Most popular

What is inside a flywheel?

What is inside a flywheel? It consists of a spinning carbon-fiber cylinder mounted inside a very sturdy container, which is designed to stop any high-speed fragments if the rotor should break. Flywheels like this have an electric motor and/or generator attached, which stores the energy in the wheel and gets it back again later when it's needed. What are the three basic elements of flywheel? ... consist of a spinning rotor, MG, bearings, a power electronics interface, and containment or housing, which are discussed in detail in the following subsections. A typical flywheel system suitable for ground-based power is schematically...
Common questions

Is the Ford FE 390 the same as the 428?

Is the Ford FE 390 the same as the 428? Well it actually is the same for all ford FE's, this included the 352, 360, 390, 406, 427 and 428 engines. When I think of the Ford 'FE' ironically I think of Iron (no pun intended... well a little). When did the Ford 352 V8 come out? The Ford 352 V8 was first introduced in 1958 and would stay in the Ford lineup up through 1966. The 352 also was part a long-running series (1958-1976) of Ford engines known as the “FE” which means Ford-Edsel. For 1958, the 352 would...
Other

Where can I get a Jaguar XK engine rebuilt?

Where can I get a Jaguar XK engine rebuilt? Your old friends at CMC build engines, but the last time I spoke to them they were also sup-contracting out some of their work to VSE, as I recall they offered a 4.2 engine complete on their website which was built for them by VSE to CMC's spec, they also offered the option of having them do the work at a somewhat higher price. Where can I rebuild a classic Jaguar engine? Nobody enjoys paying the high price of an engine rebuild. When the time comes for you to give your...
Easy tips

How much is a 71 Charger worth?

How much is a 71 Charger worth? Data based on 149 auction sales. note: The images shown are representations of the 1971 Dodge Charger and not necessarily vehicles that have been bought or sold at auction....Dodge Models.BodystylesMedian Sale500 Series SE Hardtop$11,500500 Series Super Bee Hardtop$34,000Coupe$14,125Hardtop$24,200 How much did a 1970 Dodge Charger cost? The Charger was indeed an expensive car with a price tag of $3,100. How much horsepower did a 1970 Charger have? A stock 1970 Dodge Charger with the famed 440 Six Pack powerplant (three, two-barrel carburetors) was good for 390-horsepower. Not too shabby for a big ole...
Easy tips

Why is my Mercury outboard not getting spark?

Why is my Mercury outboard not getting spark? If one cylinder is not sparking, swap the White/Green and Green/White stator wires and retest. If the problem moves to the other cylinder, the stator is likely bad. If no change, replace both CDMs. A continued no spark condition on the same cylinder indicates a bad trigger. Why would a boat motor have no spark? Engines with no spark or intermittent spark on one bank can be caused by a faulty stator. Nestled in with the stator under the flywheel is the trigger (or timer base). What to do if there is...
Easy lifehacks

Can a battery case melt at a lower temp?

Can a battery case melt at a lower temp? Many electrical grade solders melt at a lower temp than the nylon used in a Nyloc nut does. The point here is that the ABYC standards still allow soldered on battery lugs (with no mechanical connection eg: crimp) and the solders above are very typical of electrical work such as soldered on battery lugs .. Battery Case Melting Point? Where are jumper wires supposed to be placed? Jumper wires should be placed on the component side of the circuit board assembly when possible. Of course many circuit board designs have components...
Easy lifehacks

What is a FJ40 Land Cruiser worth?

What is a FJ40 Land Cruiser worth? The FJ40 is the model that made Toyota a household name....Model years for Toyota Land Cruiser FJ40 (1961 to 1985)For Sale6Dollar Volume$18.0mLowest Sale$4,500Top Sale$135,000Most Recent$44,000 Is the FJ40 reliable? It's tough, it's reliable, it is the most fun car I've ever driven. It's rough around the edges, but it's also elegant in it's own way. I always tell people an FJ40 is pretty much the absolute minimum required to be a car. No frills, no comforts. When did Toyota stop making the FJ40? 1983 Toyota ended FJ40 sales in the U.S. in 1983...
Most popular

What happens when float height is too high?

What happens when float height is too high? In an extreme case, if the floats are set too high, fuel will overflow via drillings inside the carb body. In addition, fuel may flow into the engine unrestricted, which, if the engine is not running, can cause hydraulic lock – that is, as the piston rises on the compression stroke it cannot compress the fuel. What is float drop? A float drop tang located at the rear of the float arm prevents the float from moving too far downward. The maximum float drop must be maintained so that the float assembly...
Common questions

Where can I buy 1964 Ford Econoline parts?

Where can I buy 1964 Ford Econoline parts? Classic Industries is America's first choice for 1964 Ford Econoline parts and accessories. Replacement bendix drive assembly for Ford 12V Inertia Starter Motors. Where is the steering column on a 1964 Ford Econoline? Reproduction steering column weather seal for 1961-65 Econoline pickup trucks and vans. This seal installs beneath the metal floor plate and seals the columnl to the floor of the truck. It is the exact shape and size of the... Keep your Mustang cool without spending a small fortune on a radiator! What should I replace the tie rod on...
Most popular

What kind of car was the Dodge Phoenix in 1965?

What kind of car was the Dodge Phoenix in 1965? As a result, Dodge’s full-size ’65 car became the 121-inch (3073mm) wheelbase Polara/Monaco, with the Fairlane-sized Coronet introduced to plug the gap left by the old ’64 Polara. It was an inspired move. US Dodge sales soared, and the Fury prompted a dramatic two-year Plymouth turnaround. When did Plymouth poly 318 engine come out? Also in 1957, the Poly 318 was born by changing the stroke of the 301 to 3.31, for a bore and stroke of 3.91 X 3.31, and a displacement of 317.6ci. 1957 Plymouth Fury models got...