that your vehicle may not start due to weak key fob battery. Don’t worry, you can still start your vehicle – the battery...
Common questions

How many O2 sensors does a 2007 Chrysler 300 have?

How many O2 sensors does a 2007 Chrysler 300 have? Oxygen sensors are located before and after the catalytic converter. A vehicle may have two to five oxygen sensors, and sometimes even more. What does P0300 stand for on a Chrysler 300? Chrysler 300 P0300: Engine Misfire Detected. P0300 is one of the most common OBDII codes that occurs in the Chrysler 300. It stands for: P0300 is certainly a cause for concern, and can be a threat to the drivability the Chrysler 300. It will often be accompanied by codes P0301-P0308. What are the symptoms of a Chrysler 300...