Other

What can a shaft speed sensor be used for?

What can a shaft speed sensor be used for? Our speed sensors output shaft speed via PNP, NPN, or 4-20 mA. That data can be used by facilities to monitor machinery and safeguard equipment. Monitoring shaft speed is a fundamental aspect of hazard monitoring and should be utilized by any facility with rotating shafts. Where is the transmission speed sensor located on a transmission? The Vehicle Speed Sensor (VSS) is located on the right rear of the transmission near the tail shaft. Also asked, what happens when a transmission speed sensor goes bad? When there are symptoms of a bad...
Other

Why is my magnetic door lock not working?

Why is my magnetic door lock not working? Electrical malfunctioning. Electrics mainly come down to three main problems - poor power supply, issues with the electronic equipment/software, and low-quality cables. Power supply cannot perform as requested in case of power outages. Cables can be either too thin or break easily. Failure to release and lock. What causes a door lock relay to not work? Power door locks do not function. Power door locks that do not function are another common symptom for a problem with the door lock relay. If the power door lock relay fails, it will cut off...
Other

Can a supply line be loose on a Cummins Engine?

Can a supply line be loose on a Cummins Engine? This is also a good way to verify that the injector pump’s shut down solenoid is allowing fuel to the injector. If your supply fuel line is loose, it is possible to draw air into the fuel system at that point, so if you suspect you are not getting rid of the air in the system check your supply line connections. What should fuel pressure be in a 12 valve Cummins Engine? If your supply fuel line is loose, it is possible to draw air into the fuel system at...
Easy lifehacks

Is Saturday a good day for a wedding?

Is Saturday a good day for a wedding? Hands down, Saturday is the most popular day of the week for weddings. Many people have off from work, and it gives out-of-town guests Friday evening and Saturday morning to travel. They're more affordable than Saturday and Sunday weddings, and the venues couples want are more available. Can you get married on the weekend in Florida? As soon as a license for getting married in Florida is obtained, a wedding ceremony can be performed anywhere in the state. Those who can't wait can be married right away in the clerk's office, usually...
Most popular

Can you pull an engine with the torque converter?

Can you pull an engine with the torque converter? If you try to separate the transmission from the engine in the car, with the torque converter still attached, you have to be able to perfectly separate the two along that linear line, until the input shaft clears the torque converter, allowing the engine to be lifted up and out. Can a torque converter be removed from a trans? I'd add that if you're planning on reinstalling the trans the torque converter will have to come off. While torque converters do slide off, they don't just slide on. You need to...
Common questions

Why is my lift pump leaking?

Why is my lift pump leaking? The O-ring for the push button is usually the cause of a lift pump leak. The button is made of plastic so be carefull when you remove it. You can do that without having to remove the lift pump. What causes a fuel pump to leak at the bottom? Fuel System Leaks Most mechanical fuel pumps have a weep hole on the bottom of the unit. When the internal diaphragm leaks, fuel escapes through the weep hole to notify the vehicle owner of a malfunction. This is one of the more common fuel pump...
Other

How much is a brake caliper for a 2009 Dodge Journey?

How much is a brake caliper for a 2009 Dodge Journey? 2009 Dodge Journey Brake Caliper - Rear - from $79.99+ | AutoZone.com. How much are brake pads for 2014 Dodge Journey? 2014 Dodge Journey Brake Pads - from $32.99+ | AutoZone.com. How much are brakes for a 2013 Dodge Journey? 2013 Dodge Journey brake pads replacement, which includes parts and labor, can cost anywhere between $150 and $300 per axle depending on the type of brake pads desired and the extent of the damage your previously worn down pads have caused to the other components of your vehicle such...
Easy lifehacks

How can I Fix my Dodge Dakota idling?

How can I Fix my Dodge Dakota idling? Use 2 torx bits to remove it. Once removed, you will see a round piece on the inside part of it. This is a little wheel under slight tension. Very carefully using a flathead screwdriver, turn the wheel and let it snap back a few times, then reinstall. This takes about 5 minutes to do, and it has worked for me. Please award points if this helps Why does my 94 Dodge Dakota keep dying? My 94 dodge Dakota does the same thing, it dies randomly when I am driving, completely shuts...
Easy lifehacks

When was the first Dodge Nitro made?

When was the first Dodge Nitro made? Dodge NitroProductionAugust 2006–December 16, 2011Model years2007–2012AssemblyToledo, Ohio, United StatesBody and chassis When did my 2007 Dodge Nitro start up? In April 2017, started hearing my alarm on my 2007 Dodge Nitro RT start honking on it's own. Deactivating and Activating my alarm. Why does my Dodge Nitro SLT not start? I have a 2007 Dodge nitro SLT. Guess what? It wont start. We have replaced the battery and the starter. We got it to start one time after the replacements. We did this by taking the negative of the battery then the positive...
Easy lifehacks

Why does my minivan make a clunking noise when going over bumps?

Why does my minivan make a clunking noise when going over bumps? Every Chrysler minivan owner eventually complains about front suspension noise. The suspension makes clunking sounds when going over bumps. The problem can be narrowed down to two components—the stabilizer bar end links, and the stabilizer bar bushings. The stabilizer bar connects to the strut with an end link that contains two ball joints. What to do about clunking noise in Dodge Caravan? To install, simple insert the new end link and tighten the nuts that come with it. Stabilizer bar bushings can also generate clunking noises. The rubber...