Other

What are the sensors on the Transmission Control Module?

What are the sensors on the Transmission Control Module? Some of the sensors that work closely with the transmission control module are the transmission fluid temperature sensor, the turbine speed sensor, and the throttle position sensor. These sensors collect information about your vehicle’s performance and this data is sent to the transmission control module. What is a Transmission Control Unit ( TCU )? A transmission control unit (TCU) is an electronic device used on automatic vehicle transmissions to control the manner in which they work. Do comment and share your views. Constructive comments would be appreciated. Are there control modules...
Easy tips

How to remove the air intake in a Mazda 3?

How to remove the air intake in a Mazda 3? 1. Set the air intake mode to FRESH. 2. Disconnect the negative battery cable.. 3. Remove the following parts: a. Front scuff plate (Passenger-side). b. Front side trim (Passenger-side). c. Resistance Inspection NOTE: Because the IAT sensor is integrated in the MAF sensor, replacing the IAT sensor includes replacement of the MAF/IAT sensor. 1. How do you replace the intake manifold on a Honda Accord? Remove the intake manifold. 1. Temporarily tighten the throttle body to the intake manifold. 2. Tighten the installation bolts in the order shown in the...
Easy lifehacks

When did Ford F150 wiring diagram come out?

When did Ford F150 wiring diagram come out? Ford f150 wiring diagram 2004 2008. It shows the elements of the circuit as simplified forms as well as the power and signal connections in between the tools. With that said failed blower resistor assemblies dont solve all of the possible failures. A wiring diagram is a streamlined traditional pictorial representation of an electric circuit. What does a wiring diagram on a car mean? It shows the components of the circuit as simplified shapes, and the power and signal connections amongst the devices. A wiring diagram usually gives suggestion approximately the relative...
Other

Where do I put the temperature gauge on my car?

Where do I put the temperature gauge on my car? Choose a location for the temperature gauge mounting hole on the vehicle dashboard. Ensure that the gauge will be visible and that no wires or hoses behind the dash will be damaged when drilling the mounting hole. Use a drill and hole saw to make a 2 1/16 or 2 5/8 inch hole (depending on the gauge model) in the dashboard at the chosen location. How do you install a water temp gauge? Install the grommet in the hole in the firewall. Slide the temperature gauge into the mounting hole....
Easy tips

What engine is in the Ford Territory?

What engine is in the Ford Territory? Ford Territory (Australia)Ford TerritoryPowertrainEnginepetrol: 4.0 L Barra I6 4.0 L Barra turbo I6 diesel: 2.7 L Duratorq turbo V6Transmission4-speed M93LE automatic (SX; SY RWD) 6-speed 6HP21 automatic (SZ II petrol) 6-speed 6HP26 automatic (SY AWD; SZ petrol) 6-speed 6R80 (diesel)Dimensions When did Ford start making the Ford Territory? When Ford embarked on the development of the Territory back in the late 1990s, it was with a great understanding of what this boom in "four-wheel drives" -- or SUVs as they are now known -- was all about. When to get a second opinion...
Easy lifehacks

How to enable or disable Ford autolocks step by step?

How to enable or disable Ford autolocks step by step? 1. Confirm that the perimeter alarm is disarmed. 2. Close all doors. 3. Confirm that the ignition switch is in the OFF position. Note: Steps 4 through 8 must be performed within 30 seconds. 4. Turn the ignition switch from OFF to RUN. How to reset the anti theft system in a Ford? 1 Insert the key into the ignition and turn it on to the position where the accessories are activated but not the engine. 2 Leave the key in this position for at least 10 minutes. 3 Check...
Easy lifehacks

What can I do about the noise coming from my Radio?

What can I do about the noise coming from my Radio? If the noise stays the same or gets louder, it's coming in along the 12-volt power cables. Try removing the antenna from the fender and cleaning the fender sheetmetal and the antenna mount. Clean down to the shiny metal, using sandpaper to remove any corrosion. Smear the area lightly with Vaseline or dielectric grease, and reattach. Where does the noise from the radio come from? In other words, even though the noise comes from a radio speaker, it may be caused by any manner of device anywhere on your...
Easy lifehacks

What does the p0299 DTC code stand for?

What does the p0299 DTC code stand for? The P0299 DTC code refers to a condition where the PCM/ECM (powertrain/engine control module) has detected that the bank "A" or single turbocharger or supercharger is not providing a normal amount of boost (pressure). That could be due to a variety of reasons, which we detail below. What causes underboost on a Ford p0299? Reduced power output from engine, possibly in a "limp" mode There would likely be no other symptoms. Potential causes of a P0299 turbo underboost code include: Failed or damaged turbocharger (sticking, binding, etc.) Faulty injector control pressure (ICP)...
Other

When was the Ford Crown Victoria transmission introduced?

When was the Ford Crown Victoria transmission introduced? First introduced in 1992 for modular 4.6 liter engines in the Crown Victoria, Grand Marquis, and Town Car models, these transmissions are excellent choices for street performance with small block engines. By 1994, these units had completely replaced the older AOD. When did Ford stop using the AOD transmission? By 1994, these units had completely replaced the older AOD. They're readily available on the used market and are great for retrofitting into earlier vehicles. First year of the wide ratio gear set, available only in the Lincoln MKVIII Do you need a...
Easy lifehacks

How much does a shift fork cost?

How much does a shift fork cost? These cost between $20 and $50 each. Labor adds significantly to the clutch replacement cost when you entrust it to professionals. What is the purpose of a shift fork? A shift fork is a forked end metal lever that straddles a manual transmission gear shaft. Its purpose is to slide gears into or out of engagement with other gears in order change from one gear ratio to another in a manual transmission. What is a synchronizer sleeve? The sliding sleeve (6), also called gearshift sleeve, synchronizer sleeve or coupling sleeve, has a radial...